On Wed, Jan 16, 2019 at 06:37:49PM +0000, Fabrizio Castro wrote:
> From: Biju Das <biju....@bp.renesas.com>
>
> This patch adds uSD card support.
Can I confirm that SDHI0 is wired up to a uSD slot?
I ask because if that is the case then this patch looks good to me.
But if it is wired up to a full-size SD slot then I believe
a wp-gpio (write protect) should be described.
>
> Signed-off-by: Biju Das <biju....@bp.renesas.com>
> Reviewed-by: Fabrizio Castro <fabrizio.cas...@bp.renesas.com>
> Reviewed-by: Chris Paterson <chris.paters...@renesas.com>
> ---
> arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts | 50
> +++++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
> b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
> index c545ce5..477a56b 100644
> --- a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
> +++ b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
> @@ -7,6 +7,7 @@
>
> /dts-v1/;
> #include "r8a774c0.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> model = "Silicon Linux RZ/G2E 96board platform (CAT874)";
> @@ -26,6 +27,29 @@
> /* first 128MB is reserved for secure area. */
> reg = <0x0 0x48000000 0x0 0x78000000>;
> };
> +
> + vcc_sdhi0: regulator-vcc-sdhi0 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "SDHI0 Vcc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vccq_sdhi0: regulator-vccq-sdhi0 {
> + compatible = "regulator-gpio";
> +
> + regulator-name = "SDHI0 VccQ";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <3300000 1
> + 1800000 0>;
> + };
> };
>
> &extal_clk {
> @@ -37,6 +61,18 @@
> groups = "scif2_data_a";
> function = "scif2";
> };
> +
> + sdhi0_pins: sd0 {
> + groups = "sdhi0_data4", "sdhi0_ctrl";
> + function = "sdhi0";
> + power-source = <3300>;
> + };
> +
> + sdhi0_pins_uhs: sd0_uhs {
> + groups = "sdhi0_data4", "sdhi0_ctrl";
> + function = "sdhi0";
> + power-source = <1800>;
> + };
> };
>
> &scif2 {
> @@ -45,3 +81,17 @@
>
> status = "okay";
> };
> +
> +&sdhi0 {
> + pinctrl-0 = <&sdhi0_pins>;
> + pinctrl-1 = <&sdhi0_pins_uhs>;
> + pinctrl-names = "default", "state_uhs";
> +
> + vmmc-supply = <&vcc_sdhi0>;
> + vqmmc-supply = <&vccq_sdhi0>;
> + cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> --
> 2.7.4
>
