Hi,
I am having some issues getting a trunk consisting of bge0 and iwi0
working on the iwi0 side.
This is what I have after booting without creating the trunk.
teletron1:/home/dangt$ cat /etc/hostname.bge0
up
teletron1:/home/dangt$ cat /etc/hostname.iwi0
up nwid Predacon nwkey 0xXXXX
teletron1:/home/dangt$ cat /etc/hostname.trunk0
#dhcp NONE NONE NONE trunkproto failover trunkport bge0 trunkport iwi0
teletron1:/home/dangt$ ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:12:3f:e2:e4:c4
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::212:3fff:fee2:e4c4%bge0 prefixlen 64 scopeid 0x1
iwi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:13:ce:44:8a:ad
media: IEEE802.11 autoselect
status: active
ieee80211: nwid Predacon chan 6 bssid 00:13:10:6b:b2:1d 95dB
nwkey <not displayed> 100dBm
inet6 fe80::213:ceff:fe44:8aad%iwi0 prefixlen 64 scopeid 0x2
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33224
pfsync0: flags=0<> mtu 1460
groups: carp
enc0: flags=0<> mtu 1536
trunk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:00:00:00:00:00
trunk: trunkproto roundrobin
groups: trunk
media: Ethernet autoselect
status: no carrier
The iwi0 status is active but when I create the trunk, iwi0 will go
down. The system will hang while trying to create the trunk.
teletron1:/home/dangt$ sudo ifconfig trunk0 trunkproto failover
trunkport bge0 trunkport iwi0
We trust you have received the usual lecture from the local System
Administrator. It usually boils down to these three things:
#1) Respect the privacy of others.
#2) Think before you type.
#3) With great power comes great responsibility.
Password:
ifconfig: SIOCSTRUNKPORT: Network is down
teletron1:/home/dangt$ sudo dhclient trunk0
DHCPREQUEST on trunk0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.226 -- renewal in 21600 seconds.
teletron1:/home/dangt$ ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:12:3f:e2:e4:c4
trunk: trunkdev trunk0
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::212:3fff:fee2:e4c4%bge0 prefixlen 64 scopeid 0x1
iwi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:13:ce:44:8a:ad
media: IEEE802.11 autoselect
status: no network
ieee80211: nwid Predacon nwkey <not displayed> 100dBm
inet6 fe80::213:ceff:fe44:8aad%iwi0 prefixlen 64 scopeid 0x2
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33224
pfsync0: flags=0<> mtu 1460
groups: carp
enc0: flags=0<> mtu 1536
trunk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:12:3f:e2:e4:c4
trunk: trunkproto failover
trunkport bge0 master,active
groups: trunk egress
media: Ethernet autoselect
status: active
inet6 fe80::212:3fff:fee2:e4c4%trunk0 prefixlen 64 scopeid 0x7
inet 192.168.1.226 netmask 0xffffff00 broadcast 192.168.1.255
I get a
iwi0: fatal firmware error
in the dmesg after creating the trunk. I guess this is my problem.
Is it just not possible to setup a trunk with an iwi device?
Tan
OpenBSD 4.0 (GENERIC) #1104: Fri Sep 1 11:54:27 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 2.26GHz ("GenuineIntel"
686-class) 2.27 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE
2,SS,TM,SBF,EST,TM2
cpu0: unknown Enhanced SpeedStep CPU, msr 0x0612112b0600112b
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 2267 MHz (1388 mV): speeds: 2267, 800 MHz
real mem = 2146889728 (2096572K)
avail mem = 1950318592 (1904608K)
using 4256 buffers containing 107446272 bytes (104928K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 07/04/05, BIOS32 rev. 0 @
0xffe90, SMBIOS rev. 2.3 @ 0xf7910
(60 entries)
bios0: Dell Inc. Latitude D810
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfb2d0/176 (9 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371 ISA and IDE" rev 0x00)
pcibios0: PCI bus #4 is the last bus
bios0: ROM list: 0xc0000/0x10000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility X600" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03
pci2 at ppb1 bus 2
bge0 at pci2 dev 0 function 0 "Broadcom BCM5751" rev 0x01, BCM5750 A1
(0x4001): irq 11, address 00:12:3
f:e2:e4:c4
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: irq 5
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: irq 11
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3
pci3 at ppb2 bus 3
cbb0 at pci3 dev 1 function 0 "TI PCI6515 CardBus" rev 0x00: irq 5
"TI PCI6515 CardBus (Smart Card mode)" rev 0x00 at pci3 dev 1 function
5 not configured
iwi0 at pci3 dev 3 function 0 "Intel PRO/Wireless 2915ABG" rev 0x05:
irq 10, address 00:13:ce:44:8a:ad
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 4 device 0 cacheline 0x10, lattimer 0x20
pcmcia0 at cardslot0
auich0 at pci0 dev 30 function 2 "Intel 82801FB AC97" rev 0x03: irq
11, ICH6 AC97
ac97: codec id 0x83847650 (SigmaTel STAC9750/51)
ac97: codec features headphone, 20 bit DAC, 20 bit ADC, SigmaTel 3D
audio0 at auich0
"Intel 82801FB Modem" rev 0x03 at pci0 dev 30 function 3 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03: PM disabled
pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x03: DMA,
channel 0 wired to compatibility
, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Hitachi HTS721080G9AT00>
wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <_NEC, DVD+-RW ND-6650A, 102C> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x03: SMI
iic0 at ichiic0
"unknown" at iic0 addr 0x18 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask efed netmask efed ttymask ffef
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
ugen0 at uhub1 port 1
ugen0: Dell Bluetooth 350, rev 2.00/16.57, addr 2
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
iwi0: fatal firmware error
