Using Vinicius Costa Gomes' configuration interface for 802.1Qbv (later resent by Voon Weifeng for the stmmac driver), I am submitting for review a draft implementation of this offload for a DSA switch.
I don't want to insist too much on the hardware specifics of SJA1105 which isn't otherwise very compliant to the IEEE spec. In order to be able to test with Vedang Patel's iproute2 patch for taprio offload (https://www.spinics.net/lists/netdev/msg573072.html) I had to actually revert the txtime-assist branch as it had changed the iproute2 interface. In terms of impact for DSA drivers, I would like to point out that: - Maybe somebody should pre-populate qopt->cycle_time in case the user does not provide one. Otherwise each driver needs to iterate over the GCL once, just to set the cycle time (right now stmmac does as well). - Configuring the switch over SPI cannot apparently be done from this ndo_setup_tc callback because it runs in atomic context. I also have some downstream patches to offload tc clsact matchall with mirred action, but in that case it looks like the atomic context restriction does not apply. - I had to copy the struct tc_taprio_qopt_offload to driver private memory because a static config needs to be constructed every time a change takes place, and there are up to 4 switch ports that may take a TAS configuration. I have created a private tc_taprio_qopt_offload_copy() helper for this - I don't know whether it's of any help in the general case. There is more to be done however. The TAS needs to be integrated with the PTP driver. This is because with a PTP clock source, the base time is written dynamically to the PTPSCHTM (PTP schedule time) register and must be a time in the future. Then the "real" base time of each port's TAS config can be offset by at most ~50 ms (the DELTA field from the Schedule Entry Points Table) relative to PTPSCHTM. Because base times in the past are completely ignored by this hardware, we need to decide if it's ok behaviorally for a driver to "roll" a past base time into the immediate future by incrementally adding the cycle time (so the phase doesn't change). If it is, then decide by how long in the future it is ok to do so. Or alternatively, is it preferable if the driver errors out if the user-supplied base time is in the past and the hardware doesn't like it? But even then, there might be fringe cases when the base time becomes a past PTP time right as the driver tries to apply the config. Also applying a tc-taprio offload to a second SJA1105 switch port will inevitably need to roll the first port's (now past) base time into an equivalent future time. All of this is going to be complicated even further by the fact that resetting the switch (to apply the tc-taprio offload) makes it reset its PTP time. Vinicius Costa Gomes (1): taprio: Add support for hardware offloading Vladimir Oltean (5): Revert "Merge branch 'net-sched-Add-txtime-assist-support-for-taprio'" net: dsa: Pass tc-taprio offload to drivers net: dsa: sja1105: Add static config tables for scheduling net: dsa: sja1105: Advertise the 8 TX queues net: dsa: sja1105: Configure the Time-Aware Shaper via tc-taprio offload drivers/net/dsa/sja1105/Kconfig | 8 + drivers/net/dsa/sja1105/Makefile | 4 + drivers/net/dsa/sja1105/sja1105.h | 6 + .../net/dsa/sja1105/sja1105_dynamic_config.c | 8 + drivers/net/dsa/sja1105/sja1105_main.c | 19 +- .../net/dsa/sja1105/sja1105_static_config.c | 167 +++++ .../net/dsa/sja1105/sja1105_static_config.h | 48 +- drivers/net/dsa/sja1105/sja1105_tas.c | 452 ++++++++++++ drivers/net/dsa/sja1105/sja1105_tas.h | 22 + drivers/net/ethernet/intel/igb/igb_main.c | 1 - include/linux/netdevice.h | 1 + include/net/dsa.h | 3 + include/net/pkt_sched.h | 18 + include/uapi/linux/pkt_sched.h | 11 +- net/dsa/slave.c | 14 + net/dsa/tag_sja1105.c | 3 +- net/sched/sch_etf.c | 10 - net/sched/sch_taprio.c | 666 ++++++++---------- 18 files changed, 1060 insertions(+), 401 deletions(-) create mode 100644 drivers/net/dsa/sja1105/sja1105_tas.c create mode 100644 drivers/net/dsa/sja1105/sja1105_tas.h -- 2.17.1
