If you use acpi with -current it should reboot via acpi. Try disable apm via doing the following at the boot prompt. boot -c disable apm quit
This can be made more permanent via config(8). On Thu, Dec 20, 2007 at 06:41:05PM +0700, Ilya A. Kovalenko wrote: > Good time of day, > > ------------------------- > orphan# uname -a > OpenBSD orphan.oganer.net 4.2 GENERIC#0 i386 > orphan# reboot > /etc/rc.shutdown in progress... > /etc/rc.shutdown complete. > syncing disks... done > rebooting... > *HANG* > ------------------------- > > same on latest snapshot kernel (w/ -stable userland) > halt(8) works fine, > strl-Alt-Del (before kernel boot) works fine > BIOS Setup defaults reset does not help > > some kernel debugging: > printf() control points on cpu_reset(): > ------------------------- > syncing disks... done > rebooting... > cpu_reset(): disabling IRQs ... > cpu_reset(): calling (*cpuresetfn)() ... > cpu_reset(): hacking keyboard ... > *HANG* > ------------------------- > > comment out keyboard controller code: > ------------------------- > syncing disks... done > rebooting... > cpu_reset(): disabling IRQs ... > cpu_reset(): calling (*cpuresetfn)() ... > cpu_reset(): hacking keyboard (disabled) ... > cpu_reset(): causing triple fault by IDT ... > *HANG* > ------------------------- > > comment out IDT invalidation code: > ------------------------- > syncing disks... done > rebooting... > cpu_reset(): disabling IRQs ... > cpu_reset(): calling (*cpuresetfn)() ... > cpu_reset(): hacking keyboard (disabled) ... > cpu_reset(): causing triple fault by IDT (disabled) ... > cpu_reset(): causing triple fault by address space unmap ... > cpu_reset(): entering infinite loop ... > *HANG* > ------------------------- > > Any clue ? > Faulty hardware ? (looking for identical hardware to test) > > Kind regards, > > Ilya A. Kovalenko (mailto:[EMAIL PROTECTED]) > SpecialEQ SW section > JSC Oganer-Service > > P.S. dmesg (latest snapshot): > > OpenBSD 4.2-current (GENERIC) #607: Tue Dec 18 18:36:52 MST 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel(R) Celeron(R) CPU 2.53GHz ("GenuineIntel" 686-class) 2.54 GHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CNXT-ID,CX16,xTPR > real mem = 502820864 (479MB) > avail mem = 478240768 (456MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 10/27/05, BIOS32 rev. 0 @ 0xfbf60, > SMBIOS rev. 2.2 @ 0xf0000 (33 entries) > bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 10/27/2005 > apm0 at bios0: Power Management spec V1.2 (slowidle) > apm0: AC on, battery charge unknown > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdef4 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde50/160 (8 entries) > pcibios0: PCI Exclusive IRQs: 5 9 10 11 > pcibios0: PCI Interrupt Router at 000:02:0 ("SiS 85C503 System" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x8000! 0xd0000/0x1800 0xd2000/0x1800 > 0xd4000/0x1800 0xef000/0x1000! > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > pchb0 at pci0 dev 0 function 0 "SiS 661 PCI" rev 0x11 > agp0 at pchb0: aperture at 0xd0000000, size 0x8000000 > ppb0 at pci0 dev 1 function 0 "SiS 648FX AGP" rev 0x00 > pci1 at ppb0 bus 1 > vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x00 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pcib0 at pci0 dev 2 function 0 "SiS 964 ISA" rev 0x36 > pciide0 at pci0 dev 2 function 5 "SiS 5513 EIDE" rev 0x01: 661: DMA, channel > 0 configured to compatibility, channel 1 configured to compatibility > wd0 at pciide0 channel 0 drive 0: <WDC WD800BB-22JHC0> > wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 > pciide0: channel 1 disabled (no drives) > auich0 at pci0 dev 2 function 7 "SiS 7012 AC97" rev 0xa0: irq 5, SiS7012 AC97 > ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0) > audio0 at auich0 > ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: irq 5, version > 1.0, legacy support > ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: irq 10, version > 1.0, legacy support > ohci2 at pci0 dev 3 function 2 "SiS 5597/5598 USB" rev 0x0f: irq 11, version > 1.0, legacy support > ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: irq 9 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "SiS EHCI root hub" rev 2.00/1.00 addr 1 > sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91: irq 10, > address 00:14:2a:f7:30:dd > rlphy0 at sis0 phy 9: RTL8201L 10/100 PHY, rev. 1 > pciide1 at pci0 dev 5 function 0 "SiS 180 SATA" rev 0x01: DMA > pciide1: using irq 11 for native-PCI interrupt > em0 at pci0 dev 9 function 0 "Intel PRO/1000MT (82540EM)" rev 0x02: irq 11, > address 00:07:e9:2a:a0:74 > em1 at pci0 dev 10 function 0 "Intel PRO/1000MT (82540EM)" rev 0x02: irq 5, > address 00:07:e9:2a:9f:9b > em2 at pci0 dev 11 function 0 "Intel PRO/1000MT (82540EM)" rev 0x02: irq 10, > address 00:07:e9:2a:a2:a5 > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > it0 at isa0 port 0x2e/2: IT8705F rev 0x03, EC port 0x290 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1 > usb2 at ohci1: USB revision 1.0 > uhub2 at usb2 "SiS OHCI root hub" rev 1.00/1.00 addr 1 > usb3 at ohci2: USB revision 1.0 > uhub3 at usb3 "SiS OHCI root hub" rev 1.00/1.00 addr 1 > biomask ff65 netmask ff65 ttymask ffe7 > mtrr: Pentium Pro MTRR support > uhidev0 at uhub1 port 2 configuration 1 interface 0 "vendor 0x10d5 UKU-M02 > 1.7" rev 1.10/0.00 addr 2 > uhidev0: iclass 3/1 > ukbd0 at uhidev0: 8 modifier keys, 6 key codes > wskbd1 at ukbd0 mux 1 > wskbd1: connecting to wsdisplay0 > uhidev1 at uhub1 port 2 configuration 1 interface 1 "vendor 0x10d5 UKU-M02 > 1.7" rev 1.10/0.00 addr 2 > uhidev1: iclass 3/1, 3 report ids > ums0 at uhidev1 reportid 1: 5 buttons and Z dir. > wsmouse0 at ums0 mux 0 > uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0 > uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0 > softraid0 at root > root on wd0a swap on wd0b dump on wd0b
