Grabed today's current bsd.rd and pxeboot to do an install on a
soekris 4801. It panics before getting to installer:
comBIOS Monitor. Press ? for help.
> boot f0
NSC DP83815/DP83816 Fast Ethernet UNDI, v1.03
Copyright (C) 2002, 2003 National Semiconductor Corporation
All rights reserved.
Pre-boot eXecution Environment PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation
CLIENT MAC ADDR: 00 00 24 C3 8B C0
CLIENT IP: 192.168.10.7 MASK: 255.255.255.0 DHCP IP: 192.168.10.4
GATEWAY IP: 192.168.10.8
probing: pc0 com0 com1 pci pxe![2.1] mem[639K 127M a20=on]
disk: hd0+
net: mac 00:00:24:c3:8b:c0, ip 192.168.10.7, server 192.168.10.4
>> OpenBSD/i386 PXEBOOT 2.02
switching console to com0
com0: changing speed to 9600 baud in 5 seconds, change your terminal
to match!
com0: 9600 baud
>> OpenBSD/i386 PXEBOOT 2.02
com0: 9600 baud
boot> boot bsd.rd
booting tftp:bsd.rd: 4998132+874200 [52+190624+176480]=0x5f3674
entry point at 0x200120
?
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.3-current (RAMDISK_CD) #680: Sat Apr 12 15:27:58 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133787648 (127MB)
avail mem = 122974208 (117MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/40/21, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:8b:c0
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:8b:c1
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:8b:c2
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
iwi0 at pci0 dev 14 function 0 "Intel PRO/Wireless 2915ABG" rev 0x05:
irq 11, address 00:13:ce:b5:bc:88
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-256>
wd0: 1-sector PIO, LBA, 244MB, 500400 sectors
wd0(pciide0:0:0): using PIO mode 4
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5,
version 1.0, legacy support
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask f3e5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
PXE boot MAC address 00:00:24:c3:8b:c0, interface sis0
nfs_boot: using interface sis0, with revarp & bootparams
panic: revarp failed, error=51
syncing disks... done
rebooting...
POST: 0123456789bcefghipajklnoq,,,tvwxy
