I ran into this on a Thinkpad T43 with a GMA900 adapter. I simply used the xorg.conf created when installing 3.7 which simply specifies a generic VGA/VESA adapter. As I remember when researching this matter, the GMA900 driver is new and problematic. Given that I run 3.8 too, I don't know if the driver in 3.9 resolves this or not.
Jim -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of d 269330400 Sent: Sunday, April 09, 2006 2:01 PM To: misc@openbsd.org Subject: X11 Issue - Integrated Intel Media Accelerator 900 Graphics (Intel 915GM) I recently installed OpenBSD 3.8 (I haven't received my 3.9 CD in the mail yet), and am having problems getting X to work (among other things). It's a Dell Inspiron 1300 notebook w/ Integrated Intel Media Accelerator 900 Graphics (Intel 915GM). The full dmesg is below. So, quick question. I noticed the following bullet on the OpenBSD 3.9 release page. Could this be my problem? That is, is it referring to the same Intel 915 as my graphics? Clueless, I know - sorry. - Support the Intel i915 AGP I've tried following the instructions in /usr/X11R6/README, using the various X wizards (xorgcfg, xorgconfig, xf86config3), and /etc/sysctl.conf has machdep.allowaperture set to 2 because I answered yes to the X question during the install. I also tried copying over the XF86Config and XF86Config-4 files that were generated by a KNOPPIX live-CD that worked on the same box, but that didn't work either. Thanks. --d OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel(R) Celeron(R) M processor 1.40GHz ("GenuineIntel" 686-class) 1.40 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH ,ACPI ,MMX,FXSR,SSE,SSE2,SS,TM,SBF real mem = 527880192 (515508K) avail mem = 474746880 (463620K) using 4278 buffers containing 26497024 bytes (25876K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(00) BIOS, date 01/24/06, BIOS32 rev. 0 @ 0xffe90 pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfb790/176 (9 entries) pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371 ISA and IDE" rev 0x00) pcibios0: PCI bus #3 is the last bus bios0: ROM list: 0xc0000/0xf800! 0xcf800/0x800 cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 915GM/PM/GMS Host" rev 0x03 vga1 at pci0 dev 2 function 0 "Intel 915GM/GMS Video" rev 0x03: aperture at 0xdff00000, size 0x8000000 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) "Intel 915GM/GMS Video" rev 0x03 at pci0 dev 2 function 1 not configured "Intel 82801FB HD Audio" rev 0x03 at pci0 dev 27 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 3 "Intel 82801FB PCIE" rev 0x03 pci2 at ppb1 bus 2 uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: irq 11 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: irq 10 usb1 at uhci1: USB revision 1.0 uhub1 at usb1 uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: irq 9 usb2 at uhci2: USB revision 1.0 uhub2 at usb2 uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: irq 7 usb3 at uhci3: USB revision 1.0 uhub3 at usb3 uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: irq 11 usb4 at ehci0: USB revision 2.0 uhub4 at usb4 uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3 pci3 at ppb2 bus 3 bce0 at pci3 dev 0 function 0 "Broadcom BCM4401B0" rev 0x02: irq 9, address 00:14:22:97:85:e0 bmtphy0 at bce0 phy 1: BCM4401 10/100baseTX PHY, rev. 0 vendor "Broadcom", unknown product 0x4318 (class network subclass miscellaneous, rev 0x02) at pci3 dev 3 function 0 not configured pcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03 pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x03: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility wd0 at pciide0 channel 0 drive 0: <ST9808211A> wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors atapiscsi0 at pciide0 channel 0 drive 1 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CDRW/DVD GCC4244, B101> SCSI0 5/cdrom removable wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 pciide0: channel 1 ignored (disabled) isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 sysbeep0 at pcppi0 npx0 at isa0 port 0xf0/16: using exception 16 biomask effd netmask effd ttymask ffff pctr: 686-class user-level performance counters enabled mtrr: Pentium Pro MTRR support dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel(R) Celeron(R) M processor 1.40GHz ("GenuineIntel" 686-class) 1.40 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH ,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF real mem = 527880192 (515508K) avail mem = 474746880 (463620K) using 4278 buffers containing 26497024 bytes (25876K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(00) BIOS, date 01/24/06, BIOS32 rev. 0 @ 0xffe90 pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfb790/176 (9 entries) pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371 ISA and IDE" rev 0x00) pcibios0: PCI bus #3 is the last bus bios0: ROM list: 0xc0000/0xf800! 0xcf800/0x800 cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 915GM/PM/GMS Host" rev 0x03 vga1 at pci0 dev 2 function 0 "Intel 915GM/GMS Video" rev 0x03: aperture at 0xdff00000, size 0x8000000 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) "Intel 915GM/GMS Video" rev 0x03 at pci0 dev 2 function 1 not configured "Intel 82801FB HD Audio" rev 0x03 at pci0 dev 27 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 3 "Intel 82801FB PCIE" rev 0x03 pci2 at ppb1 bus 2 uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: irq 11 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: irq 10 usb1 at uhci1: USB revision 1.0 uhub1 at usb1 uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: irq 9 usb2 at uhci2: USB revision 1.0 uhub2 at usb2 uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: irq 7 usb3 at uhci3: USB revision 1.0 uhub3 at usb3 uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: irq 11 usb4 at ehci0: USB revision 2.0 uhub4 at usb4 uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3 pci3 at ppb2 bus 3 bce0 at pci3 dev 0 function 0 "Broadcom BCM4401B0" rev 0x02: irq 9, address 00:14:22:97:85:e0 bmtphy0 at bce0 phy 1: BCM4401 10/100baseTX PHY, rev. 0 vendor "Broadcom", unknown product 0x4318 (class network subclass miscellaneous, rev 0x02) at pci3 dev 3 function 0 not configured pcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03 pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x03: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility wd0 at pciide0 channel 0 drive 0: <ST9808211A> wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors atapiscsi0 at pciide0 channel 0 drive 1 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CDRW/DVD GCC4244, B101> SCSI0 5/cdrom removable wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 pciide0: channel 1 ignored (disabled) isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 sysbeep0 at pcppi0 npx0 at isa0 port 0xf0/16: using exception 16 biomask effd netmask effd ttymask ffff pctr: 686-class user-level performance counters enabled mtrr: Pentium Pro MTRR support dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302
