Hello I am running OpenBSD-current.
My ppp.conf: # A PPPoE (PPP over Ethernet) setup may look like this: # pppoe: set device "!/usr/sbin/pppoe -i em1" set mtu max 1492 set mru max 1492 set dial set login set authname seednet set authkey seednet enable dns add! default HISADDR set speed sync disable acfcomp protocomp deny acfcomp using ppp -ddial pppoe works just fine. When using kernel mode hostname.pppoe1: inet 0.0.0.0 255.255.255.255 NONE pppoedev em1 authproto chap authname 'seednet' authkey 'seednet' up debug dest 0.0.0.1 !/sbin/route add default -ifp pppoe1 0.0.0.1 and the dmesg log is that because of the timeout? Thanks. pppoe1 (8863) state=2, session=0x0 output -> 00:30:88:01:42:7d, len=18 pppoe1: timeout pppoe1 (8863) state=2, session=0x0 output -> 00:30:88:01:42:7d, len=18 pppoe1: session 0x220f connected pppoe1: lcp up(starting) pppoe1: lcp starting->req-sent pppoe1: lcp output <conf-req id=0x1 len=10 05-06-e4-57-93-3a> pppoe1 (8864) state=3, session=0x220f output -> 00:30:88:01:42:7d, len=18 pppoe1: lcp input(req-sent): <conf-req id=0x7a len=18 01-04-05-d4-03-04-c0-23-05-06-4f-34-72-ef-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp parse opts: mru auth-proto magic pppoe1: lcp parse opt values: mru 1492 auth-proto [mine 0x0 != his pap] magic 0x4f3472ef send conf-nak pppoe1: lcp output <conf-nak id=0x7a len=8 03-04-c2-23> pppoe1 (8864) state=3, session=0x220f output -> 00:30:88:01:42:7d, len=16 pppoe1: lcp input(req-sent): <conf-ack id=0x1 len=10 05-06-e4-57-93-3a-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp req-sent->ack-rcvd pppoe1: lcp input(ack-rcvd): <conf-req id=0x7b len=14 01-04-05-d4-05-06-4f-34-72-ef-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp parse opts: mru magic pppoe1: lcp parse opt values: mru 1492 magic 0x4f3472ef send conf-ack pppoe1: lcp output <conf-ack id=0x7b len=14 01-04-05-d4-05-06-4f-34-72-ef> pppoe1 (8864) state=3, session=0x220f output -> 00:30:88:01:42:7d, len=22 pppoe1: lcp ack-rcvd->opened pppoe1: lcp tlu pppoe1: phase authenticate pppoe1: lcp input(opened): <term-req id=0x7c len=4 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp opened->stopping pppoe1: phase terminate pppoe1: lcp send terminate-ack pppoe1: lcp output <term-ack id=0x7c len=4> pppoe1 (8864) state=3, session=0x220f output -> 00:30:88:01:42:7d, len=12 pppoe1: lcp TO(stopping) rst_counter = 0 pppoe1: lcp stopping->stopped pppoe1: phase dead pppoe1: timeout pppoe1: disconnecting pppoe1: lcp down(stopped) pppoe1: lcp stopped->starting pppoe1: phase establish pppoe1 (8863) state=1, session=0x0 output -> ff:ff:ff:ff:ff:ff, len=18 pppoe1: Down event (carrier loss), taking interface down.<7>pppoe1: lcp close(starting) pppoe1: lcp starting->initial pppoe1: phase dead pppoe1 (8863) state=2, session=0x0 output -> 00:30:88:01:42:7d, len=18 pppoe1: session 0x1d0d connected pppoe1: lcp open(initial) pppoe1: lcp initial->starting pppoe1: phase establish pppoe1: lcp up(starting) pppoe1: lcp starting->req-sent pppoe1: lcp output <conf-req id=0x2 len=10 05-06-6a-fa-13-f3> pppoe1 (8864) state=3, session=0x1d0d output -> 00:30:88:01:42:7d, len=18 pppoe1: lcp input(req-sent): <conf-req id=0xc0 len=18 01-04-05-d4-03-04-c0-23-05-06-26-6c-3c-34-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp parse opts: mru auth-proto magic pppoe1: lcp parse opt values: mru 1492 auth-proto [mine 0x0 != his pap] magic 0x266c3c34 send conf-nak pppoe1: lcp output <conf-nak id=0xc0 len=8 03-04-c2-23> pppoe1 (8864) state=3, session=0x1d0d output -> 00:30:88:01:42:7d, len=16 pppoe1: lcp input(req-sent): <conf-ack id=0x2 len=10 05-06-6a-fa-13-f3-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp req-sent->ack-rcvd pppoe1: lcp input(ack-rcvd): <conf-req id=0xc1 len=14 01-04-05-d4-05-06-26-6c-3c-34-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp parse opts: mru magic pppoe1: lcp parse opt values: mru 1492 magic 0x266c3c34 send conf-ack pppoe1: lcp output <conf-ack id=0xc1 len=14 01-04-05-d4-05-06-26-6c-3c-34> pppoe1 (8864) state=3, session=0x1d0d output -> 00:30:88:01:42:7d, len=22 pppoe1: lcp ack-rcvd->opened pppoe1: lcp tlu pppoe1: up pppoe1: phase authenticate pppoe1: lcp input(opened): <term-req id=0xc2 len=4 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00-00-00-00-00-00-00-00> pppoe1: lcp opened->stopping pppoe1: phase terminate pppoe1: lcp send terminate-ack pppoe1: lcp output <term-ack id=0xc2 len=4> pppoe1 (8864) state=3, session=0x1d0d output -> 00:30:88:01:42:7d, len=12
