Hello dear OpenBSD friends.
I have an Intel 2200 Wireless card on my laptop. It was working on
OpenBSD 3.8. I have just installed a fresh OpenBSD 3.9. I also have
installed the 3.0 firmware.
# pkg_info
iwi-firmware-3.0 Firmware binary image for iwi driver
# ls -l /etc/firmware/iwi*
-rwxr-xr-x 1 root wheel 191142 Mar 26 17:29 /etc/firmware/iwi-bss
-rwxr-xr-x 1 root wheel 185660 Mar 26 17:29 /etc/firmware/iwi-ibss
-rwxr-xr-x 1 root wheel 12007 Mar 26 17:29 /etc/firmware/iwi-license
-rwxr-xr-x 1 root wheel 187836 Mar 26 17:29 /etc/firmware/iwi-monitor
I get his error whe using the command:
#ifconfig -M iwi0
# dmesg | grep iwi
iwi0 at pci1 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq
11, address 00:13:ce:6b:7d:01
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0 at pci1 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq
11, address 00:13:ce:6b:7d:01
iwi0 at pci1 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq
11, address 00:13:ce:6b:7d:01
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
I have tried also 2.3 firmware with the same result. Attached below is
the dmesg.
Thank you very much in advance.
Ramiro.
#dmesg
OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1.86GHz ("GenuineIntel" 686-class)
1.87 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
cpu0: Enhanced SpeedStep 1400 MHz (1356 mV): unknown EST cpu, no changes
possible
real mem = 1064800256 (1039844K)
avail mem = 964870144 (942256K)
using 4278 buffers containing 53342208 bytes (52092K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(e0) BIOS, date 07/12/04, BIOS32 rev. 0 @ 0xea510
pcibios0 at bios0: rev 2.1 @ 0xe6000/0x6b1
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfe840/224 (12 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801AA LPC" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xf400! 0xe0000/0x2000! 0xe5000/0x1000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x04
vga1 at pci0 dev 2 function 0 "Intel 82915GM/GMS Video" rev 0x04:
aperture at 0xd0000000, size 0x10000000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Intel 82915GM/GMS Video" rev 0x04 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: irq 7
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: irq 3
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: irq 11
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: irq 7
ehci0: reset timeout
ehci0: init failed, error=13
ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
pci1 at ppb0 bus 1
"VIA VT6306 FireWire" rev 0x80 at pci1 dev 0 function 0 not configured
re0 at pci1 dev 1 function 0 "Realtek 8169" rev 0x10: irq 11, address
00:0f:b0:93:6f:e1
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
iwi0 at pci1 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq
11, address 00:13:ce:6b:7d:01
cbb0 at pci1 dev 4 function 0 "ENE CB-710 CardBus" rev 0x00pci_intr_map:
no mapping for pin A
: couldn't map interrupt
vendor "ENE", unknown product 0x0530 (class memory subclass flash, rev
0x00) at pci1 dev 4 function 1 not configured
vendor "ENE", unknown product 0x0550 (class system unknown subclass
0x05, rev 0x00) at pci1 dev 4 function 2 not configured
auich0 at pci0 dev 30 function 2 "Intel 82801FB AC97" rev 0x04: irq 5,
ICH6 AC97
ac97: codec id 0x414c4752 (Avance Logic ALC250A?)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at auich0
"Intel 82801FB Modem" rev 0x04 at pci0 dev 30 function 3 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM
disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <IC25N080ATMR04-0>
wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CD/DVDW TS-L632B, TI33> SCSI0
5/cdrom removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04: irq 3
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/65536
pcic0 controller 0: <Intel 82365SL rev 2> has socket A only
pcmcia0 at pcic0 controller 0 socket 0
pcic0: irq 4, polling enabled
biomask efcd netmask efcd ttymask ffdf
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
uhidev0 at uhub2 port 1 configuration 1 interface 0
uhidev0: Alcor Micro product 0x3004, rev 1.10/1.00, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
uhidev1 at uhub0 port 1 configuration 1 interface 0
uhidev1: Genius NetScroll+Mini Traveler, rev 1.10/1.07, addr 2, iclass 3/1
ums0 at uhidev1: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev2 at uhub2 port 1 configuration 1 interface 1
uhidev2: Alcor Micro product 0x3004, rev 1.10/1.00, addr 2, iclass 3/0
uhidev2: 4 report ids
uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
uhid2 at uhidev2 reportid 4: input=1, output=0, feature=0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
iwi0: could not read firmware iwi-boot, error 2
iwi0: could not load boot firmware
umass0 at uhub3 port 1 configuration 1 interface 0
umass0: vendor 0x0457 USB Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <USB 2.0, Flash Disk, 0.00> SCSI2 0/direct
removable
sd0: 254MB, 254 cyl, 64 head, 32 sec, 512 bytes/sec, 520192 sec total
