I have discovered how to name the dynamic inferfaces (select one, then click on the settings icon). Just need to work out why the main chart looks too high.
If I look at the main chart for an interface, the 1 hour chart shows a much higher maximum than the 3 hour chart, although both are too high. What's going on there? > -----Original Message----- > From: [email protected] [mailto:ntop- > [email protected]] On Behalf Of Peter Shute > Sent: Tuesday, 13 February 2018 8:07 AM > To: [email protected] > Subject: Re: [Ntop] Combining subnet statistics > > Thanks for that. I've also discovered I can separate out the netflow data > coming from each office's router using dynamic network interfaces. I > followed the instructions provided at > https://github.com/ntop/ntopng/issues/1444 to enable Probe IP > disaggregation criterion, and to add %EXPORTER_IPV4_ADDRESS to the > template. I assume this does the same thing as host pooling, assuming one > wants to pool every subnet on each router? I have this running now, so I > can't try creating host pools unless I undo those changes. > > One thing I've noticed with dynamic interfaces is that if I select one, then > click > on the chart icon, the traffic peaks seem way too high. Eg 85Mbps when we > only have a 14Mbps link. If I click on Hosts/Networks, and select one of the > local subnets, it seems ok. Is there something wrong with that combined > chart? > > Is it possible to name the dynamic network interfaces so I don't have to keep > a list of all the routers' ip addresses? > > > -----Original Message----- > > From: [email protected] [mailto:ntop- > > [email protected]] On Behalf Of Simone Mainardi > > Sent: Tuesday, 13 February 2018 1:29 AM > > To: [email protected] > > Subject: Re: [Ntop] Combining subnet statistics > > > > Yes, you can do that. > > > > You should create an host pool for any branch you are interested > monitoring. > > An host pool can be defined as a set of subnets so this will do the trick. > Once > > you've created the pools, visit the ntopng preferences and enable the > > timeseries creation for them. > > > > Simone > > > > > On 12 Feb 2018, at 00:08, Peter Shute <[email protected]> wrote: > > > > > > We have several subnets in each of our branch offices that can use our > > WAN. I have listed each of these in ntopng.conf: > > > --local-networks= > > > "192.168.0.0/23,192.168.2.0/24,192.168.3.0/24,192.168.6.0/24,192.168.7.0/24, > > > 192.168.30.0/24,192.168.60.0/24,192.168.32.0/24,192.168.62.0/24,192.168.33. > > 0/24,192.168.3.0/24,192.168.37.0/24,192.168.67.0/24" > > > > > > I can view charts for each subnet individually, but I would like to see > > > the > > total for each branch office. E.g 192.168.2.0/24 + 192.168.32.0/24 + > > 192.168.62.0/24. > > > > > > Is there a way to do this? Because of the subnet ranges they've used (last > > digit of second last number indicates branch office), I can't just define a > > subnet range to cover them. > > > > > > Peter Shute > > > _______________________________________________ > > > Ntop mailing list > > > [email protected] > > > http://listgateway.unipi.it/mailman/listinfo/ntop > > > > _______________________________________________ > > Ntop mailing list > > [email protected] > > http://listgateway.unipi.it/mailman/listinfo/ntop > _______________________________________________ > Ntop mailing list > [email protected] > http://listgateway.unipi.it/mailman/listinfo/ntop _______________________________________________ Ntop mailing list [email protected] http://listgateway.unipi.it/mailman/listinfo/ntop
