I have got the same issue with a;
HP Pavillon Intel(r) Celeron processor 400MHz
192MB SDRAM memory
40G hardrive from IBM ITACHI
CDROM 32x max. speed
I therefore didn't try any installation from install43.iso neither a kernel
rebuild as you.
But the install44.iso force me to install it by swaping the HDD into a
ThinkCenter 1.2 MHz and reswaping it to the HP pf box.
/////////////////
/// dmesg ///
////////////////
OpenBSD 4.4 (GENERIC) #0: Sun Nov 16 13:13:27 MST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Celeron ("GenuineIntel" 686-class, 128KB L2 cache) 401 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 200830976 (191MB)
avail mem = 185638912 (177MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 06/25/99, BIOS32 rev. 0 @ 0xfd7c0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xfd7c0/0x840
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf60/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 9
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa800 0xdc000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage Pro" rev 0x5c
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
agp0 at vga1: aperture at 0xf8000000, size 0x4000000
drm at vga1 unsupported
piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DJNA-371350>
wd0: 16-sector PIO, LBA, 12949MB, 26520480 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
wdc_atapi_start: not ready, st = 58
atapiscsi0(pciide0:1:0): using PIO mode 0
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 10
piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x02: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 64MB SDRAM non-parity PC100CL3
spdmem1 at iic0 addr 0x51: 128MB SDRAM non-parity PC100CL2
vr0 at pci0 dev 10 function 0 "VIA RhineII-2" rev 0x43: irq 5, address
XX:XX:XX:XX:XX:XX
sqphy0 at vr0 phy 8: Seeq 80225 10/100 PHY, rev. 0
ne3 at pci0 dev 11 function 0 "Realtek 8029" rev 0x00: irq 3, address
XX:XX:XX:XX:XX:XX
isa0 at piixpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask ff45 netmask ff6d ttymask ffff
mtrr: Pentium Pro MTRR support
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
syncing disks... done
rebooting...
***************************************
Cheer.
--
View this message in context:
http://www.nabble.com/4.4-installer-can%27t-see-CD-drive-tp20336540p20644117.html
Sent from the openbsd user - misc mailing list archive at Nabble.com.
