Michael Chan wrote:
On Tue, 2006-08-08 at 01:24 +0200, Bernd Schubert wrote:
tg3.c:v3.49 (Feb 2, 2006)
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit)
10/100/1000BaseT Ethernet 00:e0:81:2b:aa:28
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
eth2: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit)
10/100/1000BaseT Ethernet 00:e0:81:2b:aa:29
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth2: dma_rwctrl[769f4000] dma_mask[64-bit]
You have ASF enabled on eth1 but not on eth2 so I wonder if ASF is
causing the problem. Can you run the same traffic on eth2 and see if
you get the same timeout problem? Thanks.
I'm also having this same problem:
divert: allocating divert_blk for bond0
tg3.c:v3.14 (November 15, 2004)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)]
(PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:2e:82:1a
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1]
TSOcap[1]
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)]
(PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:2e:82:1b
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1]
TSOcap[1]
divert: freeing divert_blk for bond0
divert: freeing divert_blk for eth0
divert: freeing divert_blk for eth1
02:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet (rev 03)
Subsystem: Broadcom Corporation: Unknown device 1644
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 161
Memory at fc8c0000 (64-bit, non-prefetchable) [size=fc8a0000]
Memory at fc8b0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at 00010000 [disabled]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/3 Enable-
02:09.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet (rev 03)
Subsystem: Broadcom Corporation: Unknown device 1644
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 169
Memory at fc8f0000 (64-bit, non-prefetchable) [size=fc8d0000]
Memory at fc8e0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at 00010000 [disabled]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/3 Enable-
I run these things with jumbo frames and bonding. In the case last
night, our machine completely locked up because both interfaces stopped
working and the channel bond between them went down. These guys are
pushing a little over 1Gb/s total traffic between them (500Mb/s each)
and one of them will take in about 300Mb/s. Outgoing packets average
20kpkts/s and incoming packets on the one interface average about
45kpkts/s (most incoming traffic is not jumbo).
This was on console:
tg3: tg3_stop_block timed out, ofs=4800 enable_bit=2
tg3: eth1: transmit timed out, resetting
tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=1800 enable_bit=2
tg3: tg3_stop_block timed out, ofs=4800 enable_bit=2
tg3: eth0: transmit timed out, resetting
tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=1800 enable_bit=2
tg3: tg3_stop_block timed out, ofs=4800 enable_bit=2
tg3: eth1: transmit timed out, resetting
tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=1800 enable_bit=2
tg3: tg3_stop_block timed out, ofs=4800 enable_bit=2
tg3: eth0: transmit timed out, resetting
tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2
tg3: tg3_stop_block timed out, ofs=1800 enable_bit=2
tg3: tg3_stop_block timed out, ofs=4800 enable_bit=2
We tried restarting networking. We tried unloading all network-related
modules and reloading them. We eventually had to reboot the box to get
networking started again. The kernel is 2.6.10, via FC2
(2.6.10-2.3.legacy). We've also had the problem with the latest FC4 kernel.
Any information would be greatly appreciated.
Philip
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
