Hi, I got a weird behavior with my net4801 and vpn1411 card when using OpenBSD. Tried this with 4.0, 4.0-current and now 4.1-stable.
With the GENERIC kernel I get "Corrupted MAC on input" after a short time during an SSH connection. Since I had to modify the kernel options slighty to get my APC UPS working with OpenBSD 4.0 over USB so I build myself a custom SOEKRIS kernel. This also got me rid of the "Corrupted MAC on input" issue. Since a custom kernel is not needed anymore for the APC UPS with OpenBSD 4.1 because the USV gets properly detected as ugen0 I just kept the GENERIC kernel. But now I have "Corrupted MAC on input" again. After compiling a custom SOEKRIS kernel for 4.1 too the corrupted MAC issue is gone again. List of needed config changes taken from: http://www.apcupsd.com/manual/USB_Configuration.html#SECTION000102300000000000000 Please have a look at the diff between the GENERIC and my custom SOEKRIS config below and also both dmesg outputs. I also made a diff of both dmesg outputs for easy comparison. Would be nice if someone got an idea about why that fixes the "Corrupted MAC on input" issue. Michael --- sys/arch/i386/conf/GENERIC Wed Feb 28 22:54:43 2007 +++ sys/arch/i386/conf/SOEKRIS Thu May 3 19:51:06 2007 @@ -218,14 +218,14 @@ umass* at uhub? # USB Mass Storage devices scsibus* at umass? atapiscsi* at umass? -uhidev* at uhub? # Human Interface Devices -ums* at uhidev? # USB mouse -wsmouse* at ums? mux 0 -ukbd* at uhidev? # USB keyboard -wskbd* at ukbd? mux 1 -ucycom* at uhidev? # Cypress serial -ucom* at ucycom? -uhid* at uhidev? # USB generic HID support +#uhidev* at uhub? # Human Interface Devices +#ums* at uhidev? # USB mouse +#wsmouse* at ums? mux 0 +#ukbd* at uhidev? # USB keyboard +#wskbd* at ukbd? mux 1 +#ucycom* at uhidev? # Cypress serial +#ucom* at ucycom? +#uhid* at uhidev? # USB generic HID support aue* at uhub? # ADMtek AN986 Pegasus Ethernet atu* at uhub? # Atmel AT76c50x based 802.11b axe* at uhub? # ASIX Electronics AX88172 USB Ethernet OpenBSD 4.1 (GENERIC) #0: Wed May 2 15:56:17 CEST 2007 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC" 586-class) 267 MHz cpu0: FPU,TSC,MSR,CX8,CMOV,MMX cpu0: TSC disabled real mem = 268005376 (261724K) avail mem = 236859392 (231308K) using 3302 buffers containing 13524992 bytes (13208K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+ BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840 pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 pcibios0: pcibios_get_intr_routing - function not supported pcibios0: PCI IRQ Routing information unavailable. pcibios0: PCI bus #1 is the last bus bios0: ROM list: 0xc8000/0x9000 cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00 sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:64 nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:65 nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:66 nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1 ppb0 at pci0 dev 10 function 0 "TI PCI2250 PCI-PCI" rev 0x02 pci1 at ppb0 bus 1 sis3 at pci1 dev 0 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 9, address 00:00:24:c7:4c:2c nsphyter3 at sis3 phy 0: DP83815 10/100 PHY, rev. 1 sis4 at pci1 dev 1 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, address 00:00:24:c7:4c:2d nsphyter4 at sis4 phy 0: DP83815 10/100 PHY, rev. 1 sis5 at pci1 dev 2 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 9, address 00:00:24:c7:4c:2e nsphyter5 at sis5 phy 0: DP83815 10/100 PHY, rev. 1 sis6 at pci1 dev 3 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, address 00:00:24:c7:4c:2f nsphyter6 at sis6 phy 0: DP83815 10/100 PHY, rev. 1 hifn0 at pci0 dev 14 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4 MD5 SHA1 RNG AES PK, 32KB dram, irq 11 gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00 gpio0 at gscpcib0: 64 pins "NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: <CF300> wd0: 1-sector PIO, LBA, 983MB, 2014992 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6 revision 3 wdstatus 0 ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5, version 1.0, legacy support usb0 at ohci0: USB revision 1.0 uhub0 at usb0 uhub0: Compaq OHCI root hub, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered isa0 at gscpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS gpio1 at nsclpcsio0: 29 pins gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1: npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom0: console pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo biomask f1e5 netmask ffe5 ttymask ffe7 pctr: no performance counters in CPU ugen0 at uhub0 port 1 ugen0: American Power Conversion Back-UPS CS 500 FW:808.q5.I USB FW:q5, rev 1.10/0.06, addr 2 dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 OpenBSD 4.1 (SOEKRIS) #0: Thu May 3 19:59:26 CEST 2007 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/SOEKRIS cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC" 586-class) 267 MHz cpu0: FPU,TSC,MSR,CX8,CMOV,MMX cpu0: TSC disabled real mem = 268005376 (261724K) avail mem = 236883968 (231332K) using 3302 buffers containing 13524992 bytes (13208K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+ BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840 pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 pcibios0: pcibios_get_intr_routing - function not supported pcibios0: PCI IRQ Routing information unavailable. pcibios0: PCI bus #1 is the last bus bios0: ROM list: 0xc8000/0x9000 cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00 sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:64 nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:65 nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10, address 00:00:24:c7:7f:66 nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1 ppb0 at pci0 dev 10 function 0 "TI PCI2250 PCI-PCI" rev 0x02 pci1 at ppb0 bus 1 sis3 at pci1 dev 0 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 9, address 00:00:24:c7:4c:2c nsphyter3 at sis3 phy 0: DP83815 10/100 PHY, rev. 1 sis4 at pci1 dev 1 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, address 00:00:24:c7:4c:2d nsphyter4 at sis4 phy 0: DP83815 10/100 PHY, rev. 1 sis5 at pci1 dev 2 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 9, address 00:00:24:c7:4c:2e nsphyter5 at sis5 phy 0: DP83815 10/100 PHY, rev. 1 sis6 at pci1 dev 3 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, address 00:00:24:c7:4c:2f nsphyter6 at sis6 phy 0: DP83815 10/100 PHY, rev. 1 hifn0 at pci0 dev 14 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4 MD5 SHA1 RNG AES PK, 32KB dram, irq 11 gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00 gpio0 at gscpcib0: 64 pins "NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: <CF300> wd0: 1-sector PIO, LBA, 983MB, 2014992 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6 revision 3 wdstatus 0 ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5, version 1.0, legacy support usb0 at ohci0: USB revision 1.0 uhub0 at usb0 uhub0: Compaq OHCI root hub, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered isa0 at gscpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS gpio1 at nsclpcsio0: 29 pins gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1: npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom0: console pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo biomask f1e5 netmask ffe5 ttymask ffe7 pctr: no performance counters in CPU ugen0 at uhub0 port 1 ugen0: American Power Conversion Back-UPS CS 500 FW:808.q5.I USB FW:q5, rev 1.10/0.06, addr 2 dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 soekris:~/home # diff -u dmesg.generic dmesg.soekris --- dmesg.generic Fri May 4 09:42:18 2007 +++ dmesg.soekris Fri May 4 09:42:22 2007 @@ -1,10 +1,10 @@ -OpenBSD 4.1 (GENERIC) #0: Wed May 2 15:56:17 CEST 2007 - [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC +OpenBSD 4.1 (SOEKRIS) #0: Thu May 3 19:59:26 CEST 2007 + [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/SOEKRIS cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC" 586-class) 267 MHz cpu0: FPU,TSC,MSR,CX8,CMOV,MMX cpu0: TSC disabled real mem = 268005376 (261724K) -avail mem = 236859392 (231308K) +avail mem = 236883968 (231332K) using 3302 buffers containing 13524992 bytes (13208K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+ BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840
