On 07/02/19 9:49 PM, Russell King wrote:
> Add support for the Armada 38x common phy to allow us to change the
> speed of the Ethernet serdes lane. This driver only supports
> manipulation of the speed, it does not support configuration of the
> common phy.
>
> Signed-off-by: Russell King <rmk+ker...@armlinux.org.uk>
This patch will conflict with PHY pull request (in the marvell Kconfig and
Makefile). But the resolution should be trivial and should be okay to go via
-net tree.
FWIW
Acked-by: Kishon Vijay Abraham I <kis...@ti.com>
> ---
> drivers/phy/marvell/Kconfig | 10 ++
> drivers/phy/marvell/Makefile | 1 +
> drivers/phy/marvell/phy-armada38x-comphy.c | 237
> +++++++++++++++++++++++++++++
> 3 files changed, 248 insertions(+)
> create mode 100644 drivers/phy/marvell/phy-armada38x-comphy.c
>
> diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
> index 6fb4b56e4c14..224ea4e6a46d 100644
> --- a/drivers/phy/marvell/Kconfig
> +++ b/drivers/phy/marvell/Kconfig
> @@ -21,6 +21,16 @@ config PHY_BERLIN_USB
> help
> Enable this to support the USB PHY on Marvell Berlin SoCs.
>
> +config PHY_MVEBU_A38X_COMPHY
> + tristate "Marvell Armada 38x comphy driver"
> + depends on ARCH_MVEBU || COMPILE_TEST
> + depends on OF
> + select GENERIC_PHY
> + help
> + This driver allows to control the comphy, an hardware block providing
> + shared serdes PHYs on Marvell Armada 38x. Its serdes lanes can be
> + used by various controllers (Ethernet, sata, usb, PCIe...).
> +
> config PHY_MVEBU_CP110_COMPHY
> tristate "Marvell CP110 comphy driver"
> depends on ARCH_MVEBU || COMPILE_TEST
> diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
> index 3975b144f8ec..59b6c03ef756 100644
> --- a/drivers/phy/marvell/Makefile
> +++ b/drivers/phy/marvell/Makefile
> @@ -2,6 +2,7 @@
> obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o
> obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
> obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
> +obj-$(CONFIG_PHY_MVEBU_A38X_COMPHY) += phy-armada38x-comphy.o
> obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY) += phy-mvebu-cp110-comphy.o
> obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
> obj-$(CONFIG_PHY_PXA_28NM_HSIC) += phy-pxa-28nm-hsic.o
> diff --git a/drivers/phy/marvell/phy-armada38x-comphy.c
> b/drivers/phy/marvell/phy-armada38x-comphy.c
> new file mode 100644
> index 000000000000..3e00bc679d4e
> --- /dev/null
> +++ b/drivers/phy/marvell/phy-armada38x-comphy.c
> @@ -0,0 +1,237 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Russell King, Deep Blue Solutions Ltd.
> + *
> + * Partly derived from CP110 comphy driver by Antoine Tenart
> + * <antoine.ten...@bootlin.com>
> + */
> +#include <linux/delay.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/phy.h>
> +#include <linux/platform_device.h>
> +
> +#define MAX_A38X_COMPHY 6
> +#define MAX_A38X_PORTS 3
> +
> +#define COMPHY_CFG1 0x00
> +#define COMPHY_CFG1_GEN_TX(x) ((x) << 26)
> +#define COMPHY_CFG1_GEN_TX_MSK COMPHY_CFG1_GEN_TX(15)
> +#define COMPHY_CFG1_GEN_RX(x) ((x) << 22)
> +#define COMPHY_CFG1_GEN_RX_MSK COMPHY_CFG1_GEN_RX(15)
> +#define GEN_SGMII_1_25GBPS 6
> +#define GEN_SGMII_3_125GBPS 8
> +
> +#define COMPHY_STAT1 0x18
> +#define COMPHY_STAT1_PLL_RDY_TX BIT(3)
> +#define COMPHY_STAT1_PLL_RDY_RX BIT(2)
> +
> +#define COMPHY_SELECTOR 0xfc
> +
> +struct a38x_comphy;
> +
> +struct a38x_comphy_lane {
> + void __iomem *base;
> + struct a38x_comphy *priv;
> + unsigned int n;
> +
> + int port;
> +};
> +
> +struct a38x_comphy {
> + void __iomem *base;
> + struct device *dev;
> + struct a38x_comphy_lane lane[MAX_A38X_COMPHY];
> +};
> +
> +static const u8 gbe_mux[MAX_A38X_COMPHY][MAX_A38X_PORTS] = {
> + { 0, 0, 0 },
> + { 4, 5, 0 },
> + { 0, 4, 0 },
> + { 0, 0, 4 },
> + { 0, 3, 0 },
> + { 0, 0, 3 },
> +};
> +
> +static void a38x_comphy_set_reg(struct a38x_comphy_lane *lane,
> + unsigned int offset, u32 mask, u32 value)
> +{
> + u32 val;
> +
> + val = readl_relaxed(lane->base + offset) & ~mask;
> + writel(val | value, lane->base + offset);
> +}
> +
> +static void a38x_comphy_set_speed(struct a38x_comphy_lane *lane,
> + unsigned int gen_tx, unsigned int gen_rx)
> +{
> + a38x_comphy_set_reg(lane, COMPHY_CFG1,
> + COMPHY_CFG1_GEN_TX_MSK | COMPHY_CFG1_GEN_RX_MSK,
> + COMPHY_CFG1_GEN_TX(gen_tx) |
> + COMPHY_CFG1_GEN_RX(gen_rx));
> +}
> +
> +static int a38x_comphy_poll(struct a38x_comphy_lane *lane,
> + unsigned int offset, u32 mask, u32 value)
> +{
> + u32 val;
> + int ret;
> +
> + ret = readl_relaxed_poll_timeout_atomic(lane->base + offset, val,
> + (val & mask) == value,
> + 1000, 150000);
> +
> + if (ret)
> + dev_err(lane->priv->dev,
> + "comphy%u: timed out waiting for status\n", lane->n);
> +
> + return ret;
> +}
> +
> +/*
> + * We only support changing the speed for comphys configured for GBE.
> + * Since that is all we do, we only poll for PLL ready status.
> + */
> +static int a38x_comphy_set_mode(struct phy *phy, enum phy_mode mode, int sub)
> +{
> + struct a38x_comphy_lane *lane = phy_get_drvdata(phy);
> + unsigned int gen;
> +
> + if (mode != PHY_MODE_ETHERNET)
> + return -EINVAL;
> +
> + switch (sub) {
> + case PHY_INTERFACE_MODE_SGMII:
> + case PHY_INTERFACE_MODE_1000BASEX:
> + gen = GEN_SGMII_1_25GBPS;
> + break;
> +
> + case PHY_INTERFACE_MODE_2500BASEX:
> + gen = GEN_SGMII_3_125GBPS;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + a38x_comphy_set_speed(lane, gen, gen);
> +
> + return a38x_comphy_poll(lane, COMPHY_STAT1,
> + COMPHY_STAT1_PLL_RDY_TX |
> + COMPHY_STAT1_PLL_RDY_RX,
> + COMPHY_STAT1_PLL_RDY_TX |
> + COMPHY_STAT1_PLL_RDY_RX);
> +}
> +
> +static const struct phy_ops a38x_comphy_ops = {
> + .set_mode = a38x_comphy_set_mode,
> + .owner = THIS_MODULE,
> +};
> +
> +static struct phy *a38x_comphy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct a38x_comphy_lane *lane;
> + struct phy *phy;
> + u32 val;
> +
> + if (WARN_ON(args->args[0] >= MAX_A38X_PORTS))
> + return ERR_PTR(-EINVAL);
> +
> + phy = of_phy_simple_xlate(dev, args);
> + if (IS_ERR(phy))
> + return phy;
> +
> + lane = phy_get_drvdata(phy);
> + if (lane->port >= 0)
> + return ERR_PTR(-EBUSY);
> +
> + lane->port = args->args[0];
> +
> + val = readl_relaxed(lane->priv->base + COMPHY_SELECTOR);
> + val = (val >> (4 * lane->n)) & 0xf;
> +
> + if (!gbe_mux[lane->n][lane->port] ||
> + val != gbe_mux[lane->n][lane->port]) {
> + dev_warn(lane->priv->dev,
> + "comphy%u: not configured for GBE\n", lane->n);
> + phy = ERR_PTR(-EINVAL);
> + }
> +
> + return phy;
> +}
> +
> +static int a38x_comphy_probe(struct platform_device *pdev)
> +{
> + struct phy_provider *provider;
> + struct device_node *child;
> + struct a38x_comphy *priv;
> + struct resource *res;
> + void __iomem *base;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + priv->dev = &pdev->dev;
> + priv->base = base;
> +
> + for_each_available_child_of_node(pdev->dev.of_node, child) {
> + struct phy *phy;
> + int ret;
> + u32 val;
> +
> + ret = of_property_read_u32(child, "reg", &val);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
> + ret);
> + continue;
> + }
> +
> + if (val >= MAX_A38X_COMPHY || priv->lane[val].base) {
> + dev_err(&pdev->dev, "invalid 'reg' property\n");
> + continue;
> + }
> +
> + phy = devm_phy_create(&pdev->dev, child, &a38x_comphy_ops);
> + if (IS_ERR(phy))
> + return PTR_ERR(phy);
> +
> + priv->lane[val].base = base + 0x28 * val;
> + priv->lane[val].priv = priv;
> + priv->lane[val].n = val;
> + priv->lane[val].port = -1;
> + phy_set_drvdata(phy, &priv->lane[val]);
> + }
> +
> + dev_set_drvdata(&pdev->dev, priv);
> +
> + provider = devm_of_phy_provider_register(&pdev->dev, a38x_comphy_xlate);
> +
> + return PTR_ERR_OR_ZERO(provider);
> +}
> +
> +static const struct of_device_id a38x_comphy_of_match_table[] = {
> + { .compatible = "marvell,armada-380-comphy" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, a38x_comphy_of_match_table);
> +
> +static struct platform_driver a38x_comphy_driver = {
> + .probe = a38x_comphy_probe,
> + .driver = {
> + .name = "armada-38x-comphy",
> + .of_match_table = a38x_comphy_of_match_table,
> + },
> +};
> +module_platform_driver(a38x_comphy_driver);
> +
> +MODULE_AUTHOR("Russell King <rmk+ker...@armlinux.org.uk>");
> +MODULE_DESCRIPTION("Common PHY driver for Armada 38x SoCs");
> +MODULE_LICENSE("GPL v2");
>
