Oops, original message did not include bboot dmesg from installer:
StarFive # bootefi ${kernel_addr_r} ${fdt_addr_r}
Card did not respond to voltage select! : -110
No EFI system partition
disks: sd0*
>> OpenBSD/riscv64 BOOTRISCV64 1.7
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2119542+1090648+8457360+545408
[194778+136+415440+200459]=0xf5c258
clk u5_dw_i2c_clk_core already disabled
clk u5_dw_i2c_clk_apb already disabled
bootargs:
type 0x2 pa 0x40000000 va 0x40000000 pages 0x4000 attr 0x8
type 0x7 pa 0x44000000 va 0x44000000 pages 0x3f00 attr 0x8
type 0x9 pa 0x47f00000 va 0x47f00000 pages 0xc attr 0x8
type 0x7 pa 0x47f0c000 va 0x47f0c000 pages 0xb66e4 attr 0x8
type 0x2 pa 0xfe5f0000 va 0xfe5f0000 pages 0xa attr 0x8
type 0x4 pa 0xfe5fa000 va 0xfe5fa000 pages 0x1 attr 0x8
type 0x7 pa 0xfe5fb000 va 0xfe5fb000 pages 0x1 attr 0x8
type 0x2 pa 0xfe5fc000 va 0xfe5fc000 pages 0x100 attr 0x8
type 0x1 pa 0xfe6fc000 va 0xfe6fc000 pages 0x25 attr 0x8
type 0x4 pa 0xfe721000 va 0xfe721000 pages 0x5 attr 0x8
type 0x6 pa 0xfe726000 va 0xfe726000 pages 0x1 attr 0x8000000000000008
type 0x4 pa 0xfe727000 va 0xfe727000 pages 0x3 attr 0x8
type 0x6 pa 0xfe72a000 va 0xfe72a000 pages 0x3 attr 0x8000000000000008
type 0x4 pa 0xfe72d000 va 0xfe72d000 pages 0x1 attr 0x8
type 0x6 pa 0xfe72e000 va 0xfe72e000 pages 0x4 attr 0x8000000000000008
type 0x4 pa 0xfe732000 va 0xfe732000 pages 0xb attr 0x8
type 0x2 pa 0xfe73d000 va 0xfe73d000 pages 0x1811 attr 0x8
type 0x5 pa 0xfff4e000 va 0xfff4e000 pages 0x1 attr 0x8000000000000008
type 0x2 pa 0xfff4f000 va 0xfff4f000 pages 0xb1 attr 0x8
type 0x4 pa 0x100000000 va 0x100000000 pages 0x40000 attr 0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2025 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 7.8 (RAMDISK) #49: Tue Oct 14 13:23:12 MDT 2025
[email protected]:/usr/src/sys/arch/riscv64/compile/RAMDISK
real mem = 4294967296 (4096MB)
avail mem = 4065189888 (3876MB)
SBI: OpenSBI v1.0, SBI Specification Version 0.3
random: boothowto does not indicate good seed
mainbus0 at root: StarFive VisionFive 2 v1.2A
cpu0 at mainbus0: SiFive U7 imp 4210427 rv64imafdc_zba_zbb
intc0 at cpu0
cpu0: 32KB 64b/line 64-way L1 I-cache, 32KB 64b/line 64-way L1 D-cache
cpu0: 2048KB 64b/line 2048-way L2 cache
"opp-table-0" at mainbus0 not configured
"display-subsystem" at mainbus0 not configured
"dvp-clock" at mainbus0 not configured
"gmac0-rgmii-rxin-clock" at mainbus0 not configured
"gmac0-rmii-refin-clock" at mainbus0 not configured
"gmac1-rgmii-rxin-clock" at mainbus0 not configured
"gmac1-rmii-refin-clock" at mainbus0 not configured
"hdmitx0-pixel-clock" at mainbus0 not configured
"i2srx-bclk-ext-clock" at mainbus0 not configured
"i2srx-lrck-ext-clock" at mainbus0 not configured
"i2stx-bclk-ext-clock" at mainbus0 not configured
"i2stx-lrck-ext-clock" at mainbus0 not configured
"mclk-ext-clock" at mainbus0 not configured
"oscillator" at mainbus0 not configured
"rtc-oscillator" at mainbus0 not configured
"stmmac-axi-config" at mainbus0 not configured
"tdm-ext-clock" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
plic0 at simplebus0
stfpciephy0 at simplebus0
stfpciephy1 at simplebus0
stfclock0 at simplebus0: stgcrg
syscon0 at simplebus0: "syscon"
stfclock1 at simplebus0: syscrg
syscon1 at simplebus0: "syscon"
stfclock2 at syscon1: pll
stfpinctrl0 at simplebus0
stfclock3 at simplebus0: aoncrg
syscon2 at simplebus0: "syscon"
"timer" at simplebus0 not configured
"cache-controller" at simplebus0 not configured
com0 at simplebus0: dw16550
com0: console
"i2c" at simplebus0 not configured
"i2c" at simplebus0 not configured
"spi" at simplebus0 not configured
"tdm" at simplebus0 not configured
"pwmdac" at simplebus0 not configured
"i2s" at simplebus0 not configured
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
"i2c" at simplebus0 not configured
"i2c" at simplebus0 not configured
"i2s" at simplebus0 not configured
"i2s" at simplebus0 not configured
"pwm" at simplebus0 not configured
"temperature-sensor" at simplebus0 not configured
"spi" at simplebus0 not configured
"timer" at simplebus0 not configured
"watchdog" at simplebus0 not configured
"crypto" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
stfrng0 at simplebus0
dwmmc0 at simplebus0: 198 MHz base clock
sdmmc0 at dwmmc0: 8-bit, mmc high-speed, dma
dwmmc1 at simplebus0: 198 MHz base clock
sdmmc1 at dwmmc1: 4-bit, sd high-speed, dma
dwqe0 at simplebus0 gmac 0dwqe0: reset timeout
: rev 0x52, address 6c:cf:39:00:18:5f
dwqe0: reset timeout
ytphy0 at dwqe0 phy 0: YT8531, rev. 11
dwqe1 at simplebus0 gmac 1: rev 0x52, address 6c:cf:39:00:18:60
ukphy0 at dwqe1 phy 0: Generic IEEE 802.3u media interface, rev. 8: OUI
0x000000, model 0x0012
"dma-controller" at simplebus0 not configured
"pinctrl" at simplebus0 not configured
"power-controller" at simplebus0 not configured
"csi-bridge" at simplebus0 not configured
"clock-controller" at simplebus0 not configured
"phy" at simplebus0 not configured
"camss" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"hdmi" at simplebus0 not configured
"clock-controller" at simplebus0 not configured
stfpcie0 at simplebus0
pci0 at stfpcie0
ppb0 at pci0 dev 0 function 0 "PLDA XpressRICH-AXI" rev 0x00
pci1 at ppb0 bus 1
xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev 3.00/1.00
addr 1
stfpcie1 at simplebus0
pci2 at stfpcie1
ppb1 at pci2 dev 0 function 0 "PLDA XpressRICH-AXI" rev 0x00
pci3 at ppb1 bus 1
nvme0 at pci3 dev 0 function 0 vendor "Phison", unknown product 0x5015 rev
0x01: intx, NVMe 1.4
nvme0: MSI M371 500GB, firmware EHFMD0.1, serial 511250910086002860
scsibus0 at nvme0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <NVMe, MSI M371 500GB, EHFM>
sd0: 476940MB, 512 bytes/sector, 976773168 sectors
gpiorestart0 at mainbus0
"pwmdac-codec" at mainbus0 not configured
"sound-pwmdac" at mainbus0 not configured
"clk_ext_camera" at mainbus0 not configured
sdmmc0: can't enable card
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Sandisk, SR128, 0086> removable
sd1: 121942MB, 512 bytes/sector, 249737216 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.20 addr 2
urtwn0 at uhub1 port 3 configuration 1 interface 0 "Realtek 802.11n NIC" rev
2.00/0.00 addr 3
urtwn0: MAC/BB RTL8188EU, RF 6052 1T1R, address 7c:f1:7e:c6:0d:e0
softraid0 at root
scsibus2 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
cpu0: regulator not implemented
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/riscv64 7.8 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell?
