To be honest I am surprised they were that fast. Solid state isn't up to par yet so these numbers are actually quite good. The next generation is going to be much more competitive.
On Mon, Jun 16, 2008 at 09:44:16AM -0400, Brandon Mercer wrote: > Yes, just a little bit... The do seem slow, but I acknowledge the fact > that the system bus could be choking a bit. The numbers that have > been produced in other benchmarks are right around 100/80 read/write. > I'm not entirely sure that the system board that I have is the > greatest to achieve this on. The first time I ran bonnie++ on the 4.2 > snapshot I had close to 16k interrupts. Ran out of time trying to > pinpoint the bottleneck. > > On Mon, Jun 16, 2008 at 9:37 AM, Marco Peereboom <[EMAIL PROTECTED]> wrote: > > I am honestly curious, are you surprised by these results? > > > > On Sun, Jun 15, 2008 at 08:09:48PM -0400, Brandon Mercer wrote: > >> Hello all. > >> Well my raid 10 of 10k scsis just wasn't cutting it anymore so I > >> decided to replace it with something interesting. I picked up an > >> Mtron mobi 3000 solid state hard drive. This drive didn't come > >> without issue. I poorly researched hardware and then had to > >> substitute my mainboard choice when the local store was out of stock. > >> Long story short the drive wound up on "cheap" board connecting to > >> pciide. (One note: I had to upgrade from 4.2 snapshot to 4.3 -current > >> in order to get any kind of performance from pciide) First thing I > >> did, bonnie++ of course! > >> > >> Version 1.03 ------Sequential Output------ --Sequential Input- > >> --Random- > >> -Per Chr- --Block-- -Rewrite- -Per Chr- --Block-- > >> --Seeks-- > >> Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP > >> /sec %CP > >> db1.eutonian.com 4G 61968 88 54228 52 33751 11 45898 75 87135 18 > >> 2076 11 > >> ------Sequential Create------ --------Random > >> Create-------- > >> -Create-- --Read--- -Delete-- -Create-- --Read--- > >> -Delete-- > >> files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP > >> /sec %CP > >> 16 +++++ +++ +++++ +++ 29239 73 32630 63 +++++ +++ > >> +++++ +++ > >> db1.eutonian.com,4G,61968,88,54228,52,33751,11,45898,75,87135,18,2075.7,11,16,+++++,+++,+++++,+++,29239,73,32630,63,+++++,+++,+++++,+++ > >> > >> During this test pciide hung out around 3800-4200 interrupts. Dmesg > >> follows. > >> > >> OpenBSD 4.3-current (GENERIC.MP) #1728: Sat Jun 14 20:01:03 MDT 2008 > >> [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC.MP > >> real mem = 2066206720 (1970MB) > >> avail mem = 2006016000 (1913MB) > >> mainbus0 at root > >> bios0 at mainbus0: SMBIOS rev. 2.2 @ 0xf0000 (46 entries) > >> bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 06/12/2007 > >> acpi0 at bios0: rev 0 > >> acpi0: tables DSDT FACP SSDT _HPT MCFG APIC > >> acpi0: wakeup devices HUB0(S5) XVR0(S5) XVR1(S5) XVR2(S5) UAR1(S5) > >> UAR2(S5) USB0(S3) USB2(S3) AZAD(S5) MMAC(S5) > >> acpitimer0 at acpi0: 3579545 Hz, 24 bits > >> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > >> cpu0 at mainbus0: apid 0 (boot processor) > >> cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4000+, 2110.06 MHz > >> cpu0: > >> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > >> cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > >> 64b/line 16-way L2 cache > >> cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully > >> associative > >> cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully > >> associative > >> cpu0: apic clock running at 200MHz > >> cpu1 at mainbus0: apid 1 (application processor) > >> cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 4000+, 2109.72 MHz > >> cpu1: > >> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > >> cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > >> 64b/line 16-way L2 cache > >> cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully > >> associative > >> cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully > >> associative > >> ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 11, 24 pins > >> ioapic0: misconfigured as apic 0, remapped to apid 2 > >> acpiprt0 at acpi0: bus 0 (PCI0) > >> acpiprt1 at acpi0: bus 1 (HUB0) > >> acpicpu0 at acpi0: PSS > >> acpicpu1 at acpi0: PSS > >> acpitz0 at acpi0: critical temperature 124 degC > >> acpibtn0 at acpi0: PWRB > >> cpu0: PowerNow! K8 2109 MHz: speeds: 2100 2000 1800 1000 MHz > >> pci0 at mainbus0 bus 0: configuration mode 1 > >> "NVIDIA MCP61 Memory" rev 0xa1 at pci0 dev 0 function 0 not configured > >> pcib0 at pci0 dev 1 function 0 "NVIDIA MCP61 ISA" rev 0xa2 > >> nviic0 at pci0 dev 1 function 1 "NVIDIA MCP61 SMBus" rev 0xa2 > >> iic0 at nviic0 > >> spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5 > >> spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-5300CL5 > >> iic1 at nviic0 > >> "NVIDIA MCP61 Memory" rev 0xa2 at pci0 dev 1 function 2 not configured > >> "NVIDIA MCP61 SMU" rev 0xa2 at pci0 dev 1 function 3 not configured > >> ohci0 at pci0 dev 2 function 0 "NVIDIA MCP61 USB" rev 0xa2: apic 2 int > >> 11 (irq 11), version 1.0, legacy support > >> ehci0 at pci0 dev 2 function 1 "NVIDIA MPC61 USB" rev 0xa2: apic 2 int 5 > >> (irq 5) > >> usb0 at ehci0: USB revision 2.0 > >> uhub0 at usb0 "NVIDIA EHCI root hub" rev 2.00/1.00 addr 1 > >> ppb0 at pci0 dev 4 function 0 "NVIDIA MCP61" rev 0xa1 > >> pci1 at ppb0 bus 1 > >> skc0 at pci1 dev 5 function 0 "D-Link Systems DGE-530T B1" rev 0x11, > >> Yukon Lite (0x9): apic 2 int 5 (irq 5) > >> sk0 at skc0 port A: address 00:1b:11:1a:2e:98 > >> eephy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5 > >> ami0 at pci1 dev 6 function 0 "Symbios Logic MegaRAID" rev 0x01: apic > >> 2 int 10 (irq 10) > >> ami0: LSI 523, 32b, FW 713S, BIOS vG121, 64MB RAM > >> ami0: 1 channels, 0 FC loops, 1 logical drives > >> scsibus0 at ami0: 40 targets, initiator 40 > >> sd0 at scsibus0 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/direct fixed > >> sd0: 915723MB, 116738 cyl, 255 head, 63 sec, 512 bytes/sec, 1875400704 sec > >> total > >> scsibus1 at ami0: 16 targets, initiator 16 > >> pciide0 at pci0 dev 6 function 0 "NVIDIA MCP61 IDE" rev 0xa2: DMA, > >> channel 0 configured to compatibility, channel 1 configured to > >> compatibility > >> pciide0: channel 0 disabled (no drives) > >> pciide0: channel 1 ignored (disabled) > >> nfe0 at pci0 dev 7 function 0 "NVIDIA MCP61 LAN" rev 0xa2: apic 2 int > >> 10 (irq 10), address 00:19:21:fc:c2:5b > >> ukphy0 at nfe0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI > >> 0x0050ef, model 0x0007 > >> pciide1 at pci0 dev 8 function 0 "NVIDIA MCP61 SATA" rev 0xa2: DMA > >> pciide1: using apic 2 int 11 (irq 11) for native-PCI interrupt > >> wd0 at pciide1 channel 1 drive 0: <MTRON MSD-SATA3035> > >> wd0: 1-sector PIO, LBA, 15260MB, 31252480 sectors > >> wd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 6 > >> ppb1 at pci0 dev 9 function 0 "NVIDIA MCP61 PCIE" rev 0xa2 > >> pci2 at ppb1 bus 2 > >> ppb2 at pci0 dev 11 function 0 "NVIDIA MCP61 PCIE" rev 0xa2 > >> pci3 at ppb2 bus 3 > >> ppb3 at pci0 dev 12 function 0 "NVIDIA MCP61 PCIE" rev 0xa2 > >> pci4 at ppb3 bus 4 > >> vga1 at pci0 dev 13 function 0 "NVIDIA GeForce 6100 nForce 405" rev 0xa2 > >> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > >> wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > >> pchb0 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00 > >> pchb1 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00 > >> pchb2 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00 > >> kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: > >> core rev BH-G1 > >> isa0 at pcib0 > >> isadma0 at isa0 > >> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > >> pckbc0 at isa0 port 0x60/5 > >> pckbd0 at pckbc0 (kbd slot) > >> pckbc0: using irq 1 for kbd slot > >> wskbd0 at pckbd0: console keyboard, using wsdisplay0 > >> pcppi0 at isa0 port 0x61 > >> midi0 at pcppi0: <PC speaker> > >> spkr0 at pcppi0 > >> lpt0 at isa0 port 0x378/4 irq 7 > >> it0 at isa0 port 0x2e/2: IT8726F rev 0x01, EC port 0x290 > >> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > >> usb1 at ohci0: USB revision 1.0 > >> uhub1 at usb1 "NVIDIA OHCI root hub" rev 1.00/1.00 addr 1 > >> mtrr: Pentium Pro MTRR support > >> uhidev0 at uhub1 port 4 configuration 1 interface 0 "CHICONY HP Basic > >> USB Keyboard" rev 1.10/3.00 addr 2 > >> uhidev0: iclass 3/1 > >> ukbd0 at uhidev0: 8 modifier keys, 6 key codes > >> wskbd1 at ukbd0 mux 1 > >> wskbd1: connecting to wsdisplay0 > >> softraid0 at root > >> root on wd0a swap on wd0b dump on wd0b > >> > >> > >> Please CC me on replies as I'm not subscribed. Enjoy! > >> Brandon
