Hi
i'm currently tring to add an external disk (thecus n2050 in raid1;
fat32+ffs partitions) to my openbsd (4.0-stable/i386) box on usb2
problem
* partitionning on openbsd works on openbsd, but seems not recognized by
macosx (10.3) and win (2k)
* partitionning and formating on osx is not recognized by openbsd :(
i also fail to repartition on openbsd after osx partitionning:
after creating partition,
fdisk:*1> quit
Writing current MBR to disk.
fdisk: error writing MBR: Input/output error
fdisk:*1>
=> can't quit fdisk, only ^C
(and nothing is written, even with 'w' only)
$ sudo fdisk -i sd1
fdisk: sysctl(machdep.bios.diskinfo): Device not configured
-----------------------------------------------------
------ ATTENTION - UPDATING MASTER BOOT RECORD ------
-----------------------------------------------------
Do you wish to write new MBR and partition table? [n] y
fdisk: error initializing MBR: Input/output error
during these two steps, i get this in dmesg:
sd1(umass0:1:1): Check Condition (error 0x70) on opcode 0x2a
SENSE KEY: Aborted Command
ASC/ASCQ: No Additional Sense Information
sd1(umass0:1:1): Check Condition (error 0x70) on opcode 0x2a
SENSE KEY: Aborted Command
ASC/ASCQ: No Additional Sense Information
=> problem with new disk ? or with n2050 ?
dmesg joined
thanks a lot
Regards
Julien
OpenBSD 4.0-stable (GENERIC) #2: Fri Mar 16 20:51:07 CET 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 351 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 435761152 (425548K)
avail mem = 389361664 (380236K)
using 4256 buffers containing 21889024 bytes (21376K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(06) BIOS, date 03/03/00, BIOS32 rev. 0 @ 0xf0520
apm0 at bios0: Power Management spec V1.2 (BIOS mgmt disabled)
apm0: APM power management enable: unrecognized device ID (9)
apm0: APM engage (device 1): power management disabled (1)
apm0: AC on, battery charge unknown
apm0: flags b0102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xd92
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf0d10/128 (6 entries)
pcibios0: PCI Interrupt Router at 000:04:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x800 0xcc000/0x1800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6326 VGA" rev 0x0b: aperture at 0xe3800000,
size 0x400000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 4 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 4 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALL EX6.4A>
wd0: 16-sector PIO, LBA, 6149MB, 12594960 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 4 function 2 "Intel 82371AB USB" rev 0x01: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 4 function 3 "Intel 82371AB Power" rev 0x02: SMI
iic0 at piixpm0
"unknown" at iic0 addr 0x18 not configured
lm1 at iic0 addr 0x2d: W83781D
emu0 at pci0 dev 9 function 0 "Creative Labs SoundBlaster Live" rev 0x07: irq 5
ac97: codec id 0x83847608 (SigmaTel STAC9708/11)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at emu0
"Creative Labs PCI Gameport Joystick" rev 0x07 at pci0 dev 9 function 1 not
configured
xl0 at pci0 dev 10 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 12,
address 00:04:76:24:cd:fa
exphy0 at xl0 phy 24: 3Com internal media interface
uhci1 at pci0 dev 11 function 0 "VIA VT83C572 USB" rev 0x61: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 11 function 1 "VIA VT83C572 USB" rev 0x61: irq 12
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 11 function 2 "VIA VT6202 USB" rev 0x63: irq 5
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: VIA EHCI root hub, rev 2.00/1.00, addr 1
uhub3: 4 ports with 4 removable, self powered
"VIA VT6306 FireWire" rev 0x46 at pci0 dev 11 function 3 not configured
pciide1 at pci0 dev 12 function 0 "Promise PDC20262" rev 0x01: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide1: using irq 11 for native-PCI interrupt
wd1 at pciide1 channel 0 drive 0: <ST3120026A>
wd1: 16-sector PIO, LBA48, 114473MB, 234441648 sectors
wd1(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 4
wd2 at pciide1 channel 1 drive 1: <WDC WD800BB-00CAA0>
wd2: 16-sector PIO, LBA, 76319MB, 156301488 sectors
wd2(pciide1:1:1): using PIO mode 4, Ultra-DMA mode 4
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83781D
lm1 detached
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ff65 netmask ff65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
uhub0: device problem, disabling port 2
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
dkcsum: wd2 matches BIOS drive 0x82
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
uhub0: device problem, disabling port 2
uhub0: device problem, disabling port 2
wd1d: aborted command, interface CRC error reading fsbn 38683392 of
38683392-38683423 (wd1 bn 80626272; cn 79986 tn 6 sn 6), retrying
wd1: transfer error, downgrading to Ultra-DMA mode 3
wd1(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 3
wd1d: aborted command, interface CRC error reading fsbn 38683392 of
38683392-38683423 (wd1 bn 80626272; cn 79986 tn 6 sn 6), retrying
wd1: soft error (corrected)
umass0 at uhub3 port 4 configuration 1 interface 0
umass0: Sunplus Technology Inc. USB to Serial-ATA bridge, rev 2.00/c6.83, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets
sd0 at scsibus0 targ 1 lun 0: <External, Disk 0, > SCSI2 0/direct fixed
sd0: 305245MB, 305245 cyl, 64 head, 32 sec, 512 bytes/sec, 625142448 sec total
sd1 at scsibus0 targ 1 lun 1: <Config, Disk, > SCSI2 0/direct fixed
sd1: 0MB, 0 cyl, 64 head, 32 sec, 512 bytes/sec, 640 sec total
