On Tue, 8 May 2007, Chris Stromsoe wrote:
On Mon, 12 Mar 2007, Chris Stromsoe wrote:
On Thu, 8 Mar 2007, Chris Stromsoe wrote:
On Thu, 8 Mar 2007, Jay Vosburgh wrote:
Chris Stromsoe <[EMAIL PROTECTED]> wrote:
1) ip link set mtu 9000 eth2 <-- eth2 is no longer responsive
ip link set mtu 1500 eth2 <-- eth2 remains unresponsive
2) ifup eth2
ifdown eth2
perl -pi -e 's/eth2/eth3/' /etc/network/interfaces
ifup eth3 <-- locks up here
This would seem to suggest a problem with skge itself, although there
might be some other interaction with bonding that causes the problems for
that case.
In both of the above mentioned cases, I was not using bonding. That was
with the skge driver only.
The above tests both work fine with the 2.6.20.1 sk98lin driver loaded as
"modprobe sk98lin RlmtMode=DualNet".
I can change the MTU, add and remove eth2/eth3 from the bond, and up and
down the interface. It also works fine with different hardware (e100,
e1000, tg3, bnx2). Running both interfaces alone without the bonding
driver also works (I can up and down the interfaces with no side-affects).
Just an update - it looks like 2.6.20.1 fixed the MTU problem ("1" above),
but not the other problem (where the machine locks up if the second port on
the dual-port card is downed).
To recap:
I am use SysKonnect SK-9843 cards. The sk98lin driver works fine; the skge
I should proof-read first. The cards are SK-9844s, not SK-9843s. The
rest of the prior message is still correct.
-Chris
driver does not. The following sequence of commands locks up the server.
The lock is a hard lock; console is not responsive to keyboard input or to
sysrq. Nothing is printed on the serial console.
ip li set eth2 up
ip li set eth2 down
ip li set eth3 up
There are no addresses assigned to either interface. This was done after a
fresh boot. It is repeatable. If I do not down eth2, I can up eth3 assign
addresses, and use both interfaces.
The kernel is fresh from kernel.org and does not have any third party
patches.
lspci -vv output:
0000:01:0a.0 Ethernet controller: Syskonnect (Schneider & Koch) SK-98xx
Gigabit Ethernet Server Adapter (rev 12)
Subsystem: Syskonnect (Schneider & Koch) SK-9844 Gigabit Ethernet
Server Adapter (SK-NET GE-SX dual link)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ff8fc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d800 [size=256]
Expansion ROM at ff400000 [disabled] [size=128K]
Capabilities: <available only to root>
-Chris
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
