Hi,
On Mon, Jun 24, 2019 at 04:52:47PM +0200, René van Dorst wrote:
> Convert mt7530 to PHYLINK API
>
> Signed-off-by: René van Dorst <opensou...@vdorst.com>
> ---
> drivers/net/dsa/mt7530.c | 237 +++++++++++++++++++++++++++++----------
> drivers/net/dsa/mt7530.h | 9 ++
> 2 files changed, 187 insertions(+), 59 deletions(-)
>
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index 3181e95586d6..9c5e4dd00826 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -13,7 +13,7 @@
> #include <linux/of_mdio.h>
> #include <linux/of_net.h>
> #include <linux/of_platform.h>
> -#include <linux/phy.h>
> +#include <linux/phylink.h>
> #include <linux/regmap.h>
> #include <linux/regulator/consumer.h>
> #include <linux/reset.h>
> @@ -633,63 +633,6 @@ mt7530_get_sset_count(struct dsa_switch *ds, int port,
> int sset)
> return ARRAY_SIZE(mt7530_mib);
> }
>
> -static void mt7530_adjust_link(struct dsa_switch *ds, int port,
> - struct phy_device *phydev)
> -{
> - struct mt7530_priv *priv = ds->priv;
> -
> - if (phy_is_pseudo_fixed_link(phydev)) {
> - dev_dbg(priv->dev, "phy-mode for master device = %x\n",
> - phydev->interface);
> -
> - /* Setup TX circuit incluing relevant PAD and driving */
> - mt7530_pad_clk_setup(ds, phydev->interface);
> -
> - if (priv->id == ID_MT7530) {
> - /* Setup RX circuit, relevant PAD and driving on the
> - * host which must be placed after the setup on the
> - * device side is all finished.
> - */
> - mt7623_pad_clk_setup(ds);
> - }
> - } else {
> - u16 lcl_adv = 0, rmt_adv = 0;
> - u8 flowctrl;
> - u32 mcr = PMCR_USERP_LINK | PMCR_FORCE_MODE;
> -
> - switch (phydev->speed) {
> - case SPEED_1000:
> - mcr |= PMCR_FORCE_SPEED_1000;
> - break;
> - case SPEED_100:
> - mcr |= PMCR_FORCE_SPEED_100;
> - break;
> - }
> -
> - if (phydev->link)
> - mcr |= PMCR_FORCE_LNK;
> -
> - if (phydev->duplex) {
> - mcr |= PMCR_FORCE_FDX;
> -
> - if (phydev->pause)
> - rmt_adv = LPA_PAUSE_CAP;
> - if (phydev->asym_pause)
> - rmt_adv |= LPA_PAUSE_ASYM;
> -
> - lcl_adv = linkmode_adv_to_lcl_adv_t(
> - phydev->advertising);
> - flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
> -
> - if (flowctrl & FLOW_CTRL_TX)
> - mcr |= PMCR_TX_FC_EN;
> - if (flowctrl & FLOW_CTRL_RX)
> - mcr |= PMCR_RX_FC_EN;
> - }
> - mt7530_write(priv, MT7530_PMCR_P(port), mcr);
> - }
> -}
> -
> static int
> mt7530_cpu_port_enable(struct mt7530_priv *priv,
> int port)
> @@ -1323,6 +1266,178 @@ mt7530_setup(struct dsa_switch *ds)
> return 0;
> }
>
> +static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
> + unsigned int mode,
> + const struct phylink_link_state *state)
> +{
> + struct mt7530_priv *priv = ds->priv;
> + u32 mcr = PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
> + PMCR_BACKPR_EN | PMCR_TX_EN | PMCR_RX_EN;
> +
> + switch (port) {
> + case 0: /* Internal phy */
> + case 1:
> + case 2:
> + case 3:
> + case 4:
> + if (state->interface != PHY_INTERFACE_MODE_GMII)
> + goto unsupported;
> + break;
> + /* case 5: Port 5 is not supported! */
> + case 6: /* 1st cpu port */
> + if (state->interface != PHY_INTERFACE_MODE_RGMII &&
> + state->interface != PHY_INTERFACE_MODE_TRGMII)
> + goto unsupported;
> +
> + /* Setup TX circuit incluing relevant PAD and driving */
> + mt7530_pad_clk_setup(ds, state->interface);
> +
> + if (priv->id == ID_MT7530) {
> + /* Setup RX circuit, relevant PAD and driving on the
> + * host which must be placed after the setup on the
> + * device side is all finished.
> + */
> + mt7623_pad_clk_setup(ds);
> + }
> + break;
> + default:
> + dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
> + return;
> + }
> +
> + if (!state->an_enabled || mode == MLO_AN_FIXED) {
> + mcr |= PMCR_FORCE_MODE;
> +
> + if (state->speed == SPEED_1000)
> + mcr |= PMCR_FORCE_SPEED_1000;
> + if (state->speed == SPEED_100)
> + mcr |= PMCR_FORCE_SPEED_100;
> + if (state->duplex == DUPLEX_FULL)
> + mcr |= PMCR_FORCE_FDX;
> + if (state->link || mode == MLO_AN_FIXED)
> + mcr |= PMCR_FORCE_LNK;
This should be removed - state->link is not for use in mac_config.
Even in fixed mode, the link can be brought up/down by means of a
gpio, and this should be dealt with via the mac_link_* functions.
> + if (state->pause || phylink_test(state->advertising, Pause))
> + mcr |= PMCR_TX_FC_EN | PMCR_RX_FC_EN;
> + if (state->pause & MLO_PAUSE_TX)
> + mcr |= PMCR_TX_FC_EN;
> + if (state->pause & MLO_PAUSE_RX)
> + mcr |= PMCR_RX_FC_EN;
This is clearly wrong - if any bit in state->pause is set, then we
end up with both PMCR_TX_FC_EN | PMCR_RX_FC_EN set. If we have Pause
Pause set in the advertising mask, then both are set. This doesn't
seem right - are these bits setting the advertisement, or are they
telling the MAC to use flow control?
> + }
> +
> + mt7530_write(priv, MT7530_PMCR_P(port), mcr);
> +
> + return;
> +
> +unsupported:
> + dev_err(ds->dev, "%s: P%d: Unsupported phy_interface mode: %d (%s)\n",
> + __func__, port, state->interface, phy_modes(state->interface));
> +}
> +
> +static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
> + unsigned int mode,
> + phy_interface_t interface)
> +{
> + /* Do nothing */
> +}
> +
> +static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
> + unsigned int mode,
> + phy_interface_t interface,
> + struct phy_device *phydev)
> +{
> + /* Do nothing */
> +}
These two are where you should be forcing the link up or down if
required (basically, inband modes should let the link come up/down
irrespective of these functions, otherwise it should be forced.)
> +
> +static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
> + unsigned long *supported,
> + struct phylink_link_state *state)
> +{
> + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +
> + switch (port) {
> + case 0: /* Internal phy */
> + case 1:
> + case 2:
> + case 3:
> + case 4:
> + if (state->interface != PHY_INTERFACE_MODE_NA &&
> + state->interface != PHY_INTERFACE_MODE_GMII)
> + goto unsupported;
> + break;
> + /* case 5: Port 5 not supported! */
> + case 6: /* 1st cpu port */
> + if (state->interface != PHY_INTERFACE_MODE_RGMII &&
> + state->interface != PHY_INTERFACE_MODE_TRGMII)
PHY_INTERFACE_MODE_NA ?
> + goto unsupported;
> + break;
> + default:
> + linkmode_zero(supported);
> + dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
> + return;
> + }
> +
> + phylink_set(mask, Autoneg);
> + phylink_set(mask, Pause);
> + phylink_set(mask, Asym_Pause);
> + phylink_set(mask, MII);
> +
> + phylink_set(mask, 10baseT_Half);
> + phylink_set(mask, 10baseT_Full);
> + phylink_set(mask, 100baseT_Half);
> + phylink_set(mask, 100baseT_Full);
> + phylink_set(mask, 1000baseT_Full);
> + phylink_set(mask, 1000baseT_Half);
You seem to be missing phylink_set_port_modes() here.
> +
> + linkmode_and(supported, supported, mask);
> + linkmode_and(state->advertising, state->advertising, mask);
> + return;
> +
> +unsupported:
> + linkmode_zero(supported);
> + dev_err(ds->dev, "%s: unsupported interface mode: [0x%x] %s\n",
> + __func__, state->interface, phy_modes(state->interface));
Not a good idea to print this at error level; sometimes we just probe
for support.
Eg, think about a SFP cage, and a SFP is plugged in that uses a PHY
interface mode that the MAC can't support - we detect that by the
validation failing, and printing a more meaningful message in phylink
itself.
> +}
> +
> +static int
> +mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
> + struct phylink_link_state *state)
> +{
> + struct mt7530_priv *priv = ds->priv;
> + u32 pmsr;
> +
> + if (port < 0 || port >= MT7530_NUM_PORTS)
> + return -EINVAL;
> +
> + pmsr = mt7530_read(priv, MT7530_PMSR_P(port));
> +
> + state->link = (pmsr & PMSR_LINK);
> + state->an_complete = state->link;
> + state->duplex = (pmsr & PMSR_DPX) >> 1;
> +
> + switch (pmsr & (PMSR_SPEED_1000 | PMSR_SPEED_100)) {
> + case 0:
> + state->speed = SPEED_10;
> + break;
> + case PMSR_SPEED_100:
> + state->speed = SPEED_100;
> + break;
> + case PMSR_SPEED_1000:
> + state->speed = SPEED_1000;
> + break;
> + default:
> + state->speed = SPEED_UNKNOWN;
> + break;
> + }
> +
> + state->pause = 0;
> + if (pmsr & PMSR_RX_FC)
> + state->pause |= MLO_PAUSE_RX;
> + if (pmsr & PMSR_TX_FC)
> + state->pause |= MLO_PAUSE_TX;
> +
> + return 1;
> +}
> +
> static const struct dsa_switch_ops mt7530_switch_ops = {
> .get_tag_protocol = mtk_get_tag_protocol,
> .setup = mt7530_setup,
> @@ -1331,7 +1446,6 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
> .phy_write = mt7530_phy_write,
> .get_ethtool_stats = mt7530_get_ethtool_stats,
> .get_sset_count = mt7530_get_sset_count,
> - .adjust_link = mt7530_adjust_link,
> .port_enable = mt7530_port_enable,
> .port_disable = mt7530_port_disable,
> .port_stp_state_set = mt7530_stp_state_set,
> @@ -1344,6 +1458,11 @@ static const struct dsa_switch_ops mt7530_switch_ops =
> {
> .port_vlan_prepare = mt7530_port_vlan_prepare,
> .port_vlan_add = mt7530_port_vlan_add,
> .port_vlan_del = mt7530_port_vlan_del,
> + .phylink_validate = mt7530_phylink_validate,
> + .phylink_mac_link_state = mt7530_phylink_mac_link_state,
> + .phylink_mac_config = mt7530_phylink_mac_config,
> + .phylink_mac_link_down = mt7530_phylink_mac_link_down,
> + .phylink_mac_link_up = mt7530_phylink_mac_link_up,
> };
>
> static const struct of_device_id mt7530_of_match[] = {
> diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
> index bfac90f48102..41d9a132ac70 100644
> --- a/drivers/net/dsa/mt7530.h
> +++ b/drivers/net/dsa/mt7530.h
> @@ -198,6 +198,7 @@ enum mt7530_vlan_port_attr {
> #define PMCR_FORCE_SPEED_100 BIT(2)
> #define PMCR_FORCE_FDX BIT(1)
> #define PMCR_FORCE_LNK BIT(0)
> +#define PMCR_FORCE_LNK_DOWN PMCR_FORCE_MODE
> #define PMCR_COMMON_LINK (PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
> PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
> PMCR_TX_EN | PMCR_RX_EN | \
> @@ -218,6 +219,14 @@ enum mt7530_vlan_port_attr {
> PMCR_TX_FC_EN | PMCR_RX_FC_EN)
>
> #define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100)
> +#define PMSR_EEE1G BIT(7)
> +#define PMSR_EEE100M BIT(6)
> +#define PMSR_RX_FC BIT(5)
> +#define PMSR_TX_FC BIT(4)
> +#define PMSR_SPEED_1000 BIT(3)
> +#define PMSR_SPEED_100 BIT(2)
> +#define PMSR_DPX BIT(1)
> +#define PMSR_LINK BIT(0)
>
> /* Register for MIB */
> #define MT7530_PORT_MIB_COUNTER(x) (0x4000 + (x) * 0x100)
> --
> 2.20.1
>
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
