Hi,
I'm running OpenBSD 3.9-stable on a Lenovo (formerly IBM) Thinkpad T43p.
X (X.org 6.9.0) works fine either
(a) without any /etc/X11/xorg.conf, or
(b) using the /etc/X11/xorg.conf from http://www.enting.se/T43/xorg.conf
(which is linked from the T43 entry in
http://www.openbsd.org/i386-laptop.html).
All the behavior I describe below is identical for (a) and (b).
The built-in LCD display works fine at 1600x1200.
My problem is that I can't get external video output properly. There
seem to be two cases (neither one of which fits my definition of
"properly"): * If, in the BIOS setup, I set "Boot Display Device" to
"LCD", then I can get 1600x1200 VGA output when booting and before I
start X, but I get no external video output at all once I start X.
* If, in the BIOS setup, I set "Boot Display Device" to "VGA+LCD" or
"VGA+DVI+LCD", then I get no external video output when booting and
before I start X, but when I start X I get only 640x480 resolution
(and matching external video output).
Does anyone know how to get a T43p to simultaneously
* run X,
* use a decent screen resolution (minimum 1024x768, prefer 1280x1024
and/or 1600x1200)
* send this video to the external VGA connector so I can display things
on a video projector
Here are my dmesg and the /etc/X11/xorg.conf from (b) above:
=== begin dmesg ===
OpenBSD 3.9-stable (GENERIC) #9: Tue Jan 9 16:30:11 CET 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 2.13GHz ("GenuineIntel"
686-class) 2.13 GHz cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUS
H,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2 cpu0: Enhanced SpeedStep
1600 MHz (1356 mV): speeds: 2130, 1800, 1600, 1400, 1200, 1000, 800,
600 MHz real mem = 2145886208 (2095592K)
avail mem = 1951961088 (1906212K)
using 4278 buffers containing 107397120 bytes (104880K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(8d) BIOS, date 09/15/05, BIOS32 rev. 0 @
0xfd760 apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 97%
apm0: AC on, battery charge high
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd6f0/0x910
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdeb0/256 (14 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev
0x00) pcibios0: PCI bus #5 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1600 0xd1800/0x1000
0xdc000/0x4000! 0xe0000/0x10000 cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI FireGL V3200" rev 0x80
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03
pci2 at ppb1 bus 2
bge0 at pci2 dev 0 function 0 "Broadcom BCM5751M" rev 0x11, BCM5750 B1
(0x4101): irq 11, address 00:01:6c:e9:50:d0 brgphy0 at bge0 phy 1:
BCM5750 10/100/1000baseT PHY, rev. 0
ppb2 at pci0 dev 28 function 2 "Intel 82801FB PCIE" rev 0x03
pci3 at ppb2 bus 3
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: irq 11
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: irq 11
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3
pci4 at ppb3 bus 4
cbb0 at pci4 dev 0 function 0 "Ricoh 5C476 CardBus" rev 0x8d: irq 11
ath0 at pci4 dev 2 function 0 "Atheros AR5212 (IBM MiniPCI)" rev 0x01:
irq 11 ath0: AR5213 5.9 phy 4.3 rf5112 3.6, WOR2W, address
00:14:a4:5c:7f:a5 cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 5 device 0 cacheline 0x0, lattimer 0xb0
pcmcia0 at cardslot0
auich0 at pci0 dev 30 function 2 "Intel 82801FB AC97" rev 0x03: irq 11,
ICH6 AC97 ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801FB Modem" rev 0x03 at pci0 dev 30 function 3 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03: PM
disabled pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev
0x03: DMA, channel 0 wired to compatibility, channel 1 wired to
compatibility wd0 at pciide0 channel 0 drive 0: <HTS721010G9AT00>
wd0: 16-sector PIO, LBA, 95396MB, 195371568 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, DVD-RAM UJ-822S, 1.61> SCSI0
5/cdrom removable cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x03: irq 11
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
aps0 at isa0 port 0x1600/31
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask efed netmask efed ttymask ffef
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
=== end dmesg ===
=== begin /etc/X11/xorg.conf ===
# $Id: xorg.conf,v 1.1 2006/02/10 12:37:54 root Exp root $
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/TTF/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/CID/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/local/lib/X11/fonts/mscorefonts"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "glx"
Load "record"
Load "xtrap"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "thinkpad"
## Option "XkbLayout" "se"
## Option "XkbOptions" "ctrl:ctrl_aa,eurosign:5"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "wsmouse"
Option "Device" "/dev/wsmouse"
## Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "Dac6Bit" # [<bool>]
#Option "Dac8Bit" # [<bool>]
#Option "PanelOff" # [<bool>]
#Option "DDCMode" # [<bool>]
#Option "MonitorLayout" # [<str>]
#Option "IgnoreEDID" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "MergedFB" # [<bool>]
#Option "CRT2HSync" # [<str>]
#Option "CRT2VRefresh" # [<str>]
#Option "CRT2Position" # [<str>]
#Option "MetaModes" # [<str>]
#Option "MergedDPI" # [<str>]
#Option "MergedXinerama" # [<bool>]
#Option "MergedXineramaCRT2IsScreen0" # [<bool>]
#Option "MergedNonRectangular" # [<bool>]
#Option "MergedMouseRestriction" # [<bool>]
#Option "DisplayPriority" # [<str>]
#Option "PanelSize" # [<str>]
#Option "ForceMinDotClock" # <freq>
#Option "ColorTiling" # [<bool>]
#Option "VideoKey" # <i>
#Option "RageTheatreCrystal" # <i>
#Option "RageTheatreTunerPort" # <i>
#Option "RageTheatreCompositePort" # <i>
#Option "RageTheatreSVideoPort" # <i>
#Option "TunerType" # <i>
#Option "RageTheatreMicrocPath" # <str>
#Option "RageTheatreMicrocType" # <str>
#Option "RenderAccel" # [<bool>]
#Option "SubPixelOrder" # [<str>]
#Option "ShowCache" # [<bool>]
#Option "DynamicClocks" # [<bool>]
#Option "BIOSHotkeys" # [<bool>]
#Option "VGAAccess" # [<bool>]
#Option "ReverseDDC" # [<bool>]
#Option "LVDSProbePLL" # [<bool>]
#Option "AccelMethod" # <str>
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "M22 [Radeon Mobility M300]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Group 0
EndSection
# $Log: xorg.conf,v $
# Revision 1.1 2006/02/10 12:37:54 root
# Initial revision
#
=== end /etc/X11/xorg.conf ===
ciao,
--
-- "Jonathan Thornburg -- remove -animal to reply"
<[EMAIL PROTECTED]> Max-Planck-Institut fuer
Gravitationsphysik (Albert-Einstein-Institut), Golm, Germany, "Old
Europe" http://www.aei.mpg.de/~jthorn/home.html "Washing
one's hands of the conflict between the powerful and the powerless
means to side with the powerful, not to be neutral."
-- quote by Freire / poster by Oxfam
