Hi,
I'm trying to install OpenBSD 3.9 -release onto a HP ProLiant DL360 G4
server. I get a "no disk found" message after the <Proceed with
install?> question.
The system has an Intel 6300ESB/82801FR SATA Controller and is running a
single Maxtor SATA HDD. I think if I could set the controller to
"compatibility" instead of "native-pci" it would work, unfortunately I'm
not sure how to go about doing this as there are no BIOS options in
relation to the controller.
Full dmesg is below.
-----
OpenBSD 3.9 (RAMDISK_CD) #1025: Thu Mar 2 02:43:29 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Xeon(TM) CPU 3.00GHz ("GenuineIntel" 686-class) 3 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
real mem = 1073270784 (1048116K)
avail mem = 973778944 (950956K)
using 4278 buffers containing 53768192 bytes (52508K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 7 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 6300ESB LPC" rev 0x00)
pcibios0: PCI bus #7 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x3600! 0xcb600/0x1600
0xee000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel E7520 MCH" rev 0x0a
ppb0 at pci0 dev 2 function 0 "Intel MCH PCIE" rev 0x0a
pci1 at ppb0 bus 1
ppb1 at pci0 dev 4 function 0 "Intel MCH PCIE" rev 0x0a
pci2 at ppb1 bus 2
ppb2 at pci2 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
pci3 at ppb2 bus 3
ppb3 at pci2 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09
pci4 at ppb3 bus 4
ppb4 at pci0 dev 6 function 0 "Intel MCH PCIE" rev 0x0a
pci5 at ppb4 bus 5
ppb5 at pci0 dev 28 function 0 "Intel 6300ESB PCIX" rev 0x02
pci6 at ppb5 bus 6
bge0 at pci6 dev 2 function 0 "Broadcom BCM5704C" rev 0x10, BCM5704 B0
(0x2100): irq 5, address 00:11:85:c2:d0:bb
brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge1 at pci6 dev 2 function 1 "Broadcom BCM5704C" rev 0x10, BCM5704 B0
(0x2100): irq 5, address 00:11:85:c2:d0:ba
brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 6300ESB USB" rev 0x02: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 5300ESB USB" rev 0x02: irq 5
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
"Intel 6300ESB WDT" rev 0x02 at pci0 dev 29 function 4 not configured
"Intel 6300ESB APIC" rev 0x02 at pci0 dev 29 function 5 not configured
ehci0 at pci0 dev 29 function 7 "Intel 6300ESB USB" rev 0x02: irq 5
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x0a
pci7 at ppb6 bus 7
vga1 at pci7 dev 3 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
"Compaq iLO" rev 0x01 at pci7 dev 4 function 0 not configured
"Compaq iLO" rev 0x01 at pci7 dev 4 function 2 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 6300ESB LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 6300ESB IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-N, C.6B> SCSI0 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 31 function 2 "Intel 6300ESB SATA" rev 0x02: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: couldn't map channel 0 cmd regs
pciide1: couldn't map channel 1 cmd regs
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask ffe5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
uhub3 at uhub2 port 4
uhub3: Prolific Technology Inc. USB_HUB, rev 2.00/0.01, addr 2
uhub3: 1 port with 0 removable, bus powered, single transaction translator
umass0 at uhub3 port 1 configuration 1 interface 0
umass0: Prolific Technology Inc. USB_Storage, rev 2.00/0.01, addr 3
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <Prolific, UsbFlashDisk, PROL> SCSI0
0/direct fixed
sd0: drive offline
root on rd0a
rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
----
Any help is appreciated!
Thanks,
Edward Avent
