On Sat, May 05, 2007 at 09:38:02AM +0200, Little Red Riding Hood marching through the forest wrote: > Not sent to bugs@ because I'm not sure it could do much there. I'm hoping > someone may be able to give hints on what to check, so I can resolve this > small issue.
Why would you wanna do that?!!! can't you follow the precedure?!!!! WHY DO YOU THINK YOU'RE SPECIAL!??? > I have a directory with 8000 .jpg's. I run ImageMagick over these to cut out > a certain section in order to later make an .avi out of them. Yet my kernel > freezes up. Observed in X and in console. [1]No drop to DDB because the USB > keyboard is disabled from dropping into DDB (I do not have a serial console > device). Here is the script: > > --- > #!/bin/sh > > for i in 1*jpg; do > > convert -resize 1024x768 -extract 1200x1000+300+0 $i AA$i > done > -- You're a loser! > I've not experienced any freezeups on the previous kernel from a month ago, > so it may (or not) be from something that's changed since. Here is what > I've done to cross-check what the problem may be: > > * I checked source trees for anything that went in the last 5 weeks but did > not > find anything that may be the culprit at first glance. > * I've booted the kernel with boot -d in order to set break points (mainly wd > and ata stuff) because on my USB keyboard I cannot enter into DDB from > console. This is to debug. It didn't show anything when I stabbed into it. > * I've disabled nviic and other i2c stuff and that wasn't it. > * I've removed the only hardware card in the system in order to make sure > it's not the ahc driver. > * disabling apmd because of changes to hw_setperf code still froze the kernel. > > All finger pointings and penetrations into finding the problem have resulted > in a NO-GO and I still get Kernel FREEZE UPS! (Infinite loops?) see > reference [1] (can't drop to DDB). There are no messages in the logs about > any bad hardware. You know.. no matter what you say, you make no sense! I've been watching you, loser! And what I saw was that you restored the kernel and userland from last month! Ah yeah! And you were mumbling to yourself saying the deraadt(!) doesn't want you to go back (revert). Yet you broke that rule as well! DO YOU NEVER LEARN!?!!!!! Anyhow! watching you for a day now.. and your computer hasn't frozen up yet meaning perhaps that there is any new code for the last 30 days that causes the freeze ups!!! GET A LIFE PETER! SERIOUSLY! US SNOOPING DOGS DON'T HAVE TIME TO WATCH YOU LIKE THIS! -p > dmesg of current kernel > > OpenBSD 4.1-current (GENERIC) #970: Thu May 3 02:01:25 MDT 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC > real mem = 1073278976 (1048124K) > avail mem = 907788288 (886512K) > using 22937 buffers containing 107536384 bytes (105016K) of memory > mainbus0 (root) > bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xf0000 (39 entries) > bios0: MICRO-STAR INTERNATIONAL CO., LTD MS-7125 > acpi at mainbus0 not configured > cpu0 at mainbus0: (uniprocessor) > cpu0: AMD Athlon(tm) 64 Processor 3500+, 2211.57 MHz > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,NXE,MMXX,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > 64b/line 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: Cool'n'Quiet K8 2211 MHz: speeds: 2200 2000 1800 1000 MHz > cpu0: AMD errata 86, 89, 97, 104 present, BIOS upgrade may be required > pci0 at mainbus0 bus 0: configuration mode 1 > "NVIDIA nForce4 DDR" rev 0xa3 at pci0 dev 0 function 0 not configured > pcib0 at pci0 dev 1 function 0 "NVIDIA nForce4 ISA" rev 0xa3 > nviic0 at pci0 dev 1 function 1 "NVIDIA nForce4 SMBus" rev 0xa2 > iic0 at nviic0 > iic1 at nviic0 > iic1: addr 0x2f 00=84 01=0f 02=10 03=00 04=07 05=20 06=18 07=00 08=00 14=14 > 15=62 16=02 17=05 > ohci0 at pci0 dev 2 function 0 "NVIDIA nForce4 USB" rev 0xa2: irq 10, version > 1.0, legacy support > ehci0 at pci0 dev 2 function 1 "NVIDIA nForce4 USB" rev 0xa3: irq 11 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 > uhub0: NVIDIA EHCI root hub, rev 2.00/1.00, addr 1 > uhub0: 10 ports with 10 removable, self powered > auich0 at pci0 dev 4 function 0 "NVIDIA nForce4 AC97" rev 0xa2: irq 5, > nForce4 AC97 > ac97: codec id 0x414c4790 (Avance Logic ALC850 rev 0) > audio0 at auich0 > pciide0 at pci0 dev 6 function 0 "NVIDIA nForce4 IDE" rev 0xa2: DMA, channel > 0 configured to compatibility, channel 1 configured to compatibility > pciide0: channel 0 disabled (no drives) > atapiscsi0 at pciide0 channel 1 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <E-IDE, CD-ROM 40X/AKU, F02> SCSI0 5/cdrom > removable > cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 > pciide1 at pci0 dev 7 function 0 "NVIDIA nForce4 SATA" rev 0xa3: DMA > pciide1: using irq 10 for native-PCI interrupt > wd0 at pciide1 channel 0 drive 0: <SAMSUNG HD080HJ> > wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors > wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 > wd1 at pciide1 channel 1 drive 0: <SAMSUNG HD160JJ> > wd1: 16-sector PIO, LBA48, 152627MB, 312581808 sectors > wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5 > pciide2 at pci0 dev 8 function 0 "NVIDIA nForce4 SATA" rev 0xa3: DMA > pciide2: using irq 11 for native-PCI interrupt > atapiscsi1 at pciide2 channel 0 drive 0 > scsibus1 at atapiscsi1: 2 targets > cd1 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM GSA-H30N, 1.01> SCSI0 > 5/cdrom removable > cd1(pciide2:0:0): using PIO mode 4, Ultra-DMA mode 5 > ppb0 at pci0 dev 9 function 0 "NVIDIA nForce4 PCI-PCI" rev 0xa2 > pci1 at ppb0 bus 1 > nfe0 at pci0 dev 10 function 0 "NVIDIA CK804 LAN" rev 0xa3: irq 3, address > 00:0c:76:50:a9:48 > eephy0 at nfe0 phy 1: Marvell 88E1111 Gigabit PHY, rev. 2 > ppb1 at pci0 dev 11 function 0 "NVIDIA nForce4 PCIE" rev 0xa3 > pci2 at ppb1 bus 2 > ppb2 at pci0 dev 12 function 0 "NVIDIA nForce4 PCIE" rev 0xa3 > pci3 at ppb2 bus 3 > ppb3 at pci0 dev 13 function 0 "NVIDIA nForce4 PCIE" rev 0xa3 > pci4 at ppb3 bus 4 > ppb4 at pci0 dev 14 function 0 "NVIDIA nForce4 PCIE" rev 0xa3 > pci5 at ppb4 bus 5 > vga1 at pci5 dev 0 function 0 vendor "NVIDIA", unknown product 0x016a rev 0xa1 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00 > pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00 > pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00 > pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00 > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > lm0 at isa0 port 0x290/8: W83627THF > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 > uhub1: NVIDIA OHCI root hub, rev 1.00/1.00, addr 1 > uhub1: 10 ports with 10 removable, self powered > uplcom0 at uhub1 port 1 > uplcom0: ATEN International Serial, rev 1.10/0.01, addr 2 > ucom0 at uplcom0 > uhidev0 at uhub1 port 2 configuration 1 interface 0 > uhidev0: Logitech USB-PS/2 Optical Mouse, rev 2.00/20.00, addr 3, iclass 3/1 > ums0 at uhidev0: 3 buttons and Z dir. > wsmouse0 at ums0 mux 0 > uhub2 at uhub1 port 4 > uhub2: ALCOR macally Kbd Hub, rev 1.10/1.00, addr 4 > uhub2: 3 ports with 2 removable, bus powered > uhidev1 at uhub2 port 1 configuration 1 interface 0 > uhidev1: ALCOR macally Kbd Hub, rev 1.10/1.00, addr 5, iclass 3/1 > ukbd0 at uhidev1: 8 modifier keys, 6 key codes, country code 1 > wskbd1 at ukbd0 mux 1 > wskbd1: connecting to wsdisplay0 > uhub3 at uhub1 port 5 > uhub3: Atmel UHB124 hub, rev 1.10/3.00, addr 6 > uhub3: 4 ports with 4 removable, self powered > uscanner0 at uhub1 port 6 > uscanner0: EPSON EPSON Scanner, rev 1.10/1.00, addr 7 > dkcsum: wd0 matches BIOS drive 0x80 > dkcsum: wd1 matches BIOS drive 0x81 > root on wd0a > rootdev=0x0 rrootdev=0x300 rawdev=0x302 > WARNING: / was not properly unmounted > wd1(pciide1:1:0): timeout > type: ata > c_bcount: 0 > c_skip: 0 > wd1: flush cache command timeout > > dmesg of last kernel > > May 4 00:12:49 oberon /bsd: OpenBSD 4.1-current (OBERON) #2: Thu Apr 5 > 08:38:28 CEST 2007 > May 4 00:12:50 oberon /bsd: [EMAIL > PROTECTED]:/usr/src/sys/arch/amd64/compile/OBERON > May 4 00:12:50 oberon /bsd: real mem = 1073278976 (1048124K) > May 4 00:12:50 oberon /bsd: avail mem = 907837440 (886560K) > May 4 00:12:50 oberon /bsd: using 22937 buffers containing 107536384 bytes > (105016K) of memory > May 4 00:12:50 oberon /bsd: mainbus0 (root) > May 4 00:12:50 oberon /bsd: bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xf0000 (39 > entries) > May 4 00:12:50 oberon /bsd: bios0: MICRO-STAR INTERNATIONAL CO., LTD MS-7125 > May 4 00:12:50 oberon /bsd: acpi at mainbus0 not configured > May 4 00:12:50 oberon /bsd: cpu0 at mainbus0: (uniprocessor) > May 4 00:12:50 oberon /bsd: cpu0: AMD Athlon(tm) 64 Processor 3500+, 2211.58 > MHz > May 4 00:12:50 oberon /bsd: cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,NXE,MMXX,LONG,3DNOW2,3DNOW > May 4 00:12:50 oberon /bsd: cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line > 2-way D-cache, 512KB 64b/line 16-way L2 cache > May 4 00:12:50 oberon /bsd: cpu0: ITLB 32 4KB entries fully associative, 8 > 4MB entries fully associative > May 4 00:12:50 oberon /bsd: cpu0: DTLB 32 4KB entries fully associative, 8 > 4MB entries fully associative > May 4 00:12:50 oberon /bsd: cpu0: Cool'n'Quiet K8 2211 MHz: speeds: 2200 > 2000 1800 1000 MHz > May 4 00:12:50 oberon /bsd: cpu0: AMD errata 86, 89, 97, 104 present, BIOS > upgrade may be required > May 4 00:12:50 oberon /bsd: pci0 at mainbus0 bus 0: configuration mode 1 > May 4 00:12:50 oberon /bsd: "NVIDIA nForce4 DDR" rev 0xa3 at pci0 dev 0 > function 0 not configured > May 4 00:12:50 oberon /bsd: pcib0 at pci0 dev 1 function 0 "NVIDIA nForce4 > ISA" rev 0xa3 > May 4 00:12:50 oberon /bsd: nviic0 at pci0 dev 1 function 1 "NVIDIA nForce4 > SMBus" rev 0xa2 > May 4 00:12:50 oberon /bsd: iic0 at nviic0 > May 4 00:12:50 oberon /bsd: iic1 at nviic0 > May 4 00:12:50 oberon /bsd: iic1: addr 0x2f 00=84 01=0f 02=10 03=00 04=07 > 05=20 06=18 07=00 08=00 14=14 15=62 16=02 17=05 > May 4 00:12:50 oberon /bsd: ohci0 at pci0 dev 2 function 0 "NVIDIA nForce4 > USB" rev 0xa2: irq 12, version 1.0, legacy support > May 4 00:12:50 oberon /bsd: ehci0 at pci0 dev 2 function 1 "NVIDIA nForce4 > USB" rev 0xa3: irq 10 > May 4 00:12:50 oberon /bsd: usb0 at ehci0: USB revision 2.0 > May 4 00:12:50 oberon /bsd: uhub0 at usb0 > May 4 00:12:50 oberon /bsd: uhub0: NVIDIA EHCI root hub, rev 2.00/1.00, addr > 1 > May 4 00:12:50 oberon /bsd: uhub0: 10 ports with 10 removable, self powered > May 4 00:12:50 oberon /bsd: auich0 at pci0 dev 4 function 0 "NVIDIA nForce4 > AC97" rev 0xa2: irq 3, nForce4 AC97 > May 4 00:12:50 oberon /bsd: ac97: codec id 0x414c4790 (Avance Logic ALC850 > rev 0) > May 4 00:12:50 oberon /bsd: audio0 at auich0 > May 4 00:12:50 oberon /bsd: pciide0 at pci0 dev 6 function 0 "NVIDIA nForce4 > IDE" rev 0xa2: DMA, channel 0 configured to compatibility, channel 1 > configured to compatibility > May 4 00:12:50 oberon /bsd: pciide0: channel 0 disabled (no drives) > May 4 00:12:50 oberon /bsd: atapiscsi0 at pciide0 channel 1 drive 0 > May 4 00:12:50 oberon /bsd: scsibus0 at atapiscsi0: 2 targets > May 4 00:12:50 oberon /bsd: cd0 at scsibus0 targ 0 lun 0: <E-IDE, CD-ROM > 40X/AKU, F02> SCSI0 5/cdrom removable > May 4 00:12:50 oberon /bsd: cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 > May 4 00:12:50 oberon /bsd: pciide1 at pci0 dev 7 function 0 "NVIDIA nForce4 > SATA" rev 0xa3: DMA > May 4 00:12:50 oberon /bsd: pciide1: using irq 12 for native-PCI interrupt > May 4 00:12:50 oberon /bsd: wd0 at pciide1 channel 0 drive 0: <SAMSUNG > HD080HJ> > May 4 00:12:50 oberon /bsd: wd0: 16-sector PIO, LBA48, 76319MB, 156301488 > sectors > May 4 00:12:50 oberon /bsd: wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA > mode 5 > May 4 00:12:50 oberon /bsd: wd1 at pciide1 channel 1 drive 0: <SAMSUNG > HD160JJ> > May 4 00:12:50 oberon /bsd: wd1: 16-sector PIO, LBA48, 152627MB, 312581808 > sectors > May 4 00:12:50 oberon /bsd: wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA > mode 5 > May 4 00:12:50 oberon /bsd: pciide2 at pci0 dev 8 function 0 "NVIDIA nForce4 > SATA" rev 0xa3: DMA > May 4 00:12:50 oberon /bsd: pciide2: using irq 10 for native-PCI interrupt > May 4 00:12:50 oberon /bsd: atapiscsi1 at pciide2 channel 0 drive 0 > May 4 00:12:50 oberon /bsd: scsibus1 at atapiscsi1: 2 targets > May 4 00:12:50 oberon /bsd: cd1 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM > GSA-H30N, 1.01> SCSI0 5/cdrom removable > May 4 00:12:50 oberon /bsd: cd1(pciide2:0:0): using PIO mode 4, Ultra-DMA > mode 5 > May 4 00:12:50 oberon /bsd: ppb0 at pci0 dev 9 function 0 "NVIDIA nForce4 > PCI-PCI" rev 0xa2 > May 4 00:12:50 oberon /bsd: pci1 at ppb0 bus 1 > May 4 00:12:50 oberon /bsd: ahc0 at pci1 dev 7 function 0 "Adaptec > AHA-2940AU" rev 0x01: irq 11 > May 4 00:12:50 oberon /bsd: scsibus2 at ahc0: 8 targets > May 4 00:12:50 oberon /bsd: nfe0 at pci0 dev 10 function 0 "NVIDIA CK804 > LAN" rev 0xa3: irq 11, address 00:0c:76:50:a9:48 > May 4 00:12:50 oberon /bsd: eephy0 at nfe0 phy 1: Marvell 88E1111 Gigabit > PHY, rev. 2 > May 4 00:12:50 oberon /bsd: ppb1 at pci0 dev 11 function 0 "NVIDIA nForce4 > PCIE" rev 0xa3 > May 4 00:12:50 oberon /bsd: pci2 at ppb1 bus 2 > May 4 00:12:50 oberon /bsd: ppb2 at pci0 dev 12 function 0 "NVIDIA nForce4 > PCIE" rev 0xa3 > May 4 00:12:50 oberon /bsd: pci3 at ppb2 bus 3 > May 4 00:12:50 oberon /bsd: ppb3 at pci0 dev 13 function 0 "NVIDIA nForce4 > PCIE" rev 0xa3 > May 4 00:12:50 oberon /bsd: pci4 at ppb3 bus 4 > May 4 00:12:50 oberon /bsd: ppb4 at pci0 dev 14 function 0 "NVIDIA nForce4 > PCIE" rev 0xa3 > May 4 00:12:50 oberon /bsd: pci5 at ppb4 bus 5 > May 4 00:12:50 oberon /bsd: vga1 at pci5 dev 0 function 0 vendor "NVIDIA", > unknown product 0x016a rev 0xa1 > May 4 00:12:50 oberon /bsd: wsdisplay0 at vga1 mux 1: console (80x25, vt100 > emulation) > May 4 00:12:50 oberon /bsd: wsdisplay0: screen 1-5 added (80x25, vt100 > emulation) > May 4 00:12:50 oberon /bsd: pchb0 at pci0 dev 24 function 0 "AMD AMD64 > HyperTransport" rev 0x00 > May 4 00:12:50 oberon /bsd: pchb1 at pci0 dev 24 function 1 "AMD AMD64 > Address Map" rev 0x00 > May 4 00:12:50 oberon /bsd: pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM > Cfg" rev 0x00 > May 4 00:12:50 oberon /bsd: pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc > Cfg" rev 0x00 > May 4 00:12:50 oberon /bsd: isa0 at pcib0 > May 4 00:12:50 oberon /bsd: isadma0 at isa0 > May 4 00:12:50 oberon /bsd: com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 > byte fifo > May 4 00:12:50 oberon /bsd: pckbc0 at isa0 port 0x60/5 > May 4 00:12:50 oberon /bsd: pckbd0 at pckbc0 (kbd slot) > May 4 00:12:50 oberon /bsd: pckbc0: using irq 1 for kbd slot > May 4 00:12:50 oberon /bsd: wskbd0 at pckbd0: console keyboard, using > wsdisplay0 > May 4 00:12:50 oberon /bsd: pcppi0 at isa0 port 0x61 > May 4 00:12:50 oberon /bsd: midi0 at pcppi0: <PC speaker> > May 4 00:12:50 oberon /bsd: spkr0 at pcppi0 > May 4 00:12:50 oberon /bsd: lpt0 at isa0 port 0x378/4 irq 7 > May 4 00:12:50 oberon /bsd: lm0 at isa0 port 0x290/8: W83627THF > May 4 00:12:50 oberon /bsd: fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > May 4 00:12:50 oberon /bsd: fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 > sec > May 4 00:12:50 oberon /bsd: usb1 at ohci0: USB revision 1.0 > May 4 00:12:50 oberon /bsd: uhub1 at usb1 > May 4 00:12:50 oberon /bsd: uhub1: NVIDIA OHCI root hub, rev 1.00/1.00, addr > 1 > May 4 00:12:50 oberon /bsd: uhub1: 10 ports with 10 removable, self powered > May 4 00:12:50 oberon /bsd: uplcom0 at uhub1 port 1 > May 4 00:12:50 oberon /bsd: uplcom0: ATEN International Serial, rev > 1.10/0.01, addr 2 > May 4 00:12:50 oberon /bsd: ucom0 at uplcom0 > May 4 00:12:50 oberon /bsd: uhidev0 at uhub1 port 2 configuration 1 > interface 0 > May 4 00:12:50 oberon /bsd: uhidev0: Logitech USB-PS/2 Optical Mouse, rev > 2.00/20.00, addr 3, iclass 3/1 > May 4 00:12:50 oberon /bsd: ums0 at uhidev0: 3 buttons and Z dir. > May 4 00:12:50 oberon /bsd: wsmouse0 at ums0 mux 0 > May 4 00:12:50 oberon /bsd: uhub2 at uhub1 port 4 > May 4 00:12:50 oberon /bsd: uhub2: ALCOR macally Kbd Hub, rev 1.10/1.00, > addr 4 > May 4 00:12:50 oberon /bsd: uhub2: 3 ports with 2 removable, bus powered > May 4 00:12:50 oberon /bsd: uhidev1 at uhub2 port 1 configuration 1 > interface 0 > May 4 00:12:50 oberon /bsd: uhidev1: ALCOR macally Kbd Hub, rev 1.10/1.00, > addr 5, iclass 3/1 > May 4 00:12:50 oberon /bsd: ukbd0 at uhidev1: 8 modifier keys, 6 key codes, > country code 1 > May 4 00:12:50 oberon /bsd: wskbd1 at ukbd0 mux 1 > May 4 00:12:50 oberon /bsd: wskbd1: connecting to wsdisplay0 > May 4 00:12:50 oberon /bsd: uhub3 at uhub1 port 5 > May 4 00:12:50 oberon /bsd: uhub3: Atmel UHB124 hub, rev 1.10/3.00, addr 6 > May 4 00:12:50 oberon /bsd: uhub3: 4 ports with 4 removable, self powered > May 4 00:12:50 oberon /bsd: uscanner0 at uhub1 port 6 > May 4 00:12:50 oberon /bsd: uscanner0: EPSON EPSON Scanner, rev 1.10/1.00, > addr 7 > May 4 00:12:50 oberon /bsd: dkcsum: wd0 matches BIOS drive 0x80 > May 4 00:12:50 oberon /bsd: dkcsum: wd1 matches BIOS drive 0x81 > May 4 00:12:50 oberon /bsd: root on wd0a > May 4 00:12:50 oberon /bsd: rootdev=0x0 rrootdev=0x300 rawdev=0x302 > May 4 00:12:50 oberon savecore: no core dump > May 4 00:12:51 oberon routed[32060]: pppoe0 has a bad address > May 4 00:12:51 oberon routed[32060]: static route --> 0.0.0.0 impossibly > lacks ifp > May 4 00:12:51 oberon ripd[27299]: WARNING: IP forwarding NOT enabled > May 4 00:12:51 oberon ospfd[14178]: WARNING: IP forwarding NOT enabled, > running as stub router > May 4 00:12:51 oberon bgpd[9988]: setup_listeners setsockopt TTL: Invalid > argument > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.2.1.1: session_connect bind: > Can't assign requested address > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.0.2.0 (upstream2): > session_connect bind: Can't assign requested address > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.2.0.2 (peering AS 65042): > session_connect bind: Can't assign requested address > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.2.0.1 (peering AS 65042): > session_connect bind: Can't assign requested address > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.1.0.3 (AS 65001 peer 2): > session_connect bind: Can't assign requested address > May 4 00:12:51 oberon bgpd[9988]: neighbor 10.1.0.2 (AS 65001 peer 1): > connect: Can't assign requested address > May 4 00:12:52 oberon inetd[13749]: telnet1/tcp: unknown service > May 4 00:12:53 oberon postfix/postfix-script: warning: > /var/spool/postfix/etc/services and /etc/services differ > May 4 00:12:53 oberon bgpd[29013]: change req for ff02:5::/32: not in table > May 4 00:12:53 oberon /bsd: pppoe: alien host unique tag, no session found > May 4 00:12:53 oberon /bsd: pppoe: received PADO but could not find request > for it > > -- > Here my ticker tape .signature #### My name is Peter Philipp #### lynx -dump > "http://en.wikipedia.org/w/index.php?title=Pufferfish&oldid=20768394"; | sed > -n 131,137p #### http://centroid.eu #### So long and thanks for all the > fish!!! > -- Here my ticker tape .signature #### My name is Peter Philipp #### lynx -dump "http://en.wikipedia.org/w/index.php?title=Pufferfish&oldid=20768394"; | sed -n 131,137p #### http://centroid.eu #### So long and thanks for all the fish!!!
