This series contains updates to the i40e driver only. Björn improves retpoline enabled builds by replacing the expensive switch statements with 'if' statements that acts on the XDP program result.
Carolyn changes the driver behavior to now disable the VF after one MDD event instead of allowing a couple of MDD events before doing the reset. Aleksandr changes the driver to only report an error when a VF tries to remove VLAN when a port VLAN is configured, unless it is VLAN 0. Also extends the LLDP support to be able to keep the current LLDP state persistent across a power cycle. Maciej fixes the checksum calculation due to firmware changes, which requires the driver to perform a double shadow RAM dump in some cases. Adam adds advertising support for 40GBase_LR4, 40GBase_CR4 and fibre in the driver. Jake cleans up a check that is not needed and was producing a warning in GCC 8. Harshitha fixes a misleading message by ensuring that a success message is only printed on the host side when the promiscuous mode change has been successful. Stefan Assmann adds the vendor id and device id to the dmesg log entry during probe to help with bug reports when lspci output may not be available. Alice and Piotr add recovery mode support in the i40e driver, which is needed for migrating from a structured to a flat firmware image. The following are changes since commit 88d6272acaaa4bfb03da0a87a8754ec431471680: net: phy: avoid unneeded MDIO reads in genphy_read_status and are available in the git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue 40GbE Adam Ludkiewicz (1): i40e: Report advertised link modes on 40GBase_LR4, CR4 and fibre Aleksandr Loktionov (2): i40e: remove error msg when vf with port vlan tries to remove vlan 0 i40e: Further implementation of LLDP Alice Michael (2): i40e: update version number i40e: Introduce recovery mode support Björn Töpel (1): i40e: replace switch-statement to speed-up retpoline-enabled builds Carolyn Wyborny (2): i40e: Fix for allowing too many MDD events on VF i40e: change behavior on PF in response to MDD event Harshitha Ramamurthy (1): i40e: fix misleading message about promisc setting on un-trusted VF Jacob Keller (1): i40e: remove out-of-range comparisons in i40e_validate_cloud_filter Maciej Paczkowski (1): i40e: ShadowRAM checksum calculation change Stefan Assmann (1): i40e: print PCI vendor and device ID during probe drivers/net/ethernet/intel/i40e/i40e.h | 1 + drivers/net/ethernet/intel/i40e/i40e_adminq.c | 5 + .../net/ethernet/intel/i40e/i40e_adminq_cmd.h | 20 +- drivers/net/ethernet/intel/i40e/i40e_common.c | 62 ++- .../net/ethernet/intel/i40e/i40e_debugfs.c | 4 +- .../net/ethernet/intel/i40e/i40e_ethtool.c | 28 +- drivers/net/ethernet/intel/i40e/i40e_main.c | 352 +++++++++++++++--- drivers/net/ethernet/intel/i40e/i40e_nvm.c | 29 +- .../net/ethernet/intel/i40e/i40e_prototype.h | 8 +- drivers/net/ethernet/intel/i40e/i40e_txrx.c | 32 +- .../ethernet/intel/i40e/i40e_txrx_common.h | 27 ++ drivers/net/ethernet/intel/i40e/i40e_type.h | 1 + .../ethernet/intel/i40e/i40e_virtchnl_pf.c | 35 +- drivers/net/ethernet/intel/i40e/i40e_xsk.c | 24 +- 14 files changed, 498 insertions(+), 130 deletions(-) -- 2.20.1
