When connecting a Nikon Coolpix L10 camera to my laptop via USB, no i
partition shows up:
$ sudo disklabel sd0
disklabel: warning, DOS partition table with no valid OpenBSD partition
# /dev/rsd0c:
type: SCSI
disk: SCSI disk
label: DSC COOLPIX L10
flags:
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 255
sectors/cylinder: 16065
cylinders: 250
total sectors: 4019904
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0 # microseconds
track-to-track seek: 0 # microseconds
drivedata: 0
16 partitions:
# size offset fstype [fsize bsize cpg]
c: 4019904 0 unused 0 0 # Cyl 0 -
250*
Obviously I cannot mount /dev/sd0i:
$ sudo mount -t msdos /dev/sd0i /mnt/flashmem
mount_msdos: /dev/sd0i on /mnt: Device not configured
fdisk shows:
$ sudo fdisk sd0
Disk: sd0 geometry: 250/255/63 [4019904 Sectors]
Offset: 0 Signature: 0xAA55
Starting Ending LBA Info:
#: id C H S - C H S [ start: size ]
------------------------------------------------------------------------
0: 06 0 3 55 - 250 95 37 [ 243: 4022029 ] DOS > 32MB
1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
3: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
Is there anything I can do to get the i partition to show up? I have no
problems using the camera in FreeBSD 6.2 and Windows XP.
dmesg follows (camera connect lines are at the bottom). Please ask if
you need me to supply more info.
Best regards,
Martin
OpenBSD 4.1-current (GENERIC) #2: Mon May 28 21:36:52 CEST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1600MHz ("GenuineIntel" 686-class) 1.60
GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,EST,TM2
real mem = 535785472 (510MB)
avail mem = 509038592 (485MB)
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 04/19/05, BIOS32 rev. 0 @ 0xfd750, SMBIOS
rev. 2.33 @ 0xe0010 (61 entries)
bios0: IBM 2373NG9
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 100%
apm0: AC on, battery charge high
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd6e0/0x920
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdea0/272 (15 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #6 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1000 0xdc000/0x4000!
0xe0000/0x10000
acpi at mainbus0 not configured
cpu0 at mainbus0
cpu0: Enhanced SpeedStep 1600 MHz (1484 mV): speeds: 1600, 1400, 1200, 1000,
800, 600 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82855PE Hub" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82855PE AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M9 Lf" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 11
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 11
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 11
usb0 at ehci0: USB revision 2.0
uhub0 at usb0
uhub0: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub0: 6 ports with 6 removable, self powered
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x81
pci2 at ppb1 bus 2
cbb0 at pci2 dev 0 function 0 "TI PCI4520 CardBus" rev 0x01: irq 11
cbb1 at pci2 dev 0 function 1 "TI PCI4520 CardBus" rev 0x01: irq 11
em0 at pci2 dev 1 function 0 "Intel PRO/1000MT (82540EP)" rev 0x03: irq 11,
address 00:11:25:44:6c:4a
ral0 at pci2 dev 2 function 0 "Ralink RT2561S" rev 0x00: irq 11, address
00:12:0e:61:81:1c
ral0: MAC/BBP RT2561C, RF RT5225
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8, lattimer 0xb0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 6 device 0 cacheline 0x8, lattimer 0xb0
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x01: 24-bit timer
at 3579545Hz
pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MHT2040AH>
wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR8083N, 0K04> SCSI0 5/cdrom
removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x01: irq 11
iic0 at ichiic0
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 11, ICH4
AC97
ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801DB Modem" rev 0x01 at pci0 dev 31 function 6 not configured
usb1 at uhci0: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
usb2 at uhci1: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
usb3 at uhci2: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
aps0 at isa0 port 0x1600/31
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
biomask effd netmask effd ttymask ffff
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b
auich0: measured ac97 link rate at 48005 Hz, will use 48000 Hz
umass0 detached
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: NIKON NIKON DSC COOLPIX L10, rev 2.00/0.00, addr 2
umass0: using ATAPI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <NIKON, DSC COOLPIX L10, > SCSI0 0/direct
removable
sd0: 1962MB, 250 cyl, 255 head, 63 sec, 512 bytes/sec, 4019904 sec total
