We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.za...@pengutronix.de>
---
Changes since v1:
- Rename device tree property from "fxen" to "micrel,fiber-mode".
- Move device tree documentation into micrel.txt, this property could be
useful for other PHYs, too.
---
Documentation/devicetree/bindings/net/micrel.txt | 10 +++++++
drivers/net/phy/micrel.c | 34 ++++++++++++++++++++++--
include/linux/micrel_phy.h | 1 +
3 files changed, 43 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/micrel.txt
b/Documentation/devicetree/bindings/net/micrel.txt
index 87496a8..8d157f0 100644
--- a/Documentation/devicetree/bindings/net/micrel.txt
+++ b/Documentation/devicetree/bindings/net/micrel.txt
@@ -35,3 +35,13 @@ Optional properties:
supported clocks:
- KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference
input clock. Used to determine the XI input clock.
+
+ - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
+
+ Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
+ by the FXEN boot strapping pin. It can't be determined from the PHY
+ registers whether the PHY is in fiber mode, so this boolean device tree
+ property can be used to describe it.
+
+ In fiber mode, auto-negotiation is disabled and the PHY can only work in
+ 100base-fx (full and half duplex) modes.
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 5a8fefc..059f13b 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -311,6 +311,36 @@ static int kszphy_config_init(struct phy_device *phydev)
return 0;
}
+static int ksz8041_config_init(struct phy_device *phydev)
+{
+ struct device_node *of_node = phydev->mdio.dev.of_node;
+
+ /* Limit supported and advertised modes in fiber mode */
+ if (of_property_read_bool(of_node, "micrel,fiber-mode")) {
+ phydev->dev_flags |= MICREL_PHY_FXEN;
+ phydev->supported &= SUPPORTED_FIBRE |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_100baseT_Half;
+ phydev->advertising &= ADVERTISED_FIBRE |
+ ADVERTISED_100baseT_Full |
+ ADVERTISED_100baseT_Half;
+ phydev->autoneg = AUTONEG_DISABLE;
+ }
+
+ return kszphy_config_init(phydev);
+}
+
+static int ksz8041_config_aneg(struct phy_device *phydev)
+{
+ /* Skip auto-negotiation in fiber mode */
+ if (phydev->dev_flags & MICREL_PHY_FXEN) {
+ phydev->speed = SPEED_100;
+ return 0;
+ }
+
+ return genphy_config_aneg(phydev);
+}
+
static int ksz9021_load_values_from_of(struct phy_device *phydev,
const struct device_node *of_node,
u16 reg,
@@ -788,8 +818,8 @@ static struct phy_driver ksphy_driver[] = {
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.driver_data = &ksz8041_type,
.probe = kszphy_probe,
- .config_init = kszphy_config_init,
- .config_aneg = genphy_config_aneg,
+ .config_init = ksz8041_config_init,
+ .config_aneg = ksz8041_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
diff --git a/include/linux/micrel_phy.h b/include/linux/micrel_phy.h
index 2e5b194..257173e 100644
--- a/include/linux/micrel_phy.h
+++ b/include/linux/micrel_phy.h
@@ -37,6 +37,7 @@
/* struct phy_device dev_flags definitions */
#define MICREL_PHY_50MHZ_CLK 0x00000001
+#define MICREL_PHY_FXEN 0x00000002
#define MICREL_KSZ9021_EXTREG_CTRL 0xB
#define MICREL_KSZ9021_EXTREG_DATA_WRITE 0xC
--
2.8.1
