Hi,
I'm running an OpenBSD/i386 recent snapshot on a few 'HP DL360 G4p's,
all seems good apart from the first NIC (bge0) will not see the LAN.
An 'ifconfig bge0' output cycles between "media: Ethernet autoselect
(none)" and "media: Ethernet autoselect (loopback)", with "status: no
carrier" and will not connect to the LAN.
However if I relocate the cable to bge1 then it connects perfectly
and 'ifconfig bge1' shows "media: Ethernet autoselect (1000baseT full-
duplex)" and "status: active".
I've tried 5 identical machines, with different switch ports and
cables, and behaviour is consistent: bge0 always fails, and bge1
always works. I've also tried moving the NICs from IRQ 7 to IRQ5,
(they are forced to use same IRQ) in the BIOS without effect. Thus
I'm pretty sure the problem is not switch, cabling or server
hardware. Adding the debug flag on bge0 reveals nothing in logs.
In the short term I can run on just bge1, but I'm hoping to do NIC/
switch redundancy via trunk(4) so I'll need bge0. Any suggestions
greatly recieved.
Full dmesg below.
thanks,
/Pete
[EMAIL PROTECTED] ~>cat /var/run/dmesg.boot
OpenBSD 4.0-current (GENERIC) #1134: Mon Oct 2 19:44:53 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Xeon(TM) CPU 3.40GHz ("GenuineIntel" 686-class) 3.41 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-
CPL,EST,CNXT-ID,CX16
cpu0: EST: strange msr value 0x0000112d0000112d
real mem = 2147000320 (2096680K)
avail mem = 1950441472 (1904728K)
using 4256 buffers containing 107454464 bytes (104936K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @
0xf0000, SMBIOS rev. 2.3 @ 0xec000 (73 entries)
bios0: HP ProLiant DL360 G4p
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 7 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 6300ESB LPC" rev
0x00)
pcibios0: PCI bus #13 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000! 0xee000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel E7520 MCH" rev 0x0c
ppb0 at pci0 dev 2 function 0 "Intel MCH PCIE" rev 0x0c
pci1 at ppb0 bus 13
ppb1 at pci0 dev 4 function 0 "Intel MCH PCIE" rev 0x0c
pci2 at ppb1 bus 6
ppb2 at pci2 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
pci3 at ppb2 bus 7
ppb3 at pci2 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09
pci4 at ppb3 bus 10
ppb4 at pci0 dev 6 function 0 "Intel MCH PCIE" rev 0x0c
pci5 at ppb4 bus 3
ppb5 at pci0 dev 28 function 0 "Intel 6300ESB PCIX" rev 0x02
pci6 at ppb5 bus 2
ciss0 at pci6 dev 1 function 0 "Compaq Smart Array 64xx" rev 0x01: irq 7
ciss0: 1 LD, HW rev 1, FW 2.68/2.68
scsibus0 at ciss0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <HP, LOGICAL VOLUME, 2.68> SCSI0 0/
direct fixed
sd0: 140006MB, 140006 cyl, 64 head, 32 sec, 512 bytes/sec, 286734240
sec total
bge0 at pci6 dev 2 function 0 "Broadcom BCM5704C" rev 0x10, BCM5704
B0 (0x2100): irq 7, address 00:18:fe:32:1e:08
brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge1 at pci6 dev 2 function 1 "Broadcom BCM5704C" rev 0x10, BCM5704
B0 (0x2100): irq 7, address 00:18:fe:32:1e:07
brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 6300ESB USB" rev 0x02: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 6300ESB USB" rev 0x02: irq 5
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
"Intel 6300ESB WDT" rev 0x02 at pci0 dev 29 function 4 not configured
"Intel 6300ESB APIC" rev 0x02 at pci0 dev 29 function 5 not configured
ehci0 at pci0 dev 29 function 7 "Intel 6300ESB USB" rev 0x02: irq 7
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x0a
pci7 at ppb6 bus 1
vga1 at pci7 dev 3 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Compaq iLO" rev 0x01 at pci7 dev 4 function 0 not configured
"Compaq iLO" rev 0x01 at pci7 dev 4 function 2 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 6300ESB LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 6300ESB IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, CD-ROM GCR-8240N, 2.03>
SCSI0 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 disabled (no drives)
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask efe5 netmask efe5 ttymask ffe7
pctr: user-level cycle counter enabled
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
[EMAIL PROTECTED] ~>ifconfig bge0
bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:18:fe:32:1e:08
media: Ethernet autoselect (none)
status: no carrier
[EMAIL PROTECTED] ~>ifconfig bge1
bge1: flags=8847<UP,BROADCAST,DEBUG,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:18:fe:32:1e:07
groups: egress
media: Ethernet autoselect (1000baseT full-duplex)
status: active
inet 11.22.33.44 netmask 0xffffff00 broadcast 11.22.33.255
