On 2019/06/17 16:48, Benjamin Poirier wrote:
> qlge uses an irq enable/disable refcounting scheme that is:
> * poorly implemented
> Uses a spin_lock to protect accesses to the irq_cnt atomic variable
> * buggy
> Breaks when there is not a 1:1 sequence of irq - napi_poll, such as
> when using SO_BUSY_POLL.
> * unnecessary
> The purpose or irq_cnt is to reduce irq control writes when
> multiple work items result from one irq: the irq is re-enabled
> after all work is done.
> Analysis of the irq handler shows that there is only one case where
> there might be two workers scheduled at once, and those have
> separate irq masking bits.
>
> Therefore, remove irq_cnt.
>
> Additionally, we get a performance improvement:
> perf stat -e cycles -a -r5 super_netperf 100 -H 192.168.33.1 -t TCP_RR
>
> Before:
> 628560
> 628056
> 622103
> 622744
> 627202
> [...]
> 268,803,947,669 cycles ( +- 0.09% )
>
> After:
> 636300
> 634106
> 634984
> 638555
> 634188
> [...]
> 259,237,291,449 cycles ( +- 0.19% )
>
> Signed-off-by: Benjamin Poirier <bpoir...@suse.com>
David, Greg,
Before I send v2 of this patchset, how about moving this driver out to
staging? The hardware has been declared EOL by the vendor but what's
more relevant to the Linux kernel is that the quality of this driver is
not on par with many other mainline drivers, IMO. Over in staging, the
code might benefit from the attention of interested parties (drive-by
fixers) or fade away into obscurity.
Now that I check, the code has >500 basic checkpatch issues. While
working on the rx processing code for the current patchset, I noticed
the following more structural issues:
* commit 7c734359d350 ("qlge: Size RX buffers based on MTU.",
v2.6.33-rc1) introduced dead code in the receive routines, which
should be rewritten anyways by the admission of the author himself
(see the comment above ql_build_rx_skb())
* truesize accounting is incorrect (ex: a 9000B frame has truesize 10280
while containing two frags of order-1 allocations, ie. >16K)
* in some cases the driver allocates skbs with head room but only puts
data in the frags
* there is an inordinate amount of disparate debugging code, most of
which is of questionable value. In particular, qlge_dbg.c has hundreds
of lines of code bitrotting away in ifdef land (doesn't compile since
commit 18c49b91777c ("qlge: do vlan cleanup", v3.1-rc1), 8 years ago).
* triggering an ethtool regdump will instead hexdump a 176k struct to
dmesg depending on some module parameters
* many structures are defined full of holes, as we found in this
thread already; are used inefficiently (struct rx_ring is used for rx
and tx completions, with some members relevant to one case only); are
initialized redundantly (ex. memset 0 after alloc_etherdev). The
driver also has a habit of using runtime checks where compile time
checks are possible.
* in terms of namespace, the driver uses either qlge_, ql_ (used by
other qlogic drivers, with clashes, ex: ql_sem_spinlock) or nothing (with
clashes, ex: struct ob_mac_iocb_req)
I'm guessing other parts of the driver have more issues of the same
nature. The driver also has many smaller issues like deprecated apis,
duplicate or useless comments, weird code structure (some "while" loops
that could be rewritten with simple "for", ex. ql_wait_reg_rdy()) and
weird line wrapping (all over, ex. the ql_set_routing_reg() calls in
qlge_set_multicast_list()).
I'm aware of some precedents for code moving from mainline to staging:
1bb8155080c6 ncpfs: move net/ncpfs to drivers/staging/ncpfs (v4.16-rc1)
6c391ff758eb irda: move drivers/net/irda to drivers/staging/irda/drivers
(v4.14-rc1)
What do you think is the best course of action in this case?
Thanks,
-Benjamin
