This build seems to go into an endless reboot cycle, rebooting before
anything shows up in the console of a Soekris net4801. The previous
snapshot (build #1004) works fine. Unfortunately I have nothing to show
for it as far as filing a proper bug report. BIOS screen followed by
the changing console to com0 message followed by the BIOS screen etc.
Problem build:
OpenBSD 4.4-beta (GENERIC) #1010: Sat Aug 2 12:39:46 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
Last working version dmesg:
OpenBSD 4.4-beta (GENERIC) #1004: Thu Jul 31 00:42:16 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133787648 (127MB)
avail mem = 120946688 (115MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/80/03, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c2:9e:30
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c2:9e:31
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c2:9e:32
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX-2048>
wd0: 4-sector PIO, LBA, 1953MB, 4001760 sectors
wd0(pciide0:0:0): using PIO mode 4
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6 revision 3
wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, version
1.0, legacy support
isa0 at gscpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask fbe5 netmask ffe5 ttymask ffff
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
