Hi,
I am trying to integrate the rtl8168 PCIe card to have Ethernet functional on my
Keystone EVM. I purchased the rtl8111c Gib card from Amazon. The Card is
detected
by the RC and I can see it is enumerated and show up when doing lspci command.
However I can't get the Ethernet port functional. Does this need MSI interrupt?
I can't see it has requested any.
root@k2g-evm:~# cat /proc/interrupts
CPU0
18: 152104 GIC 27 Edge arch_timer
22: 3326 GIC 196 Edge serial
24: 0 GIC 120 Edge 2530000.i2c
25: 0 GIC 121 Edge 2530400.i2c
26: 14 GIC 98 Edge 21805800.spi
27: 0 GIC 160 Edge 2680000.keystone-dwc3, xhci-hcd:usb1
30: 0 GIC 228 Edge gpmc
31: 0 GIC 229 Edge 21c8000.elm
32: 159 GIC 356 Level 2a00000.msgmgr rx_005_002
49: 0 GIC 232 Edge 2700000.edma_ccint
51: 0 GIC 249 Edge 2700000.edma_ccerrint
52: 1840 GIC 240 Edge 2728000.edma_ccint
54: 2 GIC 252 Edge 2728000.edma_ccerrint
57: 5424 GIC 128 Edge mmc0
58: 461 GIC 129 Edge mmc1
285: 0 Keystone-PCIe-MSI-IRQ 0 Edge PCIe PME, aerdrv
IPI0: 0 CPU wakeup interrupts
IPI1: 0 Timer broadcast interrupts
IPI2: 0 Rescheduling interrupts
IPI3: 0 Function call interrupts
IPI4: 0 Single function call interrupts
IPI5: 0 CPU stop interrupts
IPI6: 0 IRQ work interrupts
IPI7: 0 completion interrupts
root@k2g-evm:~# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
gre0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-50-00-00-00-00-00-00-00-00
NOARP MTU:1476 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
gretap0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1462 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:968 (968.0 B) TX bytes:968 (968.0 B)
tunl0 Link encap:UNSPEC HWaddr
00-00-00-00-31-00-00-50-00-00-00-00-00-00-00-00
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@k2g-evm:~# ifup eth0
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
[ 2.303965] PCI host bridge /soc/pcie@21800000 ranges:
[ 2.309108] No bus range found for /soc/pcie@21800000, using [bus 00-ff]
[ 2.316269] IO 0x23250000..0x23253fff -> 0x00000000
[ 2.321499] MEM 0x50000000..0x5fffffff -> 0x50000000
[ 2.331666] keystone-pcie 21801000.pcie: PCI host bridge to bus 0000:00
[ 2.338283] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.343937] pci_bus 0000:00: root bus resource [io 0x0000-0x3fff]
[ 2.350114] pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff]
[ 2.357095] pci 0000:00:00.0: [104c:b00b] type 01 class 0x060400
[ 2.357665] PCI: bus0: Fast back to back transfers disabled
[ 2.363717] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
[ 2.363809] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 2.363867] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[ 2.363909] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x0000ffff 64bit
pref]
[ 2.363939] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 2.364099] pci 0000:01:00.0: supports D1 D2
[ 2.364116] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.381251] PCI: bus1: Fast back to back transfers disabled
[ 2.386989] pci 0000:00:00.0: BAR 8: assigned [mem 0x50000000-0x500fffff]
[ 2.393937] pci 0000:00:00.0: BAR 9: assigned [mem 0x50100000-0x501fffff
pref]
[ 2.401221] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 2.407320] pci 0000:01:00.0: BAR 6: assigned [mem 0x50100000-0x5011ffff
pref]
[ 2.414597] pci 0000:01:00.0: BAR 4: assigned [mem 0x50120000-0x5012ffff
64bit pref]
[ 2.422380] pci 0000:01:00.0: BAR 2: assigned [mem 0x50000000-0x50000fff
64bit]
[ 2.429702] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 2.435821] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.440783] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff]
[ 2.446896] pci 0000:00:00.0: bridge window [mem 0x50000000-0x500fffff]
[ 2.453699] pci 0000:00:00.0: bridge window [mem 0x50100000-0x501fffff
pref]
[ 2.461453] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 2.468411] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 2.475075] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
[ 2.475392] aer 0000:00:00.0:pcie02: service driver aer loaded
[ 2.475652] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.481419] r8169 0000:01:00.0: enabling device (0140 -> 0143)
[ 2.488865] r8169 0000:01:00.0 eth0: RTL8169 at 0xf0d6a000,
00:00:00:00:00:00, XID 00000000 IRQ 286
[ 2.498259] r8169 0000:01:00.0 eth0: jumbo features [frames: 7152 bytes, tx
checksumming: ok]
Complete log at http://pastebin.ubuntu.com/16268925/
Can someone help me figure out what is missing?
--
Murali Karicheri
Linux Kernel, Keystone
