hi list,

i thought i would set up a small machine that would manage the adsl link and also would be a wireless accesspoint. i bought a via epia board for that that has one pci slot, one on board ethernet interface (vr) and one pcmci slot. a searched for a pcmcia card that is supported and found one: gigabyte air crouser g (gn-wmkg).

after i inserted that card the kernel noted me it has new device attached (ral0). if i remove the card then i got a "ral0 detached" message but if i reinsert it there is no any message and the interface is still gone.

if i don't remove the card after a fresh boot i just start getting the "ral0: device timeout" messages and after like ten minutes with no any activity at all on that machine the epia boots itself.

my question would be how to produce some more information to be able to find out what the problem is with the ral driver.

here i attach the dmesg of the 4.1-release when ral was inserted at boottime:

OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007
   [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: VIA Samuel 2 ("CentaurHauls" 686-class) 600 MHz
cpu0: FPU,DE,TSC,MSR,MTRR,PGE,MMX
real mem  = 502824960 (491040K)
avail mem = 451014656 (440444K)
using 4278 buffers containing 25264128 bytes (24672K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 01/06/04, BIOS32 rev. 0 @ 0xfb280, SMBIOS rev. 2.2 @ 0xf0800 (26 entries)
bios0: VIA Technologies, Inc. CLE266-8235
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf44
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfded0/112 (5 entries)
pcibios0: PCI Exclusive IRQs: 5 9 12
pcibios0: PCI Interrupt Router at 000:17:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xe000 0xd0000/0x8000!
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8623 PCI" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8633 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA CLE266" rev 0x03: aperture at 0xd8000000, size 0x10000000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
cbb0 at pci0 dev 10 function 0 "Ricoh 5C476 CardBus" rev 0x80: irq 12
cbb1 at pci0 dev 10 function 1 "Ricoh 5C476 CardBus" rev 0x80: irq 9
"VIA VT6306 FireWire" rev 0x80 at pci0 dev 13 function 0 not configured
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x80: irq 12
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0x80: irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0x80: irq 5
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 16 function 3 "VIA VT6202 USB" rev 0x82: irq 12
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: VIA EHCI root hub, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
viapm0 at pci0 dev 17 function 0 "VIA VT8235 ISA" rev 0x00
iic0 at viapm0
pciide0 at pci0 dev 17 function 1 "VIA VT82C571 IDE" rev 0x06: ATA133, channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <SAMSUNG HD400LD>
wd0: 16-sector PIO, LBA48, 381554MB, 781422768 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
pciide0: channel 1 disabled (no drives)
auvia0 at pci0 dev 17 function 5 "VIA VT8233 AC97" rev 0x50: irq 5
ac97: codec id 0x49434552 (ICEnsemble VIA VT1616i)
ac97: codec features headphone, 18 bit DAC, 18 bit ADC, KS Waves 3D
audio0 at auvia0
vr0 at pci0 dev 18 function 0 "VIA RhineII-2" rev 0x74: irq 12, address 00:40:63:da:fb:4a ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 8: OUI 0x004063, model 0x0032
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0 cacheline 0x0, lattimer 0x20
pcmcia1 at cardslot1
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
viasio0 at isa0 port 0x2e/2: VT1211 rev 0x02: HM WDG: not activated
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask ff65 netmask ff65 ttymask ffe7
pctr: user-level cycle counter enabled
ral0 at cardbus0 dev 0 function 0 "Ralink Technology, Inc., RT2500, 802.11 CardBus Reference Card": irq 12, address 00:1a:4d:22:2f:96
ral0: MAC/BBP RT2560 (rev 0x04), RF RT2525
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: vendor 0x0ede TOD USB Keyboard / PS2 Mouse, rev 1.10/0.01, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 1 configuration 1 interface 1
uhidev1: vendor 0x0ede TOD USB Keyboard / PS2 Mouse, rev 1.10/0.01, addr 2, iclass 3/1
uhidev1: 3 report ids
ums0 at uhidev1 reportid 1: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302

Reply via email to