On 1/12/2008, at 9:24 AM, Chris wrote:
2) in an earlier message you indicated that there was some kind of
RAID on this system, I think it is safe to say that it is a BIOS-
assisted
software RAID, which COULD be causing you problems if it is still
configured in the BIOS. And even if it isn't causing this problem,
it WILL bite you in the future when the BIOS decides top copy
something
from one drive to the other...
Sorry about my previous post but there is no RAID.
So, start by disabling the BIOS "RAID" do-hickey thing and unplug
the second drive. I suspect you will have no problems then.
I have tried pulling the plug on the second disk (wd1) with no luck.
Once you convince yourself the size of the drive is not directly
an issue, I'd suggest starting over with a more sane partitioning
plan. Just because you have a cheap 500G disk doesn't mean you
need to allocate all or most of it. For one, the bigger the disk,
the longer it takes to fsck after you trip over the power cord.
I actually have two "cheap" 500GB; so that makes it 1 terabyte. I
don't mind fsck doing its thing when I trip over the cable. But I
really do need a large /data1 partition to rsync stuff over from other
places. Here's the last disk partition I tried (and it didn't work): /
10g, swap 3g, /tmp 20g, /home 100g, /var/ 50g, /usr/ 50g. It was
sitting there for 30 minutes after the last file set was installed
(xserv44.tgz) and then I turned it off.
Thanks for any further help.
I've got a couple of Dell SC440s with the same sort of set-up, and
no problems here.
Two 500Gb drives, wd0 and wd1:
# df -h
Filesystem Size Used Avail Capacity Mounted on
/dev/wd0a 84.4M 36.6M 43.6M 46% /
/dev/wd0h 1008M 2.7M 955M 0% /home
/dev/wd0i 436G 121G 294G 29% /public
/dev/wd1a 458G 116G 320G 27% /public2
/dev/wd0d 1008M 2.0K 958M 0% /tmp
/dev/wd0g 9.8G 1.9G 7.4G 21% /usr
/dev/wd0e 9.8G 31.2M 9.3G 0% /var
I wanted one large dumping ground on wd0, and another on wd1,
and had no trouble creating them (I cannot recall any lengthy delay;
not the same as saying there wasn't one, but I don't remember it.)
And yes, fsck does take a long time.
Thanks.
dmesg (sd0 is an 8Gb USB memstick):
OpenBSD 4.4 (GENERIC) #0: Tue Nov 11 10:18:14 NZDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) D CPU 3.00GHz ("GenuineIntel" 686-class) 3 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-
CPL,EST,CNXT-ID,CX16,xTPR
real mem = 1071722496 (1022MB)
avail mem = 1027870720 (980MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 07/03/07, BIOS32 rev. 0 @
0xffe90, SMBIOS rev. 2.3 @ 0xf0450 (63 entries)
bios0: vendor Dell Inc. version "1.4.1" date 07/03/2007
bios0: Dell Inc. PowerEdge SC440
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfed10/256 (14 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GH LPC" rev
0x00)
pcibios0: PCI bus #5 is the last bus
bios0: ROM list: 0xc0000/0x9000 0xc9000/0x2000! 0xcb000/0x1000
cpu0 at mainbus0
cpu0: Enhanced SpeedStep disabled by BIOS
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel E7230 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel E7230 PCIE" rev 0x00: irq 11
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: irq 11
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 4 "Intel 82801G PCIE" rev 0x01: irq 11
pci3 at ppb2 bus 3
em0 at pci3 dev 0 function 0 "Intel PRO/1000 PT (82572EI)" rev 0x06:
irq 11, address 00:15:17:3d:38:11
ppb3 at pci0 dev 28 function 5 "Intel 82801G PCIE" rev 0x01: irq 10
pci4 at ppb3 bus 4
bge0 at pci4 dev 0 function 0 "Broadcom BCM5754" rev 0x02,
BCM5754/5787 A2 (0xb002): irq 10, address 00:1d:09:09:94:17
brgphy0 at bge0 phy 1: BCM5787 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: irq 9
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: irq 5
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: irq 3
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: irq 10
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: irq 9
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci5 at ppb4 bus 5
vga1 at pci5 dev 7 function 0 "ATI ES1000" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM
disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CDRWDVD TS-H492C, DE02>
ATAPI 5/cdrom removable
atapiscsi1 at pciide0 channel 0 drive 1
scsibus1 at atapiscsi1: 2 targets, initiator 7
st0 at scsibus1 targ 0 lun 0: <Seagate, STT3401A, 310C> ATAPI 1/
sequential removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
st0(pciide0:0:1): using PIO mode 3
pciide0: channel 1 ignored (disabled)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using irq 5 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3500630NS>
wd0: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
wd1 at pciide1 channel 0 drive 1: <ST3500630NS>
wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 5
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: irq 10
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM ECC PC2-5300CL5
spdmem1 at iic0 addr 0x52: 512MB DDR2 SDRAM ECC PC2-5300CL5
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
biomask f7ed netmask ffed ttymask ffff
mtrr: Pentium Pro MTRR support
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Composite USB
PS2 Converter USB to PS2 Adaptor V3.10" rev 1.10/3.10 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 1 "Composite USB
PS2 Converter USB to PS2 Adaptor V3.10" rev 1.10/3.10 addr 2
uhidev1: iclass 3/1, 3 report ids
ums0 at uhidev1 reportid 1: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
umass0 at uhub0 port 4 configuration 1 interface 0 " USB Flash
Memory" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd0 at scsibus2 targ 1 lun 0: <, USB Flash Memory, PMAP> SCSI0 0/
direct removable
sd0: 7751MB, 988 cyl, 255 head, 63 sec, 512 bytes/sec, 15874048 sec
total
