Hi Niklas
On 11/25/2016 01:14 PM, Niklas Cassel wrote:
On 11/25/2016 01:10 PM, Niklas Cassel wrote:
On 11/24/2016 07:11 PM, Alexandre Torgue wrote:
Hi Niklas,
Hello Alexandre
On 11/24/2016 03:36 PM, Niklas Cassel wrote:
From: Niklas Cassel <niklas.cas...@axis.com>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cas...@axis.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 3 +++
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 12 +++++++++++-
2 files changed, 14 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
index 6f4f5ce25114..3e8d4fefa5e0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
@@ -155,8 +155,11 @@ enum power_event {
#define MTL_CHAN_RX_DEBUG(x) (MTL_CHANX_BASE_ADDR(x) + 0x38)
#define MTL_OP_MODE_RSF BIT(5)
+#define MTL_OP_MODE_TXQEN BIT(3)
#define MTL_OP_MODE_TSF BIT(1)
+#define MTL_OP_MODE_TQS_MASK GENMASK(24, 16)
+
#define MTL_OP_MODE_TTC_MASK 0x70
#define MTL_OP_MODE_TTC_SHIFT 4
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
index 116151cd6a95..577316de6ba8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
@@ -213,7 +213,17 @@ static void dwmac4_dma_chan_op_mode(void __iomem *ioaddr,
int txmode,
else
mtl_tx_op |= MTL_OP_MODE_TTC_512;
}
-
+ /* For an IP with DWC_EQOS_NUM_TXQ == 1, the fields TXQEN and TQS are RO
+ * with reset values: TXQEN on, TQS == DWC_EQOS_TXFIFO_SIZE.
+ * For an IP with DWC_EQOS_NUM_TXQ > 1, the fields TXQEN and TQS are R/W
+ * with reset values: TXQEN off, TQS 256 bytes.
+ *
+ * Write the bits in both cases, since it will have no effect when RO.
+ * For DWC_EQOS_NUM_TXQ > 1, the top bits in MTL_OP_MODE_TQS_MASK might
+ * be RO, however, writing the whole TQS field will result in a value
+ * equal to DWC_EQOS_TXFIFO_SIZE, just like for DWC_EQOS_NUM_TXQ == 1.
+ */
+ mtl_tx_op |= MTL_OP_MODE_TXQEN | MTL_OP_MODE_TQS_MASK;
Your patch sounds good. Just one question:
In synopsys databook I use, I see that MTL_OP_MODE_TXQEN for channel 2 can take several
values "disabled / enabled / Enabled in AV mode":
Transmit Queue Enable
This field is used to enable/disable the transmit queue 1. 00 R/W
■ 2'b00 - Not enabled
■ 2'b01 - Enable in AV mode (Reserved when Enable Audio Video
Bridging is not selected while configuring the core)
■ 2'b10 - Enabled
■ 2'b11 - Reserved
Do you plan to manage av mode in a future patch ?
We are not planning on using the AV mode.
We will probably not use TXQ1 at all.
I noticed that the MAC_HW_Feature2 Register actually has a TXQCNT field.
It is currently saved in priv->dma_cap.number_tx_channel.
If you prefer, I could do a patch V2 where we only set the bits if
priv->dma_cap.number_tx_channel > 1
Oh, sorry, that was number of tx _channels_,
not number of tx _queues_.
However, we could add a number_tx_queue to struct dma_features,
if you would prefer that.
I agree your patch is good. It will work even if we use several tx
channels. We will see in the future for AV mode.
regards
alex
However, I don't think the current patch is too bad either, since the bits
are RO when number_tx_channel == 1.
Regards
Alex
writel(mtl_tx_op, ioaddr + MTL_CHAN_TX_OP_MODE(channel));
mtl_rx_op = readl(ioaddr + MTL_CHAN_RX_OP_MODE(channel));
