Hello,
Last update (~2 weeks ago) and the one from last night result in
sensorsd shutting down my PC within 2 to 4 minutes after booting up.
Now /etc/sensorsd.conf has an entry in it that I added to safely
shut the computer down if the CPU gets too hot. The only problem is
that sensorsd keeps shutting the computer down even though the
temperature displayed using systat -w 1 sensors shows the cpu to be
a good 8 to 10 degrees cooler than the conditional temperature!
Perhaps the temperature is spiking at some point between systat
updating itself?
Anyhow, here are the relevant /etc/sensorsd.conf and dmesg. Thanks
and let me know if there's anymore information that I can (should)
include.
# $OpenBSD: sensorsd.conf,v 1.1 2003/10/08 20:30:04 grange Exp $
#
# Sample sensorsd.conf file. See sensorsd.conf(5) for details.
#
# +5 voltage (volts)
#hw.sensors.3:low=4.8V:high=5.2V
# +12 voltage (volts)
#hw.sensors.4:low=11.5V:high=12.5V
# Chipset temperature (degrees Celsius)
#hw.sensors.7:high=50C
# CPU temperature (degrees Celsius)
hw.sensors.viaenv0.temp0:high=70C:command=/sbin/shutdown -hp now "System
overheating! Emergency Shutdown!"
# CPU fan (RPM)
#hw.sensors.3:low=5000
OpenBSD 4.1-current (GENERIC) #178: Fri May 25 03:22:20 MDT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Athlon(tm) processor ("AuthenticAMD" 686-class, 256KB L2 cache) 1.20
GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 804810752 (767MB)
avail mem = 726335488 (692MB)
using 4278 buffers containing 40366080 bytes (39420K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 07/13/01, BIOS32 rev. 0 @ 0xfb5d0, SMBIOS
rev. 2.2 @ 0xf0800 (38 entries)
bios0: Gigabyte Technology Co., LTD 7DXR
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xde74
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfddb0/192 (10 entries)
pcibios0: PCI Exclusive IRQs: 5 7 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xcc000/0x4000! 0xd0000/0x4000
acpi0 at mainbus0: rev 0
acpi0: tables DSDT FACP
acpitimer at acpi0 not configured
acpiprt0 at acpi0: bus 0 (PCI0)
acpicpu at acpi0 not configured
acpibtn at acpi0 not configured
acpibtn at acpi0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "AMD 761 PCI" rev 0x13
ppb0 at pci0 dev 1 function 0 "AMD 761 PCI-PCI" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Mach64 GM" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y080L0>
wd0: 16-sector PIO, LBA, 78167MB, 160086528 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <ASUS, CD-S500/A, 1.2C> SCSI0 5/cdrom removable
atapiscsi1 at pciide0 channel 1 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <BENQ, CDRW 5232X, KPBY> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
cd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x1a: irq 11
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x1a: irq 11
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x40: failed to map
PM I/O space
dc0 at pci0 dev 10 function 0 "ADMtek AN983" rev 0x11: irq 5, address
00:10:a7:26:1d:3c
ukphy0 at dc0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI 0x000749,
model 0x0001
rl0 at pci0 dev 12 function 0 "D-Link Systems 530TX+" rev 0x10: irq 10, address
00:50:ba:59:24:c3
rlphy0 at rl0 phy 0: RTL internal PHY
eap0 at pci0 dev 14 function 0 "Ensoniq CT5880" rev 0x03: irq 5
ac97: codec id 0x83847608 (SigmaTel STAC9708/11)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at eap0
midi0 at eap0: <AudioPCI MIDI UART>
uhci2 at pci0 dev 15 function 0 "VIA VT83C572 USB" rev 0x50: irq 11
uhci3 at pci0 dev 15 function 1 "VIA VT83C572 USB" rev 0x50: irq 10
ehci0 at pci0 dev 15 function 2 "VIA VT6202 USB" rev 0x51: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0
uhub0: VIA EHCI root hub, rev 2.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pciide1 at pci0 dev 16 function 0 "Promise PDC20265" rev 0x02: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide1: using irq 11 for native-PCI interrupt
pciide1: channel 0 disabled (no drives)
pciide1: channel 1 disabled (no drives)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
usb1 at uhci0: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
usb2 at uhci1: USB revision 1.0
uhub2 at usb2
uhub2: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
usb3 at uhci2: USB revision 1.0
uhub3 at usb3
uhub3: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
usb4 at uhci3: USB revision 1.0
uhub4 at usb4
uhub4: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
biomask ffdd netmask fffd ttymask ffff
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: KidzMouse, Inc. - www.KidzMouse.com KidzMouse Optical Mouse, rev
1.10/0.01, addr 2, iclass 3/1
ugen0 at uhub3 port 2ums0 at uhidev0: 5 buttons and Z dir.
wsmouse0 at ums0 mux 0
ugen0: AGFA SNAPSCAN e40, rev 1.00/1.10, addr 2
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b
--
W. Steven Schneider <[EMAIL PROTECTED]>
