After install/upgrade OpenBSD 3.9 at the system startup the operating
system jams with this error: "fxp0: SCB time out".
The error is occured when the system tried to assign the IP at the
network card.
Now I have disabled the network startup.
The dmesg reports:
===================
OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006
[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1.73GHz ("GenuineIntel" 686-class)
1.73 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,T
M,SBF,EST,TM2
cpu0: Enhanced SpeedStep 1300 MHz (1308 mV): unknown EST cpu, no changes
possible
real mem = 535273472 (522728K)
avail mem = 481411072 (470128K)
using 4278 buffers containing 26865664 bytes (26236K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(8c) BIOS, date 01/16/05, BIOS32 rev. 0 @ 0xfd6b0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd6b0/0x950
pcibios0: PCI BIOS has 16 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FBM LPC" rev 0x00)
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xec00! 0xdc000/0x4000! 0xe0000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 vendor "NVIDIA", unknown product 0x0167
rev 0xa1
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Intel 82801FB HD Audio" rev 0x04 at pci0 dev 27 function 0 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: irq 3
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: irq 11
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: irq 5
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
pci2 at ppb1 bus 2
cbb0 at pci2 dev 3 function 0 "Texas Instruments PCI7420 CardBus" rev
0x00pci_intr_map: no mapping for pin A
: couldn't map interrupt
"Texas Instruments PCI7x20 FireWire" rev 0x00 at pci2 dev 3 function 2
not configured
vendor "Texas Instruments", unknown product 0xac8f (class mass storage
subclass miscellaneous, rev 0x00) at pci2 dev 3 function 3 not configured
iwi0 at pci2 dev 4 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq
4, address 00:0e:35:d5:d6:ea
fxp0 at pci2 dev 8 function 0 "Intel 82801FBM LAN" rev 0x04, i82562: irq
7, address 00:01:4a:17:e2:f4
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM
disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23FA-80>
wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MAT****A, UJ-831Da, 1.01> SCSI0 5/cdrom
removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04: irq 10
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
biomask ef6d netmask effd ttymask ffff
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
umass0 at uhub4 port 3 configuration 1 interface 0
umass0: Verbatim Store 'n' Go, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <VBTM, Store 'n' Go, 1.04> SCSI0 0/direct
removable
sd0: 489MB, 489 cyl, 64 head, 32 sec, 512 bytes/sec, 1001472 sec total
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: Logitech USB-PS/2 Optical Mouse, rev 2.00/18.00, addr 2, iclass 3/1
ums0 at uhidev0: 6 buttons and Z dir.
wsmouse1 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
