Hi,
I installed 4.3-release on an O2 and noticed that it is quite slow
compared to 4.1-stable.
For example, it took more than 5 hours to build a kernel, that's about
the same as my Vax ;-)
Right now I'm running a make build and it is dead slow. Load is around
0.10 and top shows that the machine is nearly 100% idle. It seems that
something is delaying the system, but I can't tell what it is. Some
kind of interrupt problem, perhaps?
BTW: /usr/src is NFS-mounted, but that shouldn't be a problem, right?
Any pointers are appreciated.
Maurice
[ using 302776 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.3 (GENERIC) #0: Fri May 2 06:27:48 CEST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 268435456 (256MB)
rsvd mem = 7020544 (6MB)
avail mem = 243376128 (232MB)
mainbus0 at root
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 200 MHz with R5000 based FPC rev 1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 1024KB direct
macebus0 at mainbus0: crime rev 10.1
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
sd0 at scsibus0 targ 1 lun 0: <SGI, IBM DDRS-39130W, S95D> SCSI2 0/direct fixed
sd0: 8682MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sec, 17781520 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 1036> SCSI2 5/cdrom
removable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register
com0 at macebus0 base 0x00390000 irq 5: ns16550a, 16 byte fifo
com0: console
com1 at macebus0 base 0x00398000 irq 5: ns16550a, 16 byte fifo
mec0 at macebus0 base 0x00280000 irq 4: MAC-110 rev 1, address 08:00:69:0c:98:8e
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 0
mavb0 at macebus0 base 0x00300000 irq 7: AD1843 rev 1
audio0 at mavb0
mkbc0 at macebus0 base 0x00320000 irq 6
power0 at macebus0 irq 6
gbe0 at mainbus0: device has not been setup by firmware!
softraid0 at root
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
boot device: sd0
root on sd0a swap on sd0b dump on sd0b
