Hi Chris,
Could you test following patch?
DECLARE_RTL_COND(rtl_ocp_tx_cond)
{
void __iomem *ioaddr = tp->mmio_addr;
- return RTL_R8(IBISR0) & 0x02;
+ return RTL_R8(IBISR0) & 0x20;
}
static void rtl8168ep_stop_cmac(struct rtl8169_private *tp)
{
void __iomem *ioaddr = tp->mmio_addr;
RTL_W8(IBCR2, RTL_R8(IBCR2) & ~0x01);
- rtl_msleep_loop_wait_low(tp, &rtl_ocp_tx_cond, 50, 2000);
+ rtl_msleep_loop_wait_high(tp, &rtl_ocp_tx_cond, 50, 2000);
RTL_W8(IBISR0, RTL_R8(IBISR0) | 0x20);
RTL_W8(IBCR0, RTL_R8(IBCR0) & ~0x01);
}
Thanks.
------Please consider the environment before printing this e-mail.
> -----Original Message-----
> From: Chris Chiu [mailto:c...@endlessm.com]
> Sent: Monday, January 29, 2018 6:12 PM
> To: nic_swsd <nic_s...@realtek.com>; netdev@vger.kernel.org; Linux
> Kernel <linux-ker...@vger.kernel.org>; Linux Upstreaming Team
> <li...@endlessm.com>
> Subject: Re: r8169 take too long to complete driver initialization
>
> On Fri, Jan 5, 2018 at 10:17 AM, Chris Chiu <c...@endlessm.com> wrote:
> > On Wed, Dec 20, 2017 at 4:41 PM, Chris Chiu <c...@endlessm.com> wrote:
> >> Hi,
> >> We've hit a suspend/resume issue on a Acer desktop caused by
> >> r8169 driver. The dmseg
> >> https://gist.github.com/mschiu77/b741849b5070281daaead8dfee312d1a
> >> shows it's still in msleep() within a mutex lock.
> >> After looking into the code, it's caused by the
> >> rtl8168ep_stop_cmac() which is waiting 100 seconds for
> >> rtl_ocp_tx_cond. The following dmesg states that the r8169 driver is
> >> loaded.
> >>
> >> [ 20.270526] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
> >>
> >> But it takes > 100 seconds to get the following messages
> >>
> >> [ 140.400223] r8169 0000:02:00.0 (unnamed net_device)
> >> (uninitialized): rtl_ocp_tx_cond == 1 (loop: 2000, delay: 50).
> >> [ 140.413294] r8169 0000:02:00.0 eth0: RTL8168ep/8111ep at
> >> 0xffffb16c80db1000, f8:0f:41:ea:74:0d, XID 10200800 IRQ 46 [
> >> 140.413297] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200
> >> bytes, tx checksumming: ko]
> >>
> >> So any trial to suspend the machine during this period would always
> >> get device/resource busy message then abort. Is this rtl_ocp_tx_cond
> >> necessary? Because the ethernet is still working and I don't see any
> >> problem. I don't know it should be considered normal or not. Please
> >> let me know if any more information required. Thanks
> >>
> >> Chris
> >
> > gentle ping,
> >
> > cheers.
>
> Hi,
> Just found a r8168 driver which seems to be authrized by realtek for cross
> comparison. I tried applying the patch to latest 4.15 kernel and the driver
> done it's initialization in faily short time. The patch file is here
> https://gist.github.com/mschiu77/fcf406e64a1a437f46cf2be643f1057d.
>
> In mainline r8169.c, the IBISR0 register need to be polled in the
> rtl8168ep_stop_cmac().
> In the patch file, there's also the same IBISR0 polling code in
> Dash2DisableTx(), but it's been bypassed since the chipset maches
> HW_DASH_SUPPORT_TYPE_2.
> Per the rtl_chip_info[] in r8168_n.c, CFG_METHOD_23/27/28 are
> HW_DASH_SUPPORT_TYPE_2, and they happens to be the only 3 named
> RTL8168EP/8111EP in the rtl_chip_info[].
>
> To find the same matches in r8169.c, RTL_GIGA_MAC_VER_49/50/51
> seems share the same config. Can anyone clarify if the rtl_ocp_tx_cond()
> really necessary for 8168EP/8111EP?
> Or we can just ignore the condition check for RTL_GIGA_MAC_VER_49/50/51?
>
> Chris
>
> ------Please consider the environment before printing this e-mail.
