- In CXGB4_DCB_STATE_FW_INCOMPLETE state check if the dcb
version is changed and update the dcb supported version.
- Also, fill the priority code point value for priority
based flow control.
Signed-off-by: Ganesh Goudar <ganes...@chelsio.com>
---
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c | 27 ++++++++++++++++++++++++++
drivers/net/ethernet/chelsio/cxgb4/l2t.c | 6 ++++--
2 files changed, 31 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c
b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c
index b34f0f0..6ba3104 100644
--- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c
+++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c
@@ -114,6 +114,24 @@ void cxgb4_dcb_reset(struct net_device *dev)
cxgb4_dcb_state_init(dev);
}
+/* update the dcb port support, if version is IEEE then set it to
+ * FW_PORT_DCB_VER_IEEE and if DCB_CAP_DCBX_VER_CEE is already set then
+ * clear that. and if it is set to CEE then set dcb supported to
+ * DCB_CAP_DCBX_VER_CEE & if DCB_CAP_DCBX_VER_IEEE is set, clear it
+ */
+static inline void cxgb4_dcb_update_support(struct port_dcb_info *dcb)
+{
+ if (dcb->dcb_version == FW_PORT_DCB_VER_IEEE) {
+ if (dcb->supported & DCB_CAP_DCBX_VER_CEE)
+ dcb->supported &= ~DCB_CAP_DCBX_VER_CEE;
+ dcb->supported |= DCB_CAP_DCBX_VER_IEEE;
+ } else if (dcb->dcb_version == FW_PORT_DCB_VER_CEE1D01) {
+ if (dcb->supported & DCB_CAP_DCBX_VER_IEEE)
+ dcb->supported &= ~DCB_CAP_DCBX_VER_IEEE;
+ dcb->supported |= DCB_CAP_DCBX_VER_CEE;
+ }
+}
+
/* Finite State machine for Data Center Bridging.
*/
void cxgb4_dcb_state_fsm(struct net_device *dev,
@@ -165,6 +183,15 @@ void cxgb4_dcb_state_fsm(struct net_device *dev,
}
case CXGB4_DCB_STATE_FW_INCOMPLETE: {
+ if (transition_to != CXGB4_DCB_INPUT_FW_DISABLED) {
+ /* during this CXGB4_DCB_STATE_FW_INCOMPLETE state,
+ * check if the dcb version is changed (there can be
+ * mismatch in default config & the negotiated switch
+ * configuration at FW, so update the dcb support
+ * accordingly.
+ */
+ cxgb4_dcb_update_support(dcb);
+ }
switch (transition_to) {
case CXGB4_DCB_INPUT_FW_ENABLED: {
/* we're alreaady in firmware DCB mode */
diff --git a/drivers/net/ethernet/chelsio/cxgb4/l2t.c
b/drivers/net/ethernet/chelsio/cxgb4/l2t.c
index 301c4df..99022c0 100644
--- a/drivers/net/ethernet/chelsio/cxgb4/l2t.c
+++ b/drivers/net/ethernet/chelsio/cxgb4/l2t.c
@@ -433,10 +433,12 @@ struct l2t_entry *cxgb4_l2t_get(struct l2t_data *d,
struct neighbour *neigh,
else
lport = netdev2pinfo(physdev)->lport;
- if (is_vlan_dev(neigh->dev))
+ if (is_vlan_dev(neigh->dev)) {
vlan = vlan_dev_vlan_id(neigh->dev);
- else
+ vlan |= vlan_dev_get_egress_qos_mask(neigh->dev, priority);
+ } else {
vlan = VLAN_NONE;
+ }
write_lock_bh(&d->lock);
for (e = d->l2tab[hash].first; e; e = e->next)
--
2.1.0
