On Fri, 2017-12-29 at 02:31 +0100, Emiliano Ingrassia wrote: > Hi Martin, Hi Dave, > > On Thu, Dec 28, 2017 at 11:21:23PM +0100, Martin Blumenstingl wrote: > > Hi Dave, > > > > please do not apply this series until it got a Tested-by from Emiliano. > > > > > > Hi Emiliano, > > > > you reported [0] that you couldn't get dwmac-meson8b to work on your > > Odroid-C1. With your findings (register dumps, clk_summary output, etc.) > > I think I was able to find a fix: it consists of two patches (which you > > find in this series) > > > > Unfortunately I don't have any Meson8b boards with RGMII PHY so I could > > only partially test this (I could only check if the clocks were > > calculated correctly when using a dummy 500002394Hz input clock instead > > of MPLL2). > > > > Could you please give this series a try and let me know about the > > results? > > You obviously still need your two "ARM: dts: meson8b" patches which > > - add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi > > - enable Ethernet on the Odroid-C1 > > > > When testing on Meson8b this also needs a fix for the MPLL clock driver: > > "clk: meson: mpll: use 64-bit maths in params_from_rate", see: > > https://patchwork.kernel.org/patch/10131677/ > > > > > > I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY) > > and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working > > fine (so let's hope that this also fixes your Meson8b issue :)). > > > > > > changes since v1 at [1]: > > - changed the subject of the cover-letter to indicate that this is all > > about the RGMII clock > > - added PATCH #1 which ensures that we don't unnecessarily change the > > parent clocks in RMII mode (and also makes the code easier to > > understand) > > - changed subject of PATCH #2 (formerly PATCH #1) to state that this > > is about the RGMII clock > > - added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1) > > - replaced PATCH #3 (formerly PATCH #2) with one that sets > > CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock > > on Meson8b correctly > > > > changes since v2 at [2]: > > - added PATCH #2 to make the following patch easier > > - Emiliano reported that there's currently another bug in the > > dwmac-meson8b driver which prevents it from working with RGMII PHYs on > > Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate > > (instead of a divide by 5 or divide by 10 clock divider). This has not > > been visible on GXBB and later due to the input clock which always led > > to a selection of "divide by 10" (which is done internally in the IP > > block, but the bit actually means "enable RGMII clock output"). > > PATCH #3 was added to address this issue. > > - the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were > > updated and the patch itself rebased because the m25_div clock was > > removed with the new PATCH #3 (so some of the statements were not > > valid anymore) > > > > Here is the clk_summary relative to ethernet on Odroid-C1+ > with this new series applied: > > xtal 1 1 24000000 0 0 > sys_pll 0 0 1200000000 0 0 > cpu_clk 0 0 1200000000 0 0 > vid_pll 0 0 732000000 0 0 > fixed_pll 2 2 2550000000 0 0 > mpll2 1 1 249999701 > 0 0 > c9410000.ethernet#m250_sel 1 1 249999701 0 0 > c9410000.ethernet#m250_div 1 1 249999701 > 0 0 > c9410000.ethernet#fixed_div10 1 1 24999970 0 0 > c9410000.ethernet#m25_en 1 1 24999970 > 0 0 > > The ethernet prg0 register is set to 0x74A1 which should be correct with > respect to the information contained in the S805 SoC manual. > Actually, the ethernet is not yet fully functional. > Trying to ping the board, I can see ARP request from host to board using > tcpdump. However, the host can't see any response.
If the rx path is ok-ish, I suppose the clock setting applied is good. Maybe you could try to play with the tx delay (BIT 5-6 of the register) ? > > Following the U-Boot value for prg0 register, which is 0x7d21, I also > tried to set bit 11. As expected, this did not have any influence. > Another thing that we should check is the "Ethernet Memory PD" (see S805 > manual - sec. 5.4) register which bits 3-2 enable/disable ethernet > normal operation. However, those bits are already cleared by U-Boot. > > Thank you for the support. > > Best regards, > > Emiliano > > > > > [0] > > http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html > > [1] > > http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html > > [2] > > http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html > > > > > > Martin Blumenstingl (5): > > net: stmmac: dwmac-meson8b: only configure the clocks in RGMII mode > > net: stmmac: dwmac-meson8b: simplify generating the clock names > > net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration > > net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b > > net: stmmac: dwmac-meson8b: propagate rate changes to the parent clock > > > > .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 119 > > +++++++++++---------- > > 1 file changed, 63 insertions(+), 56 deletions(-) > > > > -- > > 2.15.1 > >
