On Mon, 2007-07-09 at 15:14 -0400, Sinan Akman wrote:
> [EMAIL PROTECTED] wrote:
>
> >From: "Wu, Bryan" <[EMAIL PROTECTED]>
> >
> >This patch implements the driver necessary use the Analog Devices
> >Blackfin processor's on-chip ethernet MAC controller.
> >
> >Signed-off-by: Bryan Wu <[EMAIL PROTECTED]>
> >Cc: Jeff Garzik <[EMAIL PROTECTED]>
> >Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
> >---
> >
> > drivers/net/Kconfig | 44 +
> > drivers/net/Makefile | 1
> > drivers/net/bfin_mac.c | 981 +++++++++++++++++++++++++++++++++++++++
> > drivers/net/bfin_mac.h | 147 +++++
> > 4 files changed, 1173 insertions(+)
> >
> >diff -puN
> >drivers/net/Kconfig~blackfin-on-chip-ethernet-mac-controller-driver
> >drivers/net/Kconfig
> >--- a/drivers/net/Kconfig~blackfin-on-chip-ethernet-mac-controller-driver
> >+++ a/drivers/net/Kconfig
> >@@ -821,6 +821,50 @@ config ULTRA32
> > <file:Documentation/networking/net-modules.txt>. The module
> > will be called smc-ultra32.
> >
> >+config BFIN_MAC
> >+ tristate "Blackfin 536/537 on-chip mac support"
> >+ depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
> >+ select CRC32
> >+ select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
> >+ help
> >+ This is the driver for blackfin on-chip mac device. Say Y if you want
> >it
> >+ compiled into the kernel. This driver is also available as a module
> >+ ( = code which can be inserted in and removed from the running kernel
> >+ whenever you want). The module will be called bfin_mac.
> >+
> >+config BFIN_MAC_USE_L1
> >+ bool "Use L1 memory for rx/tx packets"
> >+ depends on BFIN_MAC && BF537
> >+ default y
> >+ help
> >+ To get maximum network performace, you should use L1 memory as rx/tx
> >buffers.
> >+ Say N here if you want to reserve L1 memory for other uses.
> >+
> >+config BFIN_TX_DESC_NUM
> >+ int "Number of transmit buffer packets"
> >+ depends on BFIN_MAC
> >+ range 6 10 if BFIN_MAC_USE_L1
> >+ range 10 100
> >+ default "10"
> >+ help
> >+ Set the number of buffer packets used in driver.
> >+
> >+config BFIN_RX_DESC_NUM
> >+ int "Number of receive buffer packets"
> >+ depends on BFIN_MAC
> >+ range 20 100 if BFIN_MAC_USE_L1
> >+ range 20 800
> >+ default "20"
> >+ help
> >+ Set the number of buffer packets used in driver.
> >+
> >+config BFIN_MAC_RMII
> >+ bool "RMII PHY Interface (EXPERIMENTAL)"
> >+ depends on BFIN_MAC && EXPERIMENTAL
> >+ default n
> >+ help
> >+ Use Reduced PHY MII Interface
> >+
> > config SMC9194
> > tristate "SMC 9194 support"
> > depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
> >diff -puN
> >drivers/net/Makefile~blackfin-on-chip-ethernet-mac-controller-driver
> >drivers/net/Makefile
> >--- a/drivers/net/Makefile~blackfin-on-chip-ethernet-mac-controller-driver
> >+++ a/drivers/net/Makefile
> >@@ -195,6 +195,7 @@ obj-$(CONFIG_S2IO) += s2io.o
> > obj-$(CONFIG_MYRI10GE) += myri10ge/
> > obj-$(CONFIG_SMC91X) += smc91x.o
> > obj-$(CONFIG_SMC911X) += smc911x.o
> >+obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
> > obj-$(CONFIG_DM9000) += dm9000.o
> > obj-$(CONFIG_FEC_8XX) += fec_8xx/
> > obj-$(CONFIG_PASEMI_MAC) += pasemi_mac.o
> >diff -puN /dev/null drivers/net/bfin_mac.c
> >--- /dev/null
> >+++ a/drivers/net/bfin_mac.c
> >@@ -0,0 +1,981 @@
> >+/*
> >+ * File: drivers/net/bfin_mac.c
> >+ * Based on:
> >+ * Author: Luke Yang <[EMAIL PROTECTED]>
> >+ *
> >+ * Created:
> >+ * Description:
> >+ *
> >+ * Modified:
> >+ * Copyright 2004-2006 Analog Devices Inc.
> >+ *
> >+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
> >+ *
> >+ * This program is free software ; you can redistribute it and/or modify
> >+ * it under the terms of the GNU General Public License as published by
> >+ * the Free Software Foundation ; either version 2, or (at your option)
> >+ * any later version.
> >+ *
> >+ * This program is distributed in the hope that it will be useful,
> >+ * but WITHOUT ANY WARRANTY ; without even the implied warranty of
> >+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >+ * GNU General Public License for more details.
> >+ *
> >+ * You should have received a copy of the GNU General Public License
> >+ * along with this program ; see the file COPYING.
> >+ * If not, write to the Free Software Foundation,
> >+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
> >+ */
> >+
> >+#include <linux/init.h>
> >+#include <linux/module.h>
> >+#include <linux/kernel.h>
> >+#include <linux/sched.h>
> >+#include <linux/slab.h>
> >+#include <linux/delay.h>
> >+#include <linux/timer.h>
> >+#include <linux/errno.h>
> >+#include <linux/ioport.h>
> >+#include <linux/crc32.h>
> >+#include <linux/device.h>
> >+#include <linux/spinlock.h>
> >+#include <linux/ethtool.h>
> >+#include <linux/mii.h>
> >+
> >+#include <linux/netdevice.h>
> >+#include <linux/etherdevice.h>
> >+#include <linux/skbuff.h>
> >+
> >+#include <linux/platform_device.h>
> >+#include <linux/netdevice.h>
> >+#include <linux/etherdevice.h>
> >+#include <linux/skbuff.h>
> >+
> >+#include <asm/io.h>
> >+#include <asm/irq.h>
> >+#include <asm/dma.h>
> >+#include <linux/dma-mapping.h>
> >+
> >+#include <asm/irq.h>
> >+#include <asm/blackfin.h>
> >+#include <asm/delay.h>
> >
> >
> Something very minor, but are
> netdevice.h, etherdevice.h etc
> being included here twice ?
>
Thanks, Sinan.
I am packing up all patches for current merge window.
This driver will be resent with you guys' review.
-Bryan Wu
> >+
> >+#include "bfin_mac.h"
> >+
> >+#define CARDNAME "bfin_mac"
> >+
> >+MODULE_LICENSE("GPL");
> >+MODULE_AUTHOR("Luke Yang");
> >+MODULE_DESCRIPTION("Blackfin MAC Driver");
> >+
> >+#if defined(CONFIG_BFIN_MAC_USE_L1)
> >+# define bfin_mac_alloc(dma_handle, size) l1_data_sram_zalloc(size)
> >+# define bfin_mac_free(dma_handle, ptr) l1_data_sram_free(ptr)
> >+#else
> >+# define bfin_mac_alloc(dma_handle, size) dma_alloc_coherent(NULL, size,
> >dma_handle, GFP_DMA)
> >+# define bfin_mac_free(dma_handle, ptr) dma_free_coherent(NULL,
> >sizeof(*ptr), ptr, dma_handle)
> >+#endif
> >+
> >+#define PKT_BUF_SZ 1580
> >+
> >+static void desc_list_free(void);
> >+
> >+/* pointers to maintain transmit list */
> >+static struct net_dma_desc_tx *tx_list_head;
> >+static struct net_dma_desc_tx *tx_list_tail;
> >+static struct net_dma_desc_rx *rx_list_head;
> >+static struct net_dma_desc_rx *rx_list_tail;
> >+static struct net_dma_desc_rx *current_rx_ptr;
> >+static struct net_dma_desc_tx *current_tx_ptr;
> >+static struct net_dma_desc_tx *tx_desc;
> >+static struct net_dma_desc_rx *rx_desc;
> >+
> >+static int desc_list_init(void)
> >+{
> >+ struct net_dma_desc_tx *tmp_desc_tx;
> >+ struct net_dma_desc_rx *tmp_desc_rx;
> >+ int i;
> >+ struct sk_buff *new_skb;
> >+#if !defined(CONFIG_BFIN_MAC_USE_L1)
> >+ dma_addr_t dma_handle;
> >+#endif
> >+
> >+ tx_desc =
> >+ bfin_mac_alloc(&dma_handle,
> >+ sizeof(struct net_dma_desc_tx) *
> >+ CONFIG_BFIN_TX_DESC_NUM);
> >+ if (tx_desc == NULL)
> >+ goto init_error;
> >+
> >+ rx_desc =
> >+ bfin_mac_alloc(&dma_handle,
> >+ sizeof(struct net_dma_desc_rx) *
> >+ CONFIG_BFIN_RX_DESC_NUM);
> >+ if (rx_desc == NULL)
> >+ goto init_error;
> >+
> >+ /* init tx_list */
> >+ for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
> >+
> >+ tmp_desc_tx = tx_desc + i;
> >+
> >+ if (i == 0) {
> >+ tx_list_head = tmp_desc_tx;
> >+ tx_list_tail = tmp_desc_tx;
> >+ }
> >+
> >+ tmp_desc_tx->desc_a.start_addr =
> >+ (unsigned long)tmp_desc_tx->packet;
> >+ tmp_desc_tx->desc_a.x_count = 0;
> >+ tmp_desc_tx->desc_a.config.b_DMA_EN = 0; /* disabled */
> >+ tmp_desc_tx->desc_a.config.b_WNR = 0; /* read from
> >memory */
> >+ tmp_desc_tx->desc_a.config.b_WDSIZE = 2; /* wordsize is
> >32 bits */
> >+ tmp_desc_tx->desc_a.config.b_NDSIZE = 6; /* 6 half words
> >is desc size. */
> >+ tmp_desc_tx->desc_a.config.b_FLOW = 7; /* large desc
> >flow */
> >+ tmp_desc_tx->desc_a.next_dma_desc = &(tmp_desc_tx->desc_b);
> >+
> >+ tmp_desc_tx->desc_b.start_addr =
> >+ (unsigned long)(&(tmp_desc_tx->status));
> >+ tmp_desc_tx->desc_b.x_count = 0;
> >+ tmp_desc_tx->desc_b.config.b_DMA_EN = 1; /* enabled */
> >+ tmp_desc_tx->desc_b.config.b_WNR = 1; /* write to
> >memory */
> >+ tmp_desc_tx->desc_b.config.b_WDSIZE = 2; /* wordsize is
> >32 bits */
> >+ tmp_desc_tx->desc_b.config.b_DI_EN = 0; /* disable
> >interrupt */
> >+ tmp_desc_tx->desc_b.config.b_NDSIZE = 6;
> >+ tmp_desc_tx->desc_b.config.b_FLOW = 7; /* stop mode */
> >+ tmp_desc_tx->skb = NULL;
> >+ tx_list_tail->desc_b.next_dma_desc = &(tmp_desc_tx->desc_a);
> >+ tx_list_tail->next = tmp_desc_tx;
> >+
> >+ tx_list_tail = tmp_desc_tx;
> >+ }
> >+ tx_list_tail->next = tx_list_head; /* tx_list is a circle */
> >+ tx_list_tail->desc_b.next_dma_desc = &(tx_list_head->desc_a);
> >+ current_tx_ptr = tx_list_head;
> >+
> >+ /* init rx_list */
> >+ for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
> >+
> >+ tmp_desc_rx = rx_desc + i;
> >+
> >+ if (i == 0) {
> >+ rx_list_head = tmp_desc_rx;
> >+ rx_list_tail = tmp_desc_rx;
> >+ }
> >+
> >+ /* allocat a new skb for next time receive */
> >+ new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
> >+ if (!new_skb) {
> >+ printk(KERN_NOTICE CARDNAME
> >+ ": init: low on mem - packet dropped\n");
> >+ goto init_error;
> >+ }
> >+ skb_reserve(new_skb, 2);
> >+ tmp_desc_rx->skb = new_skb;
> >+ /* since RXDWA is enabled */
> >+ tmp_desc_rx->desc_a.start_addr =
> >+ (unsigned long)new_skb->data - 2;
> >+ tmp_desc_rx->desc_a.x_count = 0;
> >+ tmp_desc_rx->desc_a.config.b_DMA_EN = 1; /* enabled */
> >+ tmp_desc_rx->desc_a.config.b_WNR = 1; /* Write to
> >memory */
> >+ tmp_desc_rx->desc_a.config.b_WDSIZE = 2; /* wordsize is
> >32 bits */
> >+ tmp_desc_rx->desc_a.config.b_NDSIZE = 6; /* 6 half words
> >is desc size. */
> >+ tmp_desc_rx->desc_a.config.b_FLOW = 7; /* large desc
> >flow */
> >+ tmp_desc_rx->desc_a.next_dma_desc = &(tmp_desc_rx->desc_b);
> >+
> >+ tmp_desc_rx->desc_b.start_addr =
> >+ (unsigned long)(&(tmp_desc_rx->status));
> >+ tmp_desc_rx->desc_b.x_count = 0;
> >+ tmp_desc_rx->desc_b.config.b_DMA_EN = 1; /* enabled */
> >+ tmp_desc_rx->desc_b.config.b_WNR = 1; /* Write to
> >memory */
> >+ tmp_desc_rx->desc_b.config.b_WDSIZE = 2; /* wordsize is
> >32 bits */
> >+ tmp_desc_rx->desc_b.config.b_NDSIZE = 6;
> >+ tmp_desc_rx->desc_b.config.b_DI_EN = 1; /* enable
> >interrupt */
> >+ tmp_desc_rx->desc_b.config.b_FLOW = 7; /* large mode */
> >+ rx_list_tail->desc_b.next_dma_desc = &(tmp_desc_rx->desc_a);
> >+
> >+ rx_list_tail->next = tmp_desc_rx;
> >+ rx_list_tail = tmp_desc_rx;
> >+ }
> >+ rx_list_tail->next = rx_list_head; /* rx_list is a circle */
> >+ rx_list_tail->desc_b.next_dma_desc = &(rx_list_head->desc_a);
> >+ current_rx_ptr = rx_list_head;
> >+
> >+ return 0;
> >+
> >+ init_error:
> >+ desc_list_free();
> >+ printk(KERN_ERR CARDNAME ": kmalloc failed\n");
> >+ return -ENOMEM;
> >+}
> >+
> >+static void desc_list_free(void)
> >+{
> >+ struct net_dma_desc_rx *tmp_desc_rx;
> >+ struct net_dma_desc_tx *tmp_desc_tx;
> >+ int i;
> >+#if !defined(CONFIG_BFIN_MAC_USE_L1)
> >+ dma_addr_t dma_handle = 0;
> >+#endif
> >+
> >+ if (tx_desc != NULL) {
> >+ tmp_desc_tx = tx_list_head;
> >+ for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
> >+ if (tmp_desc_tx != NULL) {
> >+ if (tmp_desc_tx->skb) {
> >+ dev_kfree_skb(tmp_desc_tx->skb);
> >+ tmp_desc_tx->skb = NULL;
> >+ }
> >+
> >+ }
> >+ tmp_desc_tx = tmp_desc_tx->next;
> >+ }
> >+ bfin_mac_free(dma_handle, tx_desc);
> >+ }
> >+
> >+ if (rx_desc != NULL) {
> >+ tmp_desc_rx = rx_list_head;
> >+ for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
> >+ if (tmp_desc_rx != NULL) {
> >+ if (tmp_desc_rx->skb) {
> >+ dev_kfree_skb(tmp_desc_rx->skb);
> >+ tmp_desc_rx->skb = NULL;
> >+ }
> >+ }
> >+ tmp_desc_rx = tmp_desc_rx->next;
> >+ }
> >+ bfin_mac_free(dma_handle, rx_desc);
> >+ }
> >+}
> >+
> >+/*---PHY CONTROL AND
> >CONFIGURATION-----------------------------------------*/
> >+
> >+/* Set FER regs to MUX in Ethernet pins */
> >+static void setup_pin_mux(void)
> >+{
> >+ unsigned int fer_val;
> >+
> >+ /*
> >+ * FER reg bug work-around
> >+ * read it once
> >+ */
> >+ fer_val = bfin_read_PORTH_FER();
> >+
> >+#if defined(CONFIG_BFIN_MAC_RMII)
> >+ fer_val = 0xC373;
> >+#else
> >+ fer_val = 0xffff;
> >+#endif
> >+ /* write it twice to the same value */
> >+
> >+ bfin_write_PORTH_FER(fer_val);
> >+ bfin_write_PORTH_FER(fer_val);
> >+}
> >+
> >+/* Wait until the previous MDC/MDIO transaction has completed */
> >+static void poll_mdc_done(void)
> >+{
> >+ /* poll the STABUSY bit */
> >+ while ((bfin_read_EMAC_STAADD()) & STABUSY) {
> >+ };
> >+}
> >+
> >+/* Read an off-chip register in a PHY through the MDC/MDIO port */
> >+static u16 read_phy_reg(u16 PHYAddr, u16 RegAddr)
> >+{
> >+ poll_mdc_done();
> >+ bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) |
> >STABUSY); /* read mode */
> >+ poll_mdc_done();
> >+
> >+ return (u16) bfin_read_EMAC_STADAT();
> >+}
> >+
> >+/* Write an off-chip register in a PHY through the MDC/MDIO port */
> >+static void raw_write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
> >+{
> >+ bfin_write_EMAC_STADAT(Data);
> >+
> >+ bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) | STAOP
> >| STABUSY); /* write mode */
> >+
> >+ poll_mdc_done();
> >+}
> >+
> >+static void write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
> >+{
> >+ poll_mdc_done();
> >+ raw_write_phy_reg(PHYAddr, RegAddr, Data);
> >+}
> >+
> >+/* set up the phy */
> >+static void bf537mac_setphy(struct net_device *dev)
> >+{
> >+ u16 phydat;
> >+ u32 sysctl;
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+
> >+ pr_debug("start settting up phy\n");
> >+
> >+ /* Program PHY registers */
> >+ phydat = 0;
> >+
> >+ /* issue a reset */
> >+ raw_write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, 0x8000);
> >+
> >+ /* wait half a second */
> >+ udelay(500);
> >+
> >+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
> >+
> >+ /* advertise flow control supported */
> >+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_ANAR);
> >+ phydat |= (1 << 10);
> >+ write_phy_reg(lp->PhyAddr, PHYREG_ANAR, phydat);
> >+
> >+ phydat = 0;
> >+ if (lp->Negotiate) {
> >+ phydat |= 0x1000; /* enable auto negotiation */
> >+ } else {
> >+ if (lp->FullDuplex) {
> >+ phydat |= (1 << 8); /* full duplex */
> >+ } else {
> >+ phydat &= (~(1 << 8)); /* half duplex */
> >+ }
> >+ if (!lp->Port10) {
> >+ phydat |= (1 << 13); /* 100 Mbps */
> >+ } else {
> >+ phydat &= (~(1 << 13)); /* 10 Mbps */
> >+ }
> >+ }
> >+
> >+ if (lp->Loopback) {
> >+ phydat |= (1 << 14); /* enable TX->RX loopback */
> >+#if 0
> >+ write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
> >+#endif
> >+ }
> >+
> >+ write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
> >+ udelay(500);
> >+
> >+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
> >+ /* check for SMSC PHY */
> >+ if ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID1) == 0x7)
> >+ && ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID2) & 0xfff0) == 0xC0A0))
> >{
> >+ /* we have SMSC PHY so reqest interrupt on link down condition
> >*/
> >+ write_phy_reg(lp->PhyAddr, 30, 0x0ff); /* enable interrupts */
> >+ /* enable PHY_INT */
> >+ sysctl = bfin_read_EMAC_SYSCTL();
> >+ sysctl |= 0x1;
> >+#if 0
> >+ bfin_write_EMAC_SYSCTL(sysctl);
> >+#endif
> >+ }
> >+}
> >+
> >+/**************************************************************************/
> >+void setup_system_regs(struct net_device *dev)
> >+{
> >+ int PHYADDR;
> >+ unsigned short sysctl, phydat;
> >+ u32 opmode;
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+ int count = 0;
> >+
> >+ PHYADDR = lp->PhyAddr;
> >+
> >+ /* Enable PHY output */
> >+ if (!(bfin_read_VR_CTL() & PHYCLKOE))
> >+ bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
> >+
> >+ /* MDC = 2.5 MHz */
> >+ sysctl = SET_MDCDIV(24);
> >+ /* Odd word alignment for Receive Frame DMA word */
> >+ /* Configure checksum support and rcve frame word alignment */
> >+#if defined(BFIN_MAC_CSUM_OFFLOAD)
> >+ sysctl |= RXDWA | RXCKS;
> >+#else
> >+ sysctl |= RXDWA;
> >+#endif
> >+ bfin_write_EMAC_SYSCTL(sysctl);
> >+ /* auto negotiation on */
> >+ /* full duplex */
> >+ /* 100 Mbps */
> >+ phydat = PHY_ANEG_EN | PHY_DUPLEX | PHY_SPD_SET;
> >+ write_phy_reg(PHYADDR, PHYREG_MODECTL, phydat);
> >+
> >+ /* test if full duplex supported */
> >+ do {
> >+ msleep(100);
> >+ phydat = read_phy_reg(PHYADDR, PHYREG_MODESTAT);
> >+ if (count > 30) {
> >+ printk(KERN_NOTICE CARDNAME
> >+ ": Link is down, please check your network
> >connection\n");
> >+ break;
> >+ }
> >+ count++;
> >+ } while (!(phydat & 0x0004));
> >+
> >+ phydat = read_phy_reg(PHYADDR, PHYREG_ANLPAR);
> >+
> >+ if ((phydat & 0x0100) || (phydat & 0x0040)) {
> >+ opmode = FDMODE;
> >+ } else {
> >+ opmode = 0;
> >+ printk(KERN_INFO CARDNAME ": Network is set to half duplex\n");
> >+ }
> >+
> >+#if defined(CONFIG_BFIN_MAC_RMII)
> >+ opmode |= RMII; /* For Now only 100MBit are supported */
> >+#endif
> >+
> >+ bfin_write_EMAC_OPMODE(opmode);
> >+
> >+#if 0
> >+ bfin_write_EMAC_MMC_CTL(RSTC | CROLL | MMCE);
> >+#endif
> >+ bfin_write_EMAC_MMC_CTL(RSTC | CROLL);
> >+
> >+ /* Initialize the TX DMA channel registers */
> >+ bfin_write_DMA2_X_COUNT(0);
> >+ bfin_write_DMA2_X_MODIFY(4);
> >+ bfin_write_DMA2_Y_COUNT(0);
> >+ bfin_write_DMA2_Y_MODIFY(0);
> >+
> >+ /* Initialize the RX DMA channel registers */
> >+ bfin_write_DMA1_X_COUNT(0);
> >+ bfin_write_DMA1_X_MODIFY(4);
> >+ bfin_write_DMA1_Y_COUNT(0);
> >+ bfin_write_DMA1_Y_MODIFY(0);
> >+}
> >+
> >+void setup_mac_addr(u8 * mac_addr)
> >+{
> >+ /* this depends on a little-endian machine */
> >+ bfin_write_EMAC_ADDRLO(*(u32 *) & mac_addr[0]);
> >+ bfin_write_EMAC_ADDRHI(*(u16 *) & mac_addr[4]);
> >+}
> >+
> >+static void adjust_tx_list(void)
> >+{
> >+ if (tx_list_head->status.status_word != 0
> >+ && current_tx_ptr != tx_list_head) {
> >+ goto adjust_head; /* released something, just return; */
> >+ }
> >+
> >+ /* if nothing released, check wait condition */
> >+ /* current's next can not be the head, otherwise the dma will not stop
> >as we want */
> >+ if (current_tx_ptr->next->next == tx_list_head) {
> >+ while (tx_list_head->status.status_word == 0) {
> >+ udelay(10);
> >+ if (tx_list_head->status.status_word != 0
> >+ || !(bfin_read_DMA2_IRQ_STATUS() & 0x08)) {
> >+ goto adjust_head;
> >+ }
> >+ }
> >+ if (tx_list_head->status.status_word != 0) {
> >+ goto adjust_head;
> >+ }
> >+ }
> >+
> >+ return;
> >+
> >+ adjust_head:
> >+ do {
> >+ tx_list_head->desc_a.config.b_DMA_EN = 0;
> >+ tx_list_head->status.status_word = 0;
> >+ if (tx_list_head->skb) {
> >+ dev_kfree_skb(tx_list_head->skb);
> >+ tx_list_head->skb = NULL;
> >+ } else {
> >+ printk(KERN_ERR CARDNAME
> >+ ": no sk_buff in a transmitted frame!\n");
> >+ }
> >+ tx_list_head = tx_list_head->next;
> >+ } while (tx_list_head->status.status_word != 0
> >+ && current_tx_ptr != tx_list_head);
> >+ return;
> >+
> >+}
> >+
> >+static int bf537mac_hard_start_xmit(struct sk_buff *skb, struct net_device
> >*dev)
> >+{
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+ unsigned int data;
> >+
> >+ current_tx_ptr->skb = skb;
> >+ /* Is skb->data always 16-bit aligned? Do we need to memcpy((char
> >*)(tail->packet + 2),skb->data,len)? */
> >+ if ((((unsigned int)(skb->data)) & 0x02) == 2) {
> >+ /* move skb->data to current_tx_ptr payload */
> >+ data = (unsigned int)(skb->data) - 2;
> >+ *((unsigned short *)data) = (unsigned short)(skb->len);
> >+ current_tx_ptr->desc_a.start_addr = (unsigned long)data;
> >+ blackfin_dcache_flush_range(data, (data + (skb->len)) + 2);
> >/* this is important! */
> >+
> >+ } else {
> >+ *((unsigned short *)(current_tx_ptr->packet)) =
> >+ (unsigned short)(skb->len);
> >+ memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
> >+ (skb->len));
> >+ current_tx_ptr->desc_a.start_addr =
> >+ (unsigned long)current_tx_ptr->packet;
> >+ if (current_tx_ptr->status.status_word != 0)
> >+ current_tx_ptr->status.status_word = 0;
> >+ blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
> >+ packet,
> >+ (unsigned int)(current_tx_ptr->
> >+ packet + skb->len) +
> >+ 2);
> >+ }
> >+
> >+ current_tx_ptr->desc_a.config.b_DMA_EN = 1; /* enable this packet's
> >dma */
> >+
> >+ if (bfin_read_DMA2_IRQ_STATUS() & 0x08) { /* tx dma is running,
> >just return */
> >+ goto out;
> >+ } else {
> >+ /* tx dma is not running */
> >+ bfin_write_DMA2_NEXT_DESC_PTR(&(current_tx_ptr->desc_a));
> >+ /* dma enabled, read from memory, size is 6 */
> >+ bfin_write_DMA2_CONFIG(*((unsigned short
> >*)(&(current_tx_ptr->desc_a.config))));
> >+ /* Turn on the EMAC tx */
> >+ bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() | TE);
> >+ }
> >+
> >+ out:
> >+ adjust_tx_list();
> >+ current_tx_ptr = current_tx_ptr->next;
> >+ dev->trans_start = jiffies;
> >+ lp->stats.tx_packets++;
> >+ lp->stats.tx_bytes += (skb->len);
> >+ return 0;
> >+}
> >+
> >+static void bf537mac_rx(struct net_device *dev)
> >+{
> >+ struct sk_buff *skb, *new_skb;
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+ unsigned short len;
> >+
> >+ /* allocat a new skb for next time receive */
> >+ skb = current_rx_ptr->skb;
> >+ new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
> >+ if (!new_skb) {
> >+ printk(KERN_NOTICE CARDNAME
> >+ ": rx: low on mem - packet dropped\n");
> >+ lp->stats.rx_dropped++;
> >+ goto out;
> >+ }
> >+ /* reserve 2 bytes for RXDWA padding */
> >+ skb_reserve(new_skb, 2);
> >+ current_rx_ptr->skb = new_skb;
> >+ current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2;
> >+
> >+#if 0
> >+ int i;
> >+ if (len >= 64) {
> >+ for (i=0;i<len;i++) {
> >+ printk("%.2x-",((unsigned char *)pkt)[i]);
> >+ if (((i%8)==0) && (i!=0)) printk("\n");
> >+ }
> >+ printk("\n");
> >+ }
> >+#endif
> >+
> >+ len = (unsigned short)((current_rx_ptr->status.status_word) & RX_FRLEN);
> >+ skb_put(skb, len);
> >+ blackfin_dcache_invalidate_range((unsigned long)skb->head,
> >+ (unsigned long)skb->tail);
> >+
> >+ dev->last_rx = jiffies;
> >+ skb->dev = dev;
> >+ skb->protocol = eth_type_trans(skb, dev);
> >+#if defined(BFIN_MAC_CSUM_OFFLOAD)
> >+ skb->csum = current_rx_ptr->status.ip_payload_csum;
> >+ skb->ip_summed = CHECKSUM_PARTIAL;
> >+#endif
> >+
> >+ netif_rx(skb);
> >+ lp->stats.rx_packets++;
> >+ lp->stats.rx_bytes += len;
> >+ current_rx_ptr->status.status_word = 0x00000000;
> >+ current_rx_ptr = current_rx_ptr->next;
> >+
> >+ out:
> >+ return;
> >+}
> >+
> >+/* interrupt routine to handle rx and error signal */
> >+static irqreturn_t bf537mac_interrupt(int irq, void *dev_id)
> >+{
> >+ struct net_device *dev = dev_id;
> >+ int number = 0;
> >+
> >+ get_one_packet:
> >+ if (current_rx_ptr->status.status_word == 0) { /* no more new packet
> >received */
> >+ if (number == 0) {
> >+ if (current_rx_ptr->next->status.status_word != 0) {
> >+ current_rx_ptr = current_rx_ptr->next;
> >+ goto real_rx;
> >+ }
> >+ }
> >+ bfin_write_DMA1_IRQ_STATUS(bfin_read_DMA1_IRQ_STATUS() |
> >+ DMA_DONE | DMA_ERR);
> >+ return IRQ_HANDLED;
> >+ }
> >+
> >+ real_rx:
> >+ bf537mac_rx(dev);
> >+ number++;
> >+ goto get_one_packet;
> >+}
> >+
> >+#ifdef CONFIG_NET_POLL_CONTROLLER
> >+static void bf537mac_poll(struct net_device *dev)
> >+{
> >+ disable_irq(IRQ_MAC_RX);
> >+ bf537mac_interrupt(IRQ_MAC_RX, dev);
> >+ enable_irq(IRQ_MAC_RX);
> >+}
> >+#endif /* CONFIG_NET_POLL_CONTROLLER */
> >+
> >+static void bf537mac_reset(void)
> >+{
> >+ unsigned int opmode;
> >+
> >+ opmode = bfin_read_EMAC_OPMODE();
> >+ opmode &= (~RE);
> >+ opmode &= (~TE);
> >+ /* Turn off the EMAC */
> >+ bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() & opmode);
> >+}
> >+
> >+/*
> >+ * Enable Interrupts, Receive, and Transmit
> >+ */
> >+static int bf537mac_enable(struct net_device *dev)
> >+{
> >+ u32 opmode;
> >+
> >+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
> >+
> >+ /* Set RX DMA */
> >+ bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a));
> >+ bfin_write_DMA1_CONFIG(*
> >+ ((unsigned short
> >+ *)(&(rx_list_head->desc_a.config))));
> >+
> >+ /* Wait MII done */
> >+ poll_mdc_done();
> >+
> >+ /* We enable only RX here */
> >+ /* ASTP : Enable Automatic Pad Stripping
> >+ PR : Promiscuous Mode for test
> >+ PSF : Receive frames with total length less than 64 bytes.
> >+ FDMODE : Full Duplex Mode
> >+ LB : Internal Loopback for test
> >+ RE : Receiver Enable */
> >+ opmode = bfin_read_EMAC_OPMODE();
> >+ if (opmode & FDMODE)
> >+ opmode |= PSF;
> >+ else
> >+ opmode |= DRO | DC | PSF;
> >+ opmode |= RE;
> >+
> >+#if defined(CONFIG_BFIN_MAC_RMII)
> >+ opmode |= RMII; /* For Now only 100MBit are supported */
> >+#ifdef CONFIG_BF_REV_0_2
> >+ opmode |= TE;
> >+#endif
> >+#endif
> >+ /* Turn on the EMAC rx */
> >+ bfin_write_EMAC_OPMODE(opmode);
> >+
> >+ return 0;
> >+}
> >+
> >+/* Our watchdog timed out. Called by the networking layer */
> >+static void bf537mac_timeout(struct net_device *dev)
> >+{
> >+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
> >+
> >+ bf537mac_reset();
> >+
> >+ /* reset tx queue */
> >+ tx_list_tail = tx_list_head->next;
> >+
> >+ bf537mac_enable(dev);
> >+
> >+ /* We can accept TX packets again */
> >+ dev->trans_start = jiffies;
> >+ netif_wake_queue(dev);
> >+}
> >+
> >+/*
> >+ * Get the current statistics.
> >+ * This may be called with the card open or closed.
> >+ */
> >+static struct net_device_stats *bf537mac_query_statistics(struct net_device
> >+ *dev)
> >+{
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+
> >+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
> >+
> >+ return &lp->stats;
> >+}
> >+
> >+/*
> >+ * This routine will, depending on the values passed to it,
> >+ * either make it accept multicast packets, go into
> >+ * promiscuous mode (for TCPDUMP and cousins) or accept
> >+ * a select set of multicast packets
> >+ */
> >+static void bf537mac_set_multicast_list(struct net_device *dev)
> >+{
> >+ u32 sysctl;
> >+
> >+ if (dev->flags & IFF_PROMISC) {
> >+ printk(KERN_INFO "%s: set to promisc mode\n", dev->name);
> >+ sysctl = bfin_read_EMAC_OPMODE();
> >+ sysctl |= RAF;
> >+ bfin_write_EMAC_OPMODE(sysctl);
> >+ } else if (dev->flags & IFF_ALLMULTI || dev->mc_count > 16) {
> >+ /* accept all multicast */
> >+ sysctl = bfin_read_EMAC_OPMODE();
> >+ sysctl |= PAM;
> >+ bfin_write_EMAC_OPMODE(sysctl);
> >+ } else if (dev->mc_count) {
> >+ /* set multicast */
> >+ } else {
> >+ /* clear promisc or multicast mode */
> >+ sysctl = bfin_read_EMAC_OPMODE();
> >+ sysctl &= ~(RAF | PAM);
> >+ bfin_write_EMAC_OPMODE(sysctl);
> >+ }
> >+}
> >+
> >+/*
> >+ * this puts the device in an inactive state
> >+ */
> >+static void bf537mac_shutdown(struct net_device *dev)
> >+{
> >+ /* Turn off the EMAC */
> >+ bfin_write_EMAC_OPMODE(0x00000000);
> >+ /* Turn off the EMAC RX DMA */
> >+ bfin_write_DMA1_CONFIG(0x0000);
> >+ bfin_write_DMA2_CONFIG(0x0000);
> >+}
> >+
> >+/*
> >+ * Open and Initialize the interface
> >+ *
> >+ * Set up everything, reset the card, etc..
> >+ */
> >+static int bf537mac_open(struct net_device *dev)
> >+{
> >+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
> >+
> >+ /*
> >+ * Check that the address is valid. If its not, refuse
> >+ * to bring the device up. The user must specify an
> >+ * address using ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx
> >+ */
> >+ if (!is_valid_ether_addr(dev->dev_addr)) {
> >+ printk(KERN_WARNING CARDNAME ": no valid ethernet hw addr\n");
> >+ return -EINVAL;
> >+ }
> >+
> >+ /* initial rx and tx list */
> >+ desc_list_init();
> >+
> >+ bf537mac_setphy(dev);
> >+ setup_system_regs(dev);
> >+ bf537mac_reset();
> >+ bf537mac_enable(dev);
> >+
> >+ pr_debug("hardware init finished\n");
> >+ netif_start_queue(dev);
> >+ netif_carrier_on(dev);
> >+
> >+ return 0;
> >+}
> >+
> >+/*
> >+ *
> >+ * this makes the board clean up everything that it can
> >+ * and not talk to the outside world. Caused by
> >+ * an 'ifconfig ethX down'
> >+ */
> >+static int bf537mac_close(struct net_device *dev)
> >+{
> >+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
> >+
> >+ netif_stop_queue(dev);
> >+ netif_carrier_off(dev);
> >+
> >+ /* clear everything */
> >+ bf537mac_shutdown(dev);
> >+
> >+ /* free the rx/tx buffers */
> >+ desc_list_free();
> >+
> >+ return 0;
> >+}
> >+
> >+static int __init bf537mac_probe(struct net_device *dev)
> >+{
> >+ struct bf537mac_local *lp = netdev_priv(dev);
> >+ int retval;
> >+
> >+ /* Grab the MAC address in the MAC */
> >+ *(u32 *) (&(dev->dev_addr[0])) = bfin_read_EMAC_ADDRLO();
> >+ *(u16 *) (&(dev->dev_addr[4])) = (u16) bfin_read_EMAC_ADDRHI();
> >+
> >+/* probe mac */
> >+ /*todo: how to proble? which is revision_register */
> >+ bfin_write_EMAC_ADDRLO(0x12345678);
> >+ if (bfin_read_EMAC_ADDRLO() != 0x12345678) {
> >+ pr_debug("can't detect bf537 mac!\n");
> >+ retval = -ENODEV;
> >+ goto err_out;
> >+ }
> >+
> >+ /*Is it valid? (Did bootloader initialize it?) */
> >+ if (!is_valid_ether_addr(dev->dev_addr)) {
> >+ /* Grab the MAC from the board somehow - this is done in the
> >+ arch/blackfin/boards/bf537/boardname.c */
> >+ get_bf537_ether_addr(dev->dev_addr);
> >+ }
> >+
> >+ /* If still not valid, get a random one */
> >+ if (!is_valid_ether_addr(dev->dev_addr)) {
> >+ random_ether_addr(dev->dev_addr);
> >+ }
> >+
> >+ setup_mac_addr(dev->dev_addr);
> >+
> >+ /* Fill in the fields of the device structure with ethernet values. */
> >+ ether_setup(dev);
> >+
> >+ dev->open = bf537mac_open;
> >+ dev->stop = bf537mac_close;
> >+ dev->hard_start_xmit = bf537mac_hard_start_xmit;
> >+ dev->tx_timeout = bf537mac_timeout;
> >+ dev->get_stats = bf537mac_query_statistics;
> >+ dev->set_multicast_list = bf537mac_set_multicast_list;
> >+#if 0
> >+ dev->ethtool_ops = &bf537mac_ethtool_ops;
> >+#endif
> >+#ifdef CONFIG_NET_POLL_CONTROLLER
> >+ dev->poll_controller = bf537mac_poll;
> >+#endif
> >+
> >+ /* fill in some of the fields */
> >+ lp->version = 1;
> >+ lp->PhyAddr = 0x01;
> >+ lp->CLKIN = 25;
> >+ lp->FullDuplex = 0;
> >+ lp->Negotiate = 1;
> >+ lp->FlowControl = 0;
> >+ spin_lock_init(&lp->lock);
> >+
> >+ /* set the GPIO pins to Ethernet mode */
> >+ setup_pin_mux();
> >+
> >+ /* now, enable interrupts */
> >+ /* register irq handler */
> >+ if (request_irq
> >+ (IRQ_MAC_RX, bf537mac_interrupt, IRQF_DISABLED | IRQF_SHARED,
> >+ "BFIN537_MAC_RX", dev)) {
> >+ printk(KERN_WARNING CARDNAME
> >+ ": Unable to attach BlackFin MAC RX interrupt\n");
> >+ return -EBUSY;
> >+ }
> >+
> >+ /* Enable PHY output early */
> >+ if (!(bfin_read_VR_CTL() & PHYCLKOE))
> >+ bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
> >+
> >+ retval = register_netdev(dev);
> >+ if (retval == 0) {
> >+ /* now, print out the card info, in a short format.. */
> >+ printk(KERN_INFO "Blackfin mac net device registered\n");
> >+ }
> >+
> >+ err_out:
> >+ return retval;
> >+}
> >+
> >+static int bfin_mac_probe(struct platform_device *pdev)
> >+{
> >+ struct net_device *ndev;
> >+
> >+ ndev = alloc_etherdev(sizeof(struct bf537mac_local));
> >+
> >+ if (!ndev) {
> >+ printk(KERN_WARNING CARDNAME ": could not allocate device\n");
> >+ return -ENOMEM;
> >+ }
> >+
> >+ if (bf537mac_probe(ndev) != 0) {
> >+ platform_set_drvdata(pdev, NULL);
> >+ free_netdev(ndev);
> >+ printk(KERN_WARNING CARDNAME ": not found\n");
> >+ return -ENODEV;
> >+ }
> >+
> >+ SET_MODULE_OWNER(ndev);
> >+ SET_NETDEV_DEV(ndev, &pdev->dev);
> >+
> >+ platform_set_drvdata(pdev, ndev);
> >+
> >+ return 0;
> >+}
> >+
> >+static int bfin_mac_remove(struct platform_device *pdev)
> >+{
> >+ struct net_device *ndev = platform_get_drvdata(pdev);
> >+
> >+ platform_set_drvdata(pdev, NULL);
> >+
> >+ unregister_netdev(ndev);
> >+
> >+ free_irq(IRQ_MAC_RX, ndev);
> >+
> >+ free_netdev(ndev);
> >+
> >+ return 0;
> >+}
> >+
> >+static int bfin_mac_suspend(struct platform_device *pdev, pm_message_t
> >state)
> >+{
> >+ return 0;
> >+}
> >+
> >+static int bfin_mac_resume(struct platform_device *pdev)
> >+{
> >+ return 0;
> >+}
> >+
> >+static struct platform_driver bfin_mac_driver = {
> >+ .probe = bfin_mac_probe,
> >+ .remove = bfin_mac_remove,
> >+ .resume = bfin_mac_resume,
> >+ .suspend = bfin_mac_suspend,
> >+ .driver = {
> >+ .name = CARDNAME,
> >+ },
> >+};
> >+
> >+static int __init bfin_mac_init(void)
> >+{
> >+ return platform_driver_register(&bfin_mac_driver);
> >+}
> >+
> >+module_init(bfin_mac_init);
> >+
> >+static void __exit bfin_mac_cleanup(void)
> >+{
> >+ platform_driver_unregister(&bfin_mac_driver);
> >+}
> >+
> >+module_exit(bfin_mac_cleanup);
> >diff -puN /dev/null drivers/net/bfin_mac.h
> >--- /dev/null
> >+++ a/drivers/net/bfin_mac.h
> >@@ -0,0 +1,147 @@
> >+/*
> >+ * File: drivers/net/bfin_mac.h
> >+ * Based on:
> >+ * Author: Luke Yang <[EMAIL PROTECTED]>
> >+ *
> >+ * Created:
> >+ * Description:
> >+ *
> >+ * Modified:
> >+ * Copyright 2004-2006 Analog Devices Inc.
> >+ *
> >+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
> >+ *
> >+ * This program is free software ; you can redistribute it and/or modify
> >+ * it under the terms of the GNU General Public License as published by
> >+ * the Free Software Foundation ; either version 2, or (at your option)
> >+ * any later version.
> >+ *
> >+ * This program is distributed in the hope that it will be useful,
> >+ * but WITHOUT ANY WARRANTY ; without even the implied warranty of
> >+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >+ * GNU General Public License for more details.
> >+ *
> >+ * You should have received a copy of the GNU General Public License
> >+ * along with this program ; see the file COPYING.
> >+ * If not, write to the Free Software Foundation,
> >+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
> >+ */
> >+
> >+/*
> >+ * PHY REGISTER NAMES
> >+ */
> >+#define PHYREG_MODECTL 0x0000
> >+#define PHYREG_MODESTAT 0x0001
> >+#define PHYREG_PHYID1 0x0002
> >+#define PHYREG_PHYID2 0x0003
> >+#define PHYREG_ANAR 0x0004
> >+#define PHYREG_ANLPAR 0x0005
> >+#define PHYREG_ANER 0x0006
> >+#define PHYREG_NSR 0x0010
> >+#define PHYREG_LBREMR 0x0011
> >+#define PHYREG_REC 0x0012
> >+#define PHYREG_10CFG 0x0013
> >+#define PHYREG_PHY1_1 0x0014
> >+#define PHYREG_PHY1_2 0x0015
> >+#define PHYREG_PHY2 0x0016
> >+#define PHYREG_TW_1 0x0017
> >+#define PHYREG_TW_2 0x0018
> >+#define PHYREG_TEST 0x0019
> >+
> >+#define PHY_RESET 0x8000
> >+#define PHY_ANEG_EN 0x1000
> >+#define PHY_DUPLEX 0x0100
> >+#define PHY_SPD_SET 0x2000
> >+
> >+#define BFIN_MAC_CSUM_OFFLOAD
> >+
> >+typedef struct _DMA_CONFIG {
> >+ unsigned short b_DMA_EN:1; /* Bit 0 : DMA Enable */
> >+ unsigned short b_WNR:1; /* Bit 1 : DMA Direction */
> >+ unsigned short b_WDSIZE:2; /* Bit 2 & 3 : DMA Tranfer Word size */
> >+ unsigned short b_DMA2D:1; /* Bit 4 : DMA Mode 2D or 1D */
> >+ unsigned short b_RESTART:1; /* Bit 5 : Retain the FIFO */
> >+ unsigned short b_DI_SEL:1; /* Bit 6 : Data Interrupt Timing Select
> >*/
> >+ unsigned short b_DI_EN:1; /* Bit 7 : Data Interrupt Enable */
> >+ unsigned short b_NDSIZE:4; /* Bit 8 to 11 : Flex descriptor Size */
> >+ unsigned short b_FLOW:3; /* Bit 12 to 14 : FLOW */
> >+} DMA_CONFIG_REG;
> >+
> >+struct dma_descriptor {
> >+ struct dma_descriptor *next_dma_desc;
> >+ unsigned long start_addr;
> >+ DMA_CONFIG_REG config;
> >+ unsigned short x_count;
> >+};
> >+
> >+#if 0
> >+struct status_area {
> >+ unsigned short ip_hdr_chksum; /* the IP header checksum */
> >+ unsigned short ip_payload_chksum; /* the IP header and payload
> >checksum */
> >+ unsigned long status_word; /* the frame status word */
> >+};
> >+#endif
> >+
> >+struct status_area_rx {
> >+#if defined(BFIN_MAC_CSUM_OFFLOAD)
> >+ unsigned short ip_hdr_csum; /* ip header checksum */
> >+ unsigned short ip_payload_csum; /* ip payload(udp or tcp or others)
> >checksum */
> >+#endif
> >+ unsigned long status_word; /* the frame status word */
> >+};
> >+
> >+struct status_area_tx {
> >+ unsigned long status_word; /* the frame status word */
> >+};
> >+
> >+/* use two descriptors for a packet */
> >+struct net_dma_desc_rx {
> >+ struct net_dma_desc_rx *next;
> >+ struct sk_buff *skb;
> >+ struct dma_descriptor desc_a;
> >+ struct dma_descriptor desc_b;
> >+ volatile struct status_area_rx status;
> >+};
> >+
> >+/* use two descriptors for a packet */
> >+struct net_dma_desc_tx {
> >+ struct net_dma_desc_tx *next;
> >+ struct sk_buff *skb;
> >+ struct dma_descriptor desc_a;
> >+ struct dma_descriptor desc_b;
> >+ volatile unsigned char packet[1560];
> >+ volatile struct status_area_tx status;
> >+};
> >+
> >+struct bf537mac_local {
> >+ /*
> >+ * these are things that the kernel wants me to keep, so users
> >+ * can find out semi-useless statistics of how well the card is
> >+ * performing
> >+ */
> >+ struct net_device_stats stats;
> >+
> >+ int version;
> >+
> >+ int FlowEnabled; /* record if data flow is active */
> >+ int EtherIntIVG; /* IVG for the ethernet interrupt */
> >+ int RXIVG; /* IVG for the RX completion */
> >+ int TXIVG; /* IVG for the TX completion */
> >+ int PhyAddr; /* PHY address */
> >+ int OpMode; /* set these bits n the OPMODE regs */
> >+ int Port10; /* set port speed to 10 Mbit/s */
> >+ int GenChksums; /* IP checksums to be calculated */
> >+ int NoRcveLnth; /* dont insert recv length at start of buffer */
> >+ int StripPads; /* remove trailing pad bytes */
> >+ int FullDuplex; /* set full duplex mode */
> >+ int Negotiate; /* enable auto negotiation */
> >+ int Loopback; /* loopback at the PHY */
> >+ int Cache; /* Buffers may be cached */
> >+ int FlowControl; /* flow control active */
> >+ int CLKIN; /* clock in value in MHZ */
> >+ unsigned short IntMask; /* interrupt mask */
> >+ unsigned char Mac[6]; /* MAC address of the board */
> >+ spinlock_t lock;
> >+};
> >+
> >+extern void get_bf537_ether_addr(char *addr);
> >_
> >-
> >To unsubscribe from this list: send the line "unsubscribe netdev" in
> >the body of a message to [EMAIL PROTECTED]
> >More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
> >
> >
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
