It is desirable to define the HCI packet payload sizes of
USB alternate settings so that they can be exposed to user
space.
Reviewed-by: Alain Michaud <ala...@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpan...@chromium.org>
Signed-off-by: Joseph Hwang <joseph...@chromium.org>
---
drivers/bluetooth/btusb.c | 43 ++++++++++++++++++++++++--------
include/net/bluetooth/hci_core.h | 1 +
2 files changed, 33 insertions(+), 11 deletions(-)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 8d2608ddfd0875..df7cadf6385868 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -459,6 +459,22 @@ static const struct dmi_system_id
btusb_needs_reset_resume_table[] = {
#define BTUSB_WAKEUP_DISABLE 14
#define BTUSB_USE_ALT1_FOR_WBS 15
+/* Per core spec 5, vol 4, part B, table 2.1,
+ * list the hci packet payload sizes for various ALT settings.
+ * This is used to set the packet length for the wideband speech.
+ * If a controller does not probe its usb alt setting, the default
+ * value will be 0. Any clients at upper layers should interpret it
+ * as a default value and set a proper packet length accordingly.
+ *
+ * To calculate the HCI packet payload length:
+ * for alternate settings 1 - 5:
+ * hci_packet_size = suggested_max_packet_size * 3 (packets) -
+ * 3 (HCI header octets)
+ * for alternate setting 6:
+ * hci_packet_size = suggested_max_packet_size - 3 (HCI header octets)
+ */
+static const int hci_packet_size_usb_alt[] = { 0, 24, 48, 72, 96, 144, 60 };
+
struct btusb_data {
struct hci_dev *hdev;
struct usb_device *udev;
@@ -3958,6 +3974,15 @@ static int btusb_probe(struct usb_interface *intf,
hdev->notify = btusb_notify;
hdev->prevent_wake = btusb_prevent_wake;
+ if (id->driver_info & BTUSB_AMP) {
+ /* AMP controllers do not support SCO packets */
+ data->isoc = NULL;
+ } else {
+ /* Interface orders are hardcoded in the specification */
+ data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
+ data->isoc_ifnum = ifnum_base + 1;
+ }
+
#ifdef CONFIG_PM
err = btusb_config_oob_wake(hdev);
if (err)
@@ -4021,6 +4046,10 @@ static int btusb_probe(struct usb_interface *intf,
hdev->set_diag = btintel_set_diag;
hdev->set_bdaddr = btintel_set_bdaddr;
hdev->cmd_timeout = btusb_intel_cmd_timeout;
+
+ if (btusb_find_altsetting(data, 6))
+ hdev->sco_pkt_len = hci_packet_size_usb_alt[6];
+
set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
@@ -4062,15 +4091,6 @@ static int btusb_probe(struct usb_interface *intf,
btusb_check_needs_reset_resume(intf);
}
- if (id->driver_info & BTUSB_AMP) {
- /* AMP controllers do not support SCO packets */
- data->isoc = NULL;
- } else {
- /* Interface orders are hardcoded in the specification */
- data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
- data->isoc_ifnum = ifnum_base + 1;
- }
-
if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
(id->driver_info & BTUSB_REALTEK)) {
hdev->setup = btrtl_setup_realtek;
@@ -4082,9 +4102,10 @@ static int btusb_probe(struct usb_interface *intf,
* (DEVICE_REMOTE_WAKEUP)
*/
set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
- if (btusb_find_altsetting(data, 1))
+ if (btusb_find_altsetting(data, 1)) {
set_bit(BTUSB_USE_ALT1_FOR_WBS, &data->flags);
- else
+ hdev->sco_pkt_len = hci_packet_size_usb_alt[1];
+ } else
bt_dev_err(hdev, "Device does not support ALT setting
1");
}
diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index 8caac20556b499..0624496328fc09 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -417,6 +417,7 @@ struct hci_dev {
unsigned int acl_pkts;
unsigned int sco_pkts;
unsigned int le_pkts;
+ unsigned int sco_pkt_len;
__u16 block_len;
__u16 block_mtu;
--
2.28.0.236.gb10cc79966-goog
