The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olte...@gmail.com>
Signed-off-by: Florian Fainelli <f.faine...@gmail.com>
---
drivers/net/ethernet/broadcom/tg3.c | 6 ------
include/linux/brcmphy.h | 9 +++------
2 files changed, 3 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/tg3.c
b/drivers/net/ethernet/broadcom/tg3.c
index 8936c2bc6286..d2381929931b 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -1580,12 +1580,6 @@ static int tg3_mdio_init(struct tg3 *tp)
PHY_BRCM_RX_REFCLK_UNUSED |
PHY_BRCM_DIS_TXCRXC_NOENRGY |
PHY_BRCM_AUTO_PWRDWN_ENABLE;
- if (tg3_flag(tp, RGMII_INBAND_DISABLE))
- phydev->dev_flags |= PHY_BRCM_STD_IBND_DISABLE;
- if (tg3_flag(tp, RGMII_EXT_IBND_RX_EN))
- phydev->dev_flags |= PHY_BRCM_EXT_IBND_RX_ENABLE;
- if (tg3_flag(tp, RGMII_EXT_IBND_TX_EN))
- phydev->dev_flags |= PHY_BRCM_EXT_IBND_TX_ENABLE;
fallthrough;
case PHY_ID_RTL8211C:
phydev->interface = PHY_INTERFACE_MODE_RGMII;
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 16597d3fa011..8fe1d55371ac 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -63,12 +63,9 @@
#define PHY_BRCM_AUTO_PWRDWN_ENABLE 0x00000001
#define PHY_BRCM_RX_REFCLK_UNUSED 0x00000002
-#define PHY_BRCM_STD_IBND_DISABLE 0x00000004
-#define PHY_BRCM_EXT_IBND_RX_ENABLE 0x00000008
-#define PHY_BRCM_EXT_IBND_TX_ENABLE 0x00000010
-#define PHY_BRCM_CLEAR_RGMII_MODE 0x00000020
-#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00000040
-#define PHY_BRCM_EN_MASTER_MODE 0x00000080
+#define PHY_BRCM_CLEAR_RGMII_MODE 0x00000004
+#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00000008
+#define PHY_BRCM_EN_MASTER_MODE 0x00000010
/* Broadcom BCM7xxx specific workarounds */
#define PHY_BRCM_7XXX_REV(x) (((x) >> 8) & 0xff)
--
2.25.1
