On Thursday 06 November 2008 22.24.49 Ted Unangst wrote:
> On Thu, Nov 6, 2008 at 11:49 AM, Jamie Cuesta <[EMAIL PROTECTED]>
wrote:
> > I was hoping to include a dmesg via serial port capture (my box
> > does not include a floppy), but
>
> Use ftp.
On Friday 07 November 2008 17.24.52 Ted Unangst wrote:
> Ok, you are having serious interrupt issues. The only thing I can
> think of to try is disabling acpi (via boot -c), but that's a long
> shot.
I have the same board, and can confirm that without disabling
acpi, -current OpenBSD can not recognize the network device, the hard
drive nor the attached usb devices (disk, keyboard etc...).
However, after disabling acpi, -current fires up, and recognizes the
hard drives and the network card. That's how I could manage to get a
dmesg. So here it is, and also sent to dmesg@:
OpenBSD 4.4-current (RAMDISK_CD) #964: Fri Nov 7 03:25:28 MST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Celeron(R) CPU 220 @ 1.20GHz ("GenuineIntel" 686-class)
1.21 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
real mem = 1033404416 (985MB)
avail mem = 992567296 (946MB)
User Kernel Config
UKC> disable acpi
241 acpi0 disabled
UKC> quit
Continuing...
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/04/08, SMBIOS rev. 2.4 @
0xe4da0 (23 entries)
bios0: vendor Intel Corp. version "LY66210M.86A.0137.2008.0104.1540"
date 01/04/2008
bios0: Intel Corporation D201GLY
acpi at bios0 function 0x0 not configured
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc0000/0x10000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "SiS 662 PCI" rev 0x01
ppb0 at pci0 dev 1 function 0 "SiS 648FX AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x04
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "SiS 964 ISA" rev 0x36
pciide0 at pci0 dev 2 function 5 "SiS 5513 EIDE" rev 0x01: 964: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4120B, A111> ATAPI
5/cdrom removable
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
"SiS 7012 AC97" rev 0xa0 at pci0 dev 2 function 7 not configured
ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: irq 11,
version 1.0, legacy support
ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: irq 10,
version 1.0, legacy support
ohci2 at pci0 dev 3 function 2 "SiS 5597/5598 USB" rev 0x0f: irq 11,
version 1.0, legacy support
ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: irq 10
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "SiS EHCI root hub" rev 2.00/1.00 addr 1
sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91: irq 11,
address 00:1c:c0:41:23:6b
ukphy0 at sis0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI
0x0050ef, model 0x0007
pciide1 at pci0 dev 5 function 0 "SiS 181 SATA" rev 0x01: DMA
pciide1: using irq 10 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <FUJITSU MHW2060BH>
wd0: 16-sector PIO, LBA48, 57226MB, 117199616 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
rl0 at pci0 dev 6 function 0 "Realtek 8139" rev 0x10: irq 10, address
00:30:4f:19:3e:fd
rlphy0 at rl0 phy 0: RTL internal PHY
ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "SiS OHCI root hub" rev 1.00/1.00 addr 1
biomask fffd netmask fffd ttymask ffff
rd0: fixed, 3800 blocks
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Logitech Logitech
USB Keyboard" rev 1.10/15.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 1 "Logitech Logitech
USB Keyboard" rev 1.10/15.00 addr 2
uhidev1: iclass 3/0, 3 report ids
uhid at uhidev1 reportid 1 not configured
uhid at uhidev1 reportid 2 not configured
uhid at uhidev1 reportid 3 not configured
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
Daniel
--
LEVAI Daniel
PGP key ID = 0x4AC0A4B1
Key fingerprint = D037 03B9 C12D D338 4412 2D83 1373 917A 4AC0 A4B1
