I just installed 4.1 and I get a screen full of dc0: failed to force
tx and rx to idle state
I thought it might be a harmless annoyance but after awhile
the thing drops into the debugger
I missed the exact message it gave.
I was hoping it would do it again before I have to leave but it hasn't
I googled but didn't find a solution.
I have cut and pasted the output from ifconfig and dmesg below.
I do have a non tulip nic I might try tomorrow.
Any suggestions?
ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33208
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
dc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:a0:cc:da:bf:8e
groups: egress
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::2a0:ccff:feda:bf8e%dc0 prefixlen 64 scopeid 0x1
inet 192.168.1.65 netmask 0xffffff00 broadcast 192.168.1.255
enc0: flags=0<> mtu 1536
OpenBSD 4.2 (GENERIC) #375: Tue Aug 28 10:38:44 MDT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 334 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 267939840 (255MB)
avail mem = 251437056 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 09/08/98, BIOS32 rev. 0 @
0xfb1f0, SMBIOS rev. 2.1 @ 0xf0800 (28 entries)
bios0: vendor Award Software International, Inc. version "4.51 PG" date 09/08/98
bios0: First International Computer, Inc. Product Name
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb66c
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdcc0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C597 PCI" rev 0x01
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6326 VGA" rev 0xd1: aperture at
0xe7000000, size 0x400000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C596A ISA" rev 0x05
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA33,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <QUANTUM Bigfoot TX8.0AT>
wd0: 16-sector PIO, LBA, 7665MB, 15698592 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CD-RW GCE-8240B, 1.06> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
"VIA VT82C596 Power" rev 0x00 at pci0 dev 7 function 3 not configured
dc0 at pci0 dev 9 function 0 "Lite-On PNIC" rev 0x20: irq 10, address
00:a0:cc:da:bf:8e
bmtphy0 at dc0 phy 1: BCM5201 10/100 PHY, rev. 2
eso0 at pci0 dev 11 function 0 "ESS SOLO-1 AudioDrive" rev 0x01: ES1946, irq 5
audio0 at eso0
opl0 at eso0: model OPL3
midi0 at opl0: <ESO Yamaha OPL3>
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
eso0: mapping Audio 1 DMA using I/O space at 0x410
biomask eb45 netmask ef45 ttymask ffc7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
--
Email [EMAIL PROTECTED] If you want a gmail invitation just ask.
Amateur Radio AD5DU.
home page http://www.geocities.com/richard_mccombs/
