Hi all,
I have configured a carp(4) over vlan(4) over trunk(4) (failover
mode) over bge(4) setup. While everything seems to work fine,
the kernel on the machine where carp is in the master state
keeps spitting out warnings as follows:
arpresolve: XX.YY.16.3: route without link local address
Note: XX.YY.16.3 is the IP of the carp interface. There are some
other vlans defined on the trunk, but no other carp interface.
The machine acts as a router (BGPD is running as well).
The machine is running OpenBSD 4.3-current as of may 2nd.
Has anybody seen this before?
Thanks,
Christian
# cat /etc/hostname.carp1
XX.YY.16.3 netmask 255.255.255.224 carpdev vlan100 vhid 1
# cat /etc/hostname.vlan100
XX.YY.16.1 netmask 255.255.255.224 vlan 100 vlandev trunk0
# route -n get XX.YY.16.1
route to: XX.YY.16.1
destination: XX.YY.16.1
interface: lo0
if address: XX.YY.16.1
flags: <UP,HOST,DONE,LLINFO,CLONED>
use hopcount mtu expire
450 0 0 0
# route -n get XX.YY.16.3
route to: XX.YY.16.3
destination: XX.YY.16.3
interface: carp1
if address: XX.YY.16.3
flags: <UP,HOST,DONE>
use hopcount mtu expire
4 0 0 0
# cat /var/run/dmesg.boot
OpenBSD 4.3-current (GENERIC.MP) #0: Sat May 3 00:08:05 CEST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel"
686-class) 2.21 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
real mem = 1071947776 (1022MB)
avail mem = 1028378624 (980MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 03/05/08, BIOS32 rev. 0 @
0xfac90, SMBIOS rev. 2.5 @ 0x3ff9c000 (46 entries)
bios0: vendor Dell Inc. version "1.2.1" date 03/05/2008
bios0: Dell Inc. PowerEdge R200
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP APIC SPCR HPET MCFG WD__ SLIC ERST HEST
BERT EINJ SSDT SSDT SSDT
acpi0: wakeup devices PCI0(S5)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 200MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel"
686-class) 2.21 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
ioapic1 at mainbus0: apid 3 pa 0xfec10000, version 20, 24 pins
ioapic1: misconfigured as apic 0, remapped to apid 3
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (PEX1)
acpiprt2 at acpi0: bus 2 (SBE0)
acpiprt3 at acpi0: bus 3 (PXHA)
acpiprt4 at acpi0: bus 5 (SBE4)
acpiprt5 at acpi0: bus 6 (SBE5)
acpiprt6 at acpi0: bus 7 (COMP)
acpicpu0 at acpi0: FVS, 2200, 2000, 1800, 1600, 1400, 1200 MHz
acpicpu1 at acpi0: FVS, 2200, 2000, 1800, 1600, 1400, 1200 MHz
bios0: ROM list: 0xc0000/0xb000 0xcb000/0x3c00 0xcf000/0x600
0xec000/0x4000!
ipmi at mainbus0 not configured
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 3200/3210 Host" rev 0x01
ppb0 at pci0 dev 1 function 0 "Intel 3200/3210 PCIE" rev 0x01:
apic 2 int 16 (irq 15)
pci1 at ppb0 bus 1
em0 at pci1 dev 0 function 0 "Intel PRO/1000 PT (82571EB)" rev
0x06: apic 2 int 16 (irq 15), address 00:15:17:5c:14:b4
em1 at pci1 dev 0 function 1 "Intel PRO/1000 PT (82571EB)" rev
0x06: apic 2 int 17 (irq 14), address 00:15:17:5c:14:b5
ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02
pci2 at ppb1 bus 2
ppb2 at pci2 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
pci3 at ppb2 bus 3
ppb3 at pci3 dev 2 function 0 "Hint HB4 PCI-PCI" rev 0x04
pci4 at ppb3 bus 4
vga1 at pci4 dev 2 function 0 "ATI Radeon VE QY" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
vendor "Dell", unknown product 0x0010 (class undefined unknown
subclass 0x00, rev 0x00) at pci4 dev 4 function 0 not configured
"Dell DRAC 4 Virtual UART" rev 0x00 at pci4 dev 4 function 1 not
configured
"Dell DRAC 4 SMIC" rev 0x00 at pci4 dev 4 function 2 not configured
pciide0 at pci4 dev 7 function 0 "CMD Technology PCI0680" rev 0x02
pciide0: bus-master DMA support present
pciide0: channel 0 wired to native-PCI mode
pciide0: using apic 3 int 0 (irq 15) for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
sd0 at scsibus0 targ 0 lun 0: <DELL, VSF, 0123> SCSI0 0/direct
removable
sd0: drive offline
atapiscsi1 at pciide0 channel 0 drive 1
scsibus1 at atapiscsi1: 2 targets
cd0 at scsibus1 targ 0 lun 0: <DELL, VCD, 0133> SCSI0 5/cdrom
removable
sd0(pciide0:0:0): using PIO mode 3
cd0(pciide0:0:1): using PIO mode 3
pciide0: channel 1 wired to native-PCI mode
ppb4 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02
pci5 at ppb4 bus 5
bge0 at pci5 dev 0 function 0 "Broadcom BCM5721" rev 0x21,
BCM5750 C1 (0x4201): apic 2 int 16 (irq 15), address
00:19:b9:fa:4f:99
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
ppb5 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02
pci6 at ppb5 bus 6
bge1 at pci6 dev 0 function 0 "Broadcom BCM5721" rev 0x21,
BCM5750 C1 (0x4201): apic 2 int 17 (irq 14), address
00:19:b9:fa:4f:9a
brgphy1 at bge1 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02:
apic 2 int 21 (irq 11)
uhci1 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02:
apic 2 int 20 (irq 10)
uhci2 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02:
apic 2 int 21 (irq 11)
ehci0 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02:
apic 2 int 21 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb6 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
pci7 at ppb6 bus 7
ichpcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02:
PM disabled
pciide1 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02:
DMA, channel 0 configured to native-PCI, channel 1 configured to
native-PCI
pciide1: using apic 2 int 23 (irq 6) for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <SAMSUNG HE160HJ>
wd0: 16-sector PIO, LBA48, 152587MB, 312500000 sectors
atapiscsi2 at pciide1 channel 0 drive 1
scsibus2 at atapiscsi2: 2 targets
cd1 at scsibus2 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR-T10N, 1.02>
SCSI0 5/cdrom removable
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
cd1(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 2
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
mtrr: Pentium Pro MTRR support
uhub4 at uhub0 port 5 "Cypress Semiconductor USB2 Hub" rev
2.00/0.0b addr 2
uhidev0 at uhub1 port 1 configuration 1 interface 0 "Dell DRAC4"
rev 1.10/0.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1 "Dell DRAC4"
rev 1.10/0.00 addr 2
uhidev1: iclass 3/1
ums0 at uhidev1
ums0: X report 0x0002 not supported
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
