Anyone have success installing OpenBSD on a Sunfire 280R?
I'm currently getting the following information... A bug has been filed
for this issue.
--
halted
Program terminated
{0} ok boot net bsd.rd
Resetting ...
RSC Alert: Host System has Reset
@(#)OBP 4.5.10 2002/02/11 10:39 Sun Fire 280R
BBC AID Register 0000.0000.0000.0000
Reset: 0000.0000.0000.0010SPOR
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0001.0000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Copy Done
PC = 0000.07ff.f008.5970
PC = 0000.0000.0000.59e8
Decompressing Done
Size = 0000.0000.0006.f8b0
ttya initialized
Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (900 MHz @ 6:1, 8 MB)
memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (900 MHz @ 6:1, 8 MB)
memory-controller
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
temperature fan-control motherboard-fru ioexp ioexp ioexp
fcal-backplane remote-system-console power-distribution-board
power-supply power-supply rscrtc beep rtc gpio pmc parallel
rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (900 MHz @ 6:1, 8 MB)
memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (900 MHz @ 6:1, 8 MB)
memory-controller
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
temperature fan-control motherboard-fru ioexp ioexp ioexp
fcal-backplane remote-system-console power-distribution-board
power-supply power-supply rscrtc beep rtc gpio pmc parallel
rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Sun Fire 280R (2 X UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 4096 MB memory installed, Serial #51537657.
Ethernet address 0:3:ba:12:66:f9, Host ID: 831266f9.
Rebooting with command: boot net bsd.rd
Boot device: /[EMAIL PROTECTED],700000/[EMAIL PROTECTED],1: File and args:
bsd.rd
Timeout waiting for ARP/RARP packet
10600 >> OpenBSD BOOT 1.2
Using BOOTPARAMS protocol: ip address: 192.168.31.240, hostname: penny
root addr=192.168.31.210 path=/home/jumpstart/
Booting /[EMAIL PROTECTED],700000/[EMAIL PROTECTED],1/bsd.rd
[EMAIL PROTECTED]@[EMAIL PROTECTED]
symbols @ 0xfefd6200 52 start=0x1000000
console is /[EMAIL PROTECTED],700000/[EMAIL PROTECTED]/[EMAIL PROTECTED],3083f8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.3-current (RAMDISK) #268: Fri Apr 11 16:51:42 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/sparc64/compile/RAMDISK
real mem = 4294967296 (4096MB)
avail mem = 4148641792 (3956MB)
mainbus0 at root: Sun Fire 280R (2 X UltraSPARC-III+)
cpu0 at mainbus0: SUNW,UltraSPARC-III+ (rev 2.2) @ 900 MHz
cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 8192K
external (512 b/l)
"SUNW,UltraSPARC-III+" at mainbus0 not configured
"memory-controller" at mainbus0 not configured
"memory-controller" at mainbus0 not configured
schizo0 at mainbus0: "Schizo", version 4, ign 200, bus B 0 to 1
schizo0: dvma map c0000000-ffffffff, iotdb 5c1c000-5d1c000
pci0 at schizo0
ebus0 at pci0 dev 5 function 0 "Sun RIO EBus" rev 0x01
"flashprom" at ebus0 addr 0-1fffff not configured
"bbc" at ebus0 addr 0-fffff not configured
"power" at ebus0 addr 30002e-30002f, 300600-300607 not configured
"i2c" at ebus0 addr 2e-2f, 2d-2d ivec 0x23 not configured
"i2c" at ebus0 addr 30-31 ivec 0x23 not configured
"beep" at ebus0 addr 32-37 not configured
rtc0 at ebus0 addr 300070-300071 ivec 0x24: ds1287
"gpio" at ebus0 addr 300600-300607 not configured
"pmc" at ebus0 addr 300700-300701 not configured
"parallel" at ebus0 addr 300278-300287, 30002e-30002f, 700000-70000f
ivec 0x1c not configured
"rsc-control" at ebus0 addr 3062f8-3062ff ivec 0x2e not configured
com0 at ebus0 addr 3083f8-3083ff ivec 0x2d: ns16550a, 16 byte fifo
com0: console
sab0 at ebus0 addr 400000-40007f ivec 0x22: rev 3.2
sabtty0 at sab0 port 0
sabtty1 at sab0 port 1
gem0 at pci0 dev 5 function 1 "Sun ERI Ether" rev 0x01: ivec 0x21d,
address 00:03:ba:12:66:f9
luphy0 at gem0 phy 1: LU6612 10/100 PHY, rev. 1
ohci0 at pci0 dev 5 function 3 "Sun USB" rev 0x01: ivec 0x21f, version
1.0, legacy support
siop0 at pci0 dev 6 function 0 "Symbios Logic 53c875" rev 0x37: ivec
0x218, using 4K of on-board RAM
scsibus0 at siop0: 16 targets
cd0 at scsibus0 targ 6 lun 0: <TOSHIBA, DVD-ROM SD-M1401, 1009> SCSI2
5/cdrom removable
siop1 at pci0 dev 6 function 1 "Symbios Logic 53c875" rev 0x37: ivec
0x219, using 4K of on-board RAM
scsibus1 at siop1: 16 targets
sd0 at scsibus1 targ 10 lun 0: <SEAGATE, ST336605LSUN36G, 0238> SCSI3
0/direct fixed
sd0: 34732MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sec, 71132959 sec total
sd1 at scsibus1 targ 11 lun 0: <SEAGATE, ST336605LSUN36G, 0238> SCSI3
0/direct fixed
sd1: 34732MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sec, 71132959 sec total
sd2 at scsibus1 targ 12 lun 0: <SEAGATE, ST336605LSUN36G, 0238> SCSI3
0/direct fixed
sd2: 34732MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sec, 71132959 sec total
ppb0 at pci0 dev 1 function 0 "Intel S21154AE/BE PCI-PCI" rev 0x00
pci1 at ppb0 bus 1
"Sun PCIO EBus2" rev 0x01 at pci1 dev 0 function 0 not configured
hme0 at pci1 dev 0 function 1 "Sun HME" rev 0x01: ivec 0x20d, address
00:03:ba:03:22:51
luphy1 at hme0 phy 1: LU6612 10/100 PHY, rev. 1
"Sun PCIO EBus2" rev 0x01 at pci1 dev 1 function 0 not configured
hme1 at pci1 dev 1 function 1 "Sun HME" rev 0x01: ivec 0x20e, address
00:03:ba:03:22:52
luphy2 at hme1 phy 1: LU6612 10/100 PHY, rev. 1
"Sun PCIO EBus2" rev 0x01 at pci1 dev 2 function 0 not configured
hme2 at pci1 dev 2 function 1 "Sun HME" rev 0x01: ivec 0x20f, address
00:03:ba:03:22:53
luphy3 at hme2 phy 1: LU6612 10/100 PHY, rev. 1
"Sun PCIO EBus2" rev 0x01 at pci1 dev 3 function 0 not configured
hme3 at pci1 dev 3 function 1 "Sun HME" rev 0x01: ivec 0x20c, address
00:03:ba:03:22:54
luphy4 at hme3 phy 1: LU6612 10/100 PHY, rev. 1
"Emulex Light Pulse 8000" rev 0x02 at pci0 dev 3 function 0 not configured
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Sun OHCI root hub" rev 1.00/1.00 addr 1
schizo1 at mainbus0: "Schizo", version 4, ign 200, bus A 0 to 1
schizo1: dvma map c0000000-ffffffff, iotdb 605e000-615e000
pci2 at schizo1
isp0 at pci2 dev 4 function 0 "QLogic ISP2200" rev 0x05: ivec 0x204
scsibus2 at isp0: 256 targets
sd3 at scsibus2 targ 0 lun 0: <SEAGATE, ST373405FSUN72G, 0438> SCSI3
0/direct fixed
sd3: 70007MB, 14089 cyl, 24 head, 424 sec, 512 bytes/sec, 143374738 sec
total
sd4 at scsibus2 targ 1 lun 0: <SEAGATE, ST373405FSUN72G, 0438> SCSI3
0/direct fixed
sd4: 70007MB, 14089 cyl, 24 head, 424 sec, 512 bytes/sec, 143374738 sec
total
ppb1 at pci2 dev 1 function 0 "DEC 21154 PCI-PCI" rev 0x05
pci3 at ppb1 bus 1
isp1 at pci3 dev 4 function 0 "QLogic ISP10160" rev 0x06: ivec 0x200
data error type 32 sfsr=808008 sfva=f009681d afsr=10080000000000
afva=7ffed0010f0 tf=0x1c08d80
panic: data fault: pc=1162dd0 addr=f009681d sfsr=808008<TM,PRIV>
halted
Program terminated
{0} ok
