The ksz8873 and ksz8863 switches are affected by following errata:
| "Receiver error in 100BASE-TX mode following Soft Power Down"
|
| Some KSZ8873 devices may exhibit receiver errors after transitioning
| from Soft Power Down mode to Normal mode, as controlled by register 195
| (0xC3) bits [1:0]. When exiting Soft Power Down mode, the receiver
| blocks may not start up properly, causing the PHY to miss data and
| exhibit erratic behavior. The problem may appear on either port 1 or
| port 2, or both ports. The problem occurs only for 100BASE-TX, not
| 10BASE-T.
|
| END USER IMPLICATIONS
| When the failure occurs, the following symptoms are seen on the affected
| port(s):
| - The port is able to link
| - LED0 blinks, even when there is no traffic
| - The MIB counters indicate receive errors (Rx Fragments, Rx Symbol
| Errors, Rx CRC Errors, Rx Alignment Errors)
| - Only a small fraction of packets is correctly received and forwarded
| through the switch. Most packets are dropped due to receive errors.
|
| The failing condition cannot be corrected by the following:
| - Removing and reconnecting the cable
| - Hardware reset
| - Software Reset and PCS Reset bits in register 67 (0x43)
|
| Work around:
| The problem can be corrected by setting and then clearing the Port Power
| Down bits (registers 29 (0x1D) and 45 (0x2D), bit 3). This must be done
| separately for each affected port after returning from Soft Power Down
| Mode to Normal Mode. The following procedure will ensure no further
| issues due to this erratum. To enter Soft Power Down Mode, set register
| 195 (0xC3), bits [1:0] = 10.
|
| To exit Soft Power Down Mode, follow these steps:
| 1. Set register 195 (0xC3), bits [1:0] = 00 // Exit soft power down mode
| 2. Wait 1ms minimum
| 3. Set register 29 (0x1D), bit [3] = 1 // Enter PHY port 1 power down mode
| 4. Set register 29 (0x1D), bit [3] = 0 // Exit PHY port 1 power down mode
| 5. Set register 45 (0x2D), bit [3] = 1 // Enter PHY port 2 power down mode
| 6. Set register 45 (0x2D), bit [3] = 0 // Exit PHY port 2 power down mode
This patch implements steps 2...6 of the suggested workaround. The first
step needs to be implemented in the switch driver.
Signed-off-by: Oleksij Rempel <o.rem...@pengutronix.de>
---
drivers/net/phy/micrel.c | 22 +++++++++++++++++++++-
1 file changed, 21 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index caf56b9b51db..12106fbea565 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -1010,6 +1010,26 @@ static int ksz8873mll_config_aneg(struct phy_device
*phydev)
return 0;
}
+static int ksz886x_resume(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Apply errata workaround for KSZ8863 and KSZ8873:
+ * Receiver error in 100BASE-TX mode following Soft Power Down
+ *
+ * When exiting Soft Power Down mode, the receiver blocks may not start
+ * up properly, causing the PHY to miss data and exhibit erratic
+ * behavior.
+ */
+ usleep_range(1000, 2000);
+
+ ret = phy_set_bits(phydev, MII_BMCR, BMCR_PDOWN);
+ if (ret)
+ return ret;
+
+ return phy_clear_bits(phydev, MII_BMCR, BMCR_PDOWN);
+}
+
static int kszphy_get_sset_count(struct phy_device *phydev)
{
return ARRAY_SIZE(kszphy_hw_stats);
@@ -1347,7 +1367,7 @@ static struct phy_driver ksphy_driver[] = {
/* PHY_BASIC_FEATURES */
.config_init = kszphy_config_init,
.suspend = genphy_suspend,
- .resume = genphy_resume,
+ .resume = ksz886x_resume,
}, {
.name = "Micrel KSZ87XX Switch",
/* PHY_BASIC_FEATURES */
--
2.27.0
