On Thu, Aug 08, 2019 at 09:02:57AM +0000, Jose Abreu wrote: > From: Russell King - ARM Linux admin <li...@armlinux.org.uk> > Date: Aug/08/2019, 09:26:26 (UTC+00:00) > > > Hi, > > > > Have you tried enabling debug mode in phylink (add #define DEBUG at the > > top of the file) ? > > Yes: > > [ With > 2.5G modes removed ] > # dmesg | grep -i phy > libphy: stmmac: probed > stmmaceth 0000:04:00.0 enp4s0: PHY [stmmac-1:00] driver [Synopsys 10G] > stmmaceth 0000:04:00.0 enp4s0: phy: setting supported > 00,00000000,0002e040 advertising 00,00000000,0002e040 > stmmaceth 0000:04:00.0 enp4s0: configuring for phy/usxgmii link mode > stmmaceth 0000:04:00.0 enp4s0: phylink_mac_config: > mode=phy/usxgmii/Unknown/Unknown adv=00,00000000,0002e040 pause=10 > link=0 an=1 > stmmaceth 0000:04:00.0 enp4s0: phy link down usxgmii/Unknown/Unknown
This shows that the PHY isn't reporting that the link came up. Did the PHY negotiate link? If so, why isn't it reporting that the link came up? Maybe something is mis-programming the capability bits in the PHY? Maybe disabling the 10G speeds disables everything faster than 1G? > [ Without any limit ] > # dmesg | grep -i phy > libphy: stmmac: probed > stmmaceth 0000:04:00.0 enp4s0: PHY [stmmac-1:00] driver [Synopsys 10G] > stmmaceth 0000:04:00.0 enp4s0: phy: setting supported > 00,00000000,000ee040 advertising 00,00000000,000ee040 > stmmaceth 0000:04:00.0 enp4s0: configuring for phy/usxgmii link mode > stmmaceth 0000:04:00.0 enp4s0: phylink_mac_config: > mode=phy/usxgmii/Unknown/Unknown adv=00,00000000,000ee040 pause=10 > link=0 an=1 > stmmaceth 0000:04:00.0 enp4s0: phy link down usxgmii/Unknown/Unknown > stmmaceth 0000:04:00.0 enp4s0: phy link up usxgmii/2.5Gbps/Full > stmmaceth 0000:04:00.0 enp4s0: phylink_mac_config: > mode=phy/usxgmii/2.5Gbps/Full adv=00,00000000,00000000 pause=0f link=1 > an=0 > > I'm thinking on whether this can be related with USXGMII. As link is > operating in 10G but I configure USXGMII for 2.5G maybe autoneg outcome > should always be 10G ? As I understand USXGMII (which isn't very well, because the spec isn't available) I believe that it operates in a similar way to SGMII where data is replicated the appropriate number of times to achieve the link speed. So, the USXGMII link always operates at a bit rate equivalent to 10G, but data is replicated twice for 5G, four times for 2.5G, ten times for 1G, etc. I notice that you don't say that you support any copper speeds, which brings up the question about what the PHY's media is... > > On Thu, Aug 08, 2019 at 08:17:29AM +0000, Jose Abreu wrote: > > > ++ PHY Experts > > > > > > From: Jose Abreu <joab...@synopsys.com> > > > Date: Aug/07/2019, 16:46:23 (UTC+00:00) > > > > > > > Hello, > > > > > > > > I've some sample code for Clause 73 support using Synopsys based XPCS > > > > but I would like to clarify some things that I noticed. > > > > > > > > I'm using USXGMII as interface and a single SERDES that operates at 10G > > > > rate but MAC side is working at 2.5G. Maximum available bandwidth is > > > > therefore 2.5Gbps. > > > > > > > > So, I configure USXGMII for 2.5G mode and it works but if I try to > > > > limit > > > > the autoneg abilities to 2.5G max then it never finishes: > > > > # ethtool enp4s0 > > > > Settings for enp4s0: > > > > Supported ports: [ ] > > > > Supported link modes: 1000baseKX/Full > > > > 2500baseX/Full > > > > Supported pause frame use: Symmetric Receive-only > > > > Supports auto-negotiation: Yes > > > > Supported FEC modes: Not reported > > > > Advertised link modes: 1000baseKX/Full > > > > 2500baseX/Full > > > > Advertised pause frame use: Symmetric Receive-only > > > > Advertised auto-negotiation: Yes > > > > Advertised FEC modes: Not reported > > > > Speed: Unknown! > > > > Duplex: Unknown! (255) > > > > Port: MII > > > > PHYAD: 0 > > > > Transceiver: internal > > > > Auto-negotiation: on > > > > Supports Wake-on: ug > > > > Wake-on: d > > > > Current message level: 0x0000003f (63) > > > > drv probe link timer ifdown ifup > > > > Link detected: no > > > > > > > > When I do not limit autoneg and I say that maximum limit is 10G then I > > > > get Link Up and autoneg finishes with this outcome: > > > > # ethtool enp4s0 > > > > Settings for enp4s0: > > > > Supported ports: [ ] > > > > Supported link modes: 1000baseKX/Full > > > > 2500baseX/Full > > > > 10000baseKX4/Full > > > > 10000baseKR/Full > > > > Supported pause frame use: Symmetric Receive-only > > > > Supports auto-negotiation: Yes > > > > Supported FEC modes: Not reported > > > > Advertised link modes: 1000baseKX/Full > > > > 2500baseX/Full > > > > 10000baseKX4/Full > > > > 10000baseKR/Full > > > > Advertised pause frame use: Symmetric Receive-only > > > > Advertised auto-negotiation: Yes > > > > Advertised FEC modes: Not reported > > > > Link partner advertised link modes: 1000baseKX/Full > > > > 2500baseX/Full > > > > 10000baseKX4/Full > > > > 10000baseKR/Full > > > > Link partner advertised pause frame use: Symmetric Receive-only > > > > Link partner advertised auto-negotiation: Yes > > > > Link partner advertised FEC modes: Not reported > > > > Speed: 2500Mb/s > > > > Duplex: Full > > > > Port: MII <- Never mind this, it's a SW issue > > > > PHYAD: 0 > > > > Transceiver: internal > > > > Auto-negotiation: on > > > > Supports Wake-on: ug > > > > Wake-on: d > > > > Current message level: 0x0000003f (63) > > > > drv probe link timer ifdown ifup > > > > Link detected: yes > > > > > > > > I was expecting that, as MAC side is limited to 2.5G, I should set in > > > > phylink the correct capabilities and then outcome of autoneg would only > > > > have up to 2.5G modes. Am I wrong ? > > > > > > > > --- > > > > Thanks, > > > > Jose Miguel Abreu > > > > > > > > > --- > > > Thanks, > > > Jose Miguel Abreu > > > > > > > -- > > RMK's Patch system: > > https://urldefense.proofpoint.com/v2/url?u=https-3A__www.armlinux.org.uk_developer_patches_&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=WHDsc6kcWAl4i96Vm5hJ_19IJiuxx_p_Rzo2g-uHDKw&m=1MdSlPrmzsMMCJbbLcDYTNuPq1njfusBRjcRz3UD4Dg&s=_30hwSYkGf9DfyCG48mnh7lXP8iiULXpfAP_6agUJno&e= > > > > FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps > > up > > According to speedtest.net: 11.9Mbps down 500kbps up > > > --- > Thanks, > Jose Miguel Abreu > -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
