Ganesh:
On 6/4/18 9:03 AM, AMG Zollner Robert wrote:
> I have noticed that vrf is not working with kernel v4.15.0 but was
> working with v4.13.0 when using cxgb4 Chelsio driver (T520-cr)
>
> Setup:
> Two metal servers with a T520-cr card each, directly connected without a
> switch in between.
>
> SVR1 only ipfwd SVR2 with vrf
> .----------------------------. .----------------------------------.
> | | | |
> | 192.168.8.1 [ ens2f4]--|---------|--[ens1f4] 192.168.8.2 |
> | 192.168.9.1 [ens2f4d1]--|---------|--<ens1f4d1> 192.168.9.2 VRF=10 |
> `----------------------------' `----------------------------------'
>
> When vrf is not working there are no error messages (dmesg or iproute
> commands), tcpdump on the interface (SVR2.ens1f4d1) enslaved in vrf 10
> shows packets(arp req/reply) coming in and going out, but outgoing
> packets(arp reply) do not reach the other server SVR1.ens2f4d1
>
>
> Bisect:
> Found this commit to be the problem after doing a git bisect between
> v4.13..v4.15:
>
> commit ba581f77df23c8ee70b372966e69cf10bc5453d8
> Author: Ganesh Goudar <ganes...@chelsio.com>
> Date: Sat Sep 23 16:07:28 2017 +0530
>
> cxgb4: do DCB state reset in couple of places
>
> reset the driver's DCB state in couple of places
> where it was missing.
Are you working on a fix for this or should a revert of the above patch
be sent?
>
>
> A bisect step was considered good when:
> - successful ping from SVR1 to SVR2.ens1f4d1 vrf interface
> - successful ping from SVR2 global to SVR2 vrf interface trough SVR1(l3
> forwarding) (this check was redundant,both tests fail or pass simultaneous)
>
> The problem is still present on recent kernels also, checked v4.16.0 and
> v4.17.rc7
>
> Disabling DCB for the card support fixes the problem ( Compiling kernel
> with "CONFIG_CHELSIO_T4_DCB=n")
>
>
>
> This is my first time reporting a bug to the linux kernel and hope I
> have included the right amount of information. Please let me know if I
> have missed something.
>
>
>
> Thank you,
> Zollner Robert
>
>
> --------
> Logs:
>
> VRF configured using folowing commands:
>
> #!/bin/sh
>
> CHDEV=ens1f4
> VRF=vrf-recv
>
> sysctl -w net.ipv4.tcp_l3mdev_accept=1
> sysctl -w net.ipv4.udp_l3mdev_accept=1
> sysctl -w net.ipv4.conf.all.accept_local=1
>
> ifconfig ${CHDEV} 192.168.8.2/24
> ifconfig ${CHDEV}d1 192.168.9.2/24
>
> ip link add ${VRF} type vrf table 10
> ip link set dev ${VRF} up
>
> ip rule add pref 32765 table local
> ip rule del pref 0
>
> ip route add table 10 unreachable default metric 4278198272
>
> ip link set dev ${CHDEV}d1 master ${VRF}
>
> ip route add table 10 default via 192.168.9.1
> ip route add 192.168.9.0/24 via 192.168.8.1
>
>
>
>
