Hi Mark,
Networking stuff generally goes to netdev. [ Added to Cc: ]
On 6/21/07, Mark Hannessen <[EMAIL PROTECTED]> wrote:
Hi list,
I have some trouble getting my network card to run.
when I run dmesg I can clearly see it being detected
eth0: VIA Rhine II at 0xee006000, 00:e0:c5:54:88:a8, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
but when I try ifconfig eth0 up it fails with a no device error.
SIOCSIFADDR: No such device eth0:
ERROR while getting interface flags: No such device
I tried adding pci=routeirq too, but that didn't work either.
I know there is nothing wrong with the card itself because it works on
the linux distro that came with it.
does anyone have any hints as to what might get it up and running?
Thanks!
Mark
I attached a complete dmesg output just in case..
00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:09.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623
[Apollo CLE266] integrated CastleRock graphics (rev 03)
Linux version 2.6.20.14 ([EMAIL PROTECTED]) (gcc version 4.1.1 (Gentoo
4.1.1-r3)) #2 PREEMPT Thu Jun 21 09:11:50 CEST 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end:
000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end:
00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end:
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001f6f0000 end:
000000001f7f0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001f7f0000 size: 0000000000003000 end:
000000001f7f3000 type: 4
copy_e820_map() start: 000000001f7f3000 size: 000000000000d000 end:
000000001f800000 type: 3
copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end:
0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f7f0000 (usable)
BIOS-e820: 000000001f7f0000 - 000000001f7f3000 (ACPI NVS)
BIOS-e820: 000000001f7f3000 - 000000001f800000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
503MB LOWMEM available.
Entering add_active_range(0, 0, 129008) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 129008
early_node_map[1] active PFN ranges
0: 0 -> 129008
On node 0 totalpages: 129008
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 975 pages used for memmap
Normal zone: 123937 pages, LIFO batch:31
DMI 2.2 present.
ACPI: RSDP (v000 CLE266 ) @ 0x000f6690
ACPI: RSDT (v001 CLE266 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1f7f3040
ACPI: FADT (v001 CLE266 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1f7f30c0
ACPI: DSDT (v001 CLE266 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 20000000 (gap: 1f800000:e07f0000)
Detected 1000.450 MHz processor.
Built 1 zonelists. Total pages: 128001
Kernel command line: BOOT_IMAGE=(hd0,1)/kernels/vmlinuz-2.6.20
root=/dev/sda2 splash=silent,fadein,tty=tty8,theme:riecom console=tty1
vga=791 pci=routeirq
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 500536k/516032k available (2425k kernel code, 14860k reserved,
1369k data, 168k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffff7000 - 0xfffff000 ( 32 kB)
vmalloc : 0xe0000000 - 0xffff5000 ( 511 MB)
lowmem : 0xc0000000 - 0xdf7f0000 ( 503 MB)
.init : 0xc04b8000 - 0xc04e2000 ( 168 kB)
.data : 0xc035e41c - 0xc04b4a10 (1369 kB)
.text : 0xc0100000 - 0xc035e41c (2425 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2002.29 BogoMIPS (lpj=1001145)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0381b03f 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000
00000000 000000dd 00000000
Compat vDSO mapped to ffffe000.
CPU: Centaur VIA Nehemiah stepping 08
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 9a20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 5000-500f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *15
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 *12)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 12 (level,
low) -> IRQ 12
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ec000000-edffffff
PREFETCH window: e8000000-ebffffff
PCI: Bus 2, cardbus bridge: 0000:00:09.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-23ffffff
MEM window: 24000000-27ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6248k freed
audit: initializing netlink socket (disabled)
audit(1182410582.259:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered (default)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
VIA RNG detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
vesafb: framebuffer at 0xe8000000, mapped to 0xe0080000, using 3072k,
total 8192k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:352c
vesafb: pmi: set display start = c00c357a, set palette = c00c35eb
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 0
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (29 C)
ibm_acpi: ec object not found
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
PCI: VIA VLink IRQ fixup for 0000:00:12.0, from 15 to 11
eth0: VIA Rhine II at 0xee006000, 00:e0:c5:54:88:a8, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
PCI: VIA VLink IRQ fixup for 0000:00:11.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
SCSI Media Changer driver v0.25
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 12 (level,
low) -> IRQ 12
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 12, io mem 0xee005000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
PCI: VIA VLink IRQ fixup for 0000:00:10.0, from 15 to 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 3
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
PCI: VIA VLink IRQ fixup for 0000:00:10.1, from 5 to 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000e500
usb 1-6: configuration #1 chosen from 1 choice
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
input: Logitech Logitech USB Keyboard as /class/input/input3
input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on
usb-0000:00:10.2-1
input: Logitech Logitech USB Keyboard as /class/input/input4
input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on
usb-0000:00:10.2-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded
padlock: No VIA PadLock drivers have been loaded.
padlock: Using VIA PadLock ACE for AES algorithm.
padlock: VIA PadLock Hash Engine not detected.
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[EMAIL PROTECTED]>
All bugs added by David S. Miller <[EMAIL PROTECTED]>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
Using IPI Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 168k freed
scsi 0:0:0:0: Direct-Access BUFFALO USB Flash Disk 4000 PQ: 0 ANSI: 0 CCS
SCSI device sda: 16056320 512-byte hdwr sectors (8221 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 16056320 512-byte hdwr sectors (8221 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
Time: acpi_pm clocksource has been installed.
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:11.5 to 64
ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
ReiserFS: dm-0: using ordered data mode
ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: dm-0: checking transaction log (dm-0)
ReiserFS: dm-0: Using r5 hash to sort names
fbsplash: console 1 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'riecom'
fbsplash: switched splash state to 'on' on console 5
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
