Nevermind. When you wrote you can set it in the BIOS, that means that userspace should not have to set it as far as I can tell from the code. It will just get set like other net settings if not passed in from userspace during session login time..
On 09/17/2014 01:39 AM, Mike Christie wrote: > See the email subject. What about iscsistart? It only takes info found > in /sys/firmware. iscsiadm can set any info in /etc/iscsi or > /var/lib/iscsi, so yeah that should work. > > On 09/16/2014 11:25 PM, Jayamohan Kallickal wrote: >> >> We do have code to set vlan id, so, we can set vlanid using iscsiadm >> >> Also, the Emulex BIOS allows for setting of vlan id. >> >> Thanks >> Jay >> >> -----Original Message----- >> From: Mike Christie [mailto:[email protected]] >> Sent: Monday, September 15, 2014 10:42 AM >> To: [email protected] >> Cc: Jayamohan Kallickal >> Subject: Re: iscsistart VLAN ID ?? >> >> If you are using be2iscsi, then you would not use ibft. If you are using a >> custom boot script then you need be2iscsi and iscsi_boot_sysfs only. >> If you are using a distro boot script then it might be more general and >> loading ibft (loading ibft loads iscsi_boot_sysfs) because other drivers >> need it. >> >> I think for be2iscsi boot, there is no code to get the vlan id and then pass >> that down to the driver. However, I think be2iscsi might store the vlan info >> in firmware like it does with the other net info. So as long as the vlan id >> did not change then you are ok. Jay, is that correct? >> >> >> >> On 09/15/2014 12:34 PM, Rob Roschewsk wrote: >>> be2iscsi .... but I've made more progress since this post ... see: >>> https://groups.google.com/d/msg/open-iscsi/JZVK8BBImg0/QS08QsAwX_wJ >>> >>> The configuration of the VLAN still seems to be automagic .... but >>> it's working .... >>> >>> >>> On Monday, September 15, 2014 5:23:25 PM UTC, Mike Christie wrote: >>> >>> On 09/11/2014 10:43 AM, Rob Roschewsk wrote: >>> > Hi all ... I've searched but have found no answers .... maybe my >>> > google-juice is low ... >>> > >>> > I need to be able to pass a VLAN ID and enable VLAN TAGGING in >>> iscsistart >>> > >>> > I'm using an EMULEX 10G NETWORK / ISCSI HBA and our iscsi traffic >>> is on >>> > a specific vlan >>> > >>> > Emulex Corporation OneConnect 10Gb NIC (be3) (rev 01) >>> > >>> >>> Are you using the Emulex iscsi offload driver (be2iscsi) or using >>> software iscsi (iscsi_tcp) over the Emulex network driver (be2net)? >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "open-iscsi" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected] >>> <mailto:[email protected]>. >>> To post to this group, send email to [email protected] >>> <mailto:[email protected]>. >>> Visit this group at http://groups.google.com/group/open-iscsi. >>> For more options, visit https://groups.google.com/d/optout. >> > -- You received this message because you are subscribed to the Google Groups "open-iscsi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/open-iscsi. For more options, visit https://groups.google.com/d/optout.
