Hi Jesse, > On 22 Nov 2016, at 20:24, Jesse Alexander <[email protected]> wrote: > > Thank you Luca. I ran the update and it seems to run without the error now. > > It is odd though, since the upgrade the front end GUI now only shows traffic > on the dashboard for half of the interfaces. However, when I look at our > graphs for the nbox host, I see normal traffic on all of the interfaces. It > appears to be cosmetic, but just an observation I wish to share. No it was not cosmetic, it was an error. Thanks for reporting it
> > Also, one quick question. When we are exporting using Netflow v9, are we > also exporting IPv6 traffic? Yes I do > > Kind regards, > Regards Luca > Jesse > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Luca Deri > Sent: Tuesday, November 22, 2016 4:22 AM > To: [email protected] > Subject: Re: [Ntop-misc] NPROBE CENTO Out of bounday error > > Hi Jesse, > I have inspected the code, and I believe I have found a case where the > bug you reported can be reproduced. I have fixed it and packages are > being rebuilt. Please try again later today and let me know if the issue > is gone. > > Thanks Luca > > On 11/21/2016 09:27 PM, Jesse Alexander wrote: >> Hello, >> >> Beginning today, we are receiving an error when running Cento that I haven't >> seen before. I am very new to running Cento, so I suspect I am doing >> something wrong and hoping for some assistance. >> >> I am running Cento ZC on eight 10G Myricom ports to export netflow v9. Not >> long after I start running it, I see errors like the following, then it >> stops running: >> >> 21/Nov/2016 02:26:30 [NetflowExporterV9.cpp:172] ERROR: *** Out of bounday >> [3493/1470][18952/22 flows] >> 21/Nov/2016 02:26:30 [NetflowExporterV9.cpp:172] ERROR: *** Out of bounday >> [3557/1470][18953/22 flows] >> 21/Nov/2016 02:26:30 [NetflowExporterV9.cpp:172] ERROR: *** Out of bounday >> [3621/1470][18954/22 flows] >> 21/Nov/2016 02:26:30 [NetflowExporterV9.cpp:172] ERROR: *** Out of bounday >> [3685/1470][18955/22 flows] >> 21/Nov/2016 02:26:30 [NetflowExporterV9.cpp:172] ERROR: *** Out of bounday >> [3749/1470][18956/22 flows] >> >> I am running the following: >> sudo cento -i myri1-1,myri1-2 -i myri2-1,myri2-2 -i myri3-1,myri3-2 -i >> myri4-1,myri4-2 -g 4,6,8,9,10,11,12,13,14,15,16,18 -G 2,3,7,17,19,20 --v9 >> 10.10.10.2:2055 >> >> I know the Myricom naming convention is a bit different than default, which >> was intentional, but until today it has run great. Only change today is I >> added two additional interfaces to export. I am unable to find any online >> reference to CPP errors for Netflow v9 to point me in the right direction. >> >> Thank you in advance, >> >> Jesse >> _______________________________________________ >> Ntop-misc mailing list >> [email protected] >> http://listgateway.unipi.it/mailman/listinfo/ntop-misc > > > _______________________________________________ > Ntop-misc mailing list > [email protected] > http://listgateway.unipi.it/mailman/listinfo/ntop-misc > _______________________________________________ > Ntop-misc mailing list > [email protected] > http://listgateway.unipi.it/mailman/listinfo/ntop-misc _______________________________________________ Ntop-misc mailing list [email protected] http://listgateway.unipi.it/mailman/listinfo/ntop-misc
